Page History
Add_workflow_for_techpubs | ||||||||||
---|---|---|---|---|---|---|---|---|---|---|
|
Internal_display_only |
---|
Use the following workflow to activate High Availability on a pair of newly installed Edge 8300
Spacevars | ||
---|---|---|
|
Refer to High Availability for a description an overview of the High Availability option feature and a summary of the corresponding HA user interface changes supporting the option. Refer to Workflow for Initial Setup - High Availability for the complete installation and configuration instructions.
Prerequisites Anchor Prerequisites Prerequisites
- Login access at each device to the
web-based user interface (webUI)Spacevars 0 product4
webUI as user administrator (admin) on each device.product - Completion of the Workflow for Initial Setup - High Availability up to this procedure
- Ethernet interfaces on each device
Multiexcerpt include | ||||||
---|---|---|---|---|---|---|
|
- point in the workflow.
- A Node-Locked License (NLL) for
HA deployment uploaded to the Active device. Note that generating the license file in Salesforce requires theSpacevars 0 product
IDs of both devices. Refer to Obtaining and Installing an SBC SWe Edge Production Node-Locked License.Spacevars 0 product4 - Ethernet interfaces defined or reserved for the
function, as follows:Spacevars 0 product4 SBC Ethernet Interface Type Characteristics High Availability Each device has a dedicated
HA interface, High Availability.Spacevars 0 product4 When you enable HA for a device, you assign a local IP address that serves as the device's base HA IP address. From that, the system automatically assigns three IP addresses to support the device's HA interface.
Info title Note The base HA IP addresses of the two devices must be static IPv4 addresses on the same subnet and at least three addresses apart. Example: 10.10.10.41 and 10.10.10.44.
Here is an example of the IP address assignments for a pair of
devices after HA has been enabled on both devices:Spacevars 0 product IP Address Purpose Example: Active Device Standby Device base IP address HA interface 10.10.10.41 10.10.10.44 base IP address +1 Bridge 51 10.10.10.42 10.10.10.45 base IP address +2 Configuration sync2 10.10.10.43 10.10.10.46 - 1 Overrides any assignment made in the Setup Wizard.
- 2 Not viewable or configurable to the user from the webUI.
Media (packet) Each device has SWe Edge media (packet) interfaces, Ethernet 1 and Ethernet 3.
You will assign unique, static IP addresses to the media interfaces later, after you have enabled HA on the two devices. Refer to Workflow for Initial Setup - High Availability. (The SWe Edge settings replicate automatically to the Standby device in real-time when you configure the Active device.)
HA Deployment Example Anchor Job Aid HA Deployment Job Aid HA Deployment
Workflow
Step | Action |
---|---|
1 | Configure Enable High Availability on Active and Standby Devices |
2 | Verify High Availability Status |
3 | Install an HA License |
Enable High Availability on Active and Standby Devices
Enter the local and remote HA port interface IP addresses of the first High Availability device (referred to as an device, then allow the device to reboot. Repeat the steps for the other device.
Info | ||||
---|---|---|---|---|
| ||||
In the following procedure, to "Log in to your
|
to the
|
Info | ||||
---|---|---|---|---|
| ||||
When assigning local and remote IP addresses, they must be static IPv4 addresses on the same subnet and at least three addresses apart. Example: 10.10.10.41 and 10.10.10.44. |
Multiexcerpt include | ||||||
---|---|---|---|---|---|---|
|
Verify High Availability Status
Verify Check the HA pair High Availability status to ensure that both devices, referred to as the the Active and Standby devices (referred to as instances in the procedure) instances, are properly enabled.
Multiexcerpt include | ||||||
---|---|---|---|---|---|---|
|
Install an HA License
Install the HA license that applies to both devices.
Info | ||
---|---|---|
| ||
In step 3 of the following procedure, select SWe Edge from the Version dropdown list. |
Info | ||||
---|---|---|---|---|
| ||||
When you apply the HA license to the Active device, allow approximately 10 minutes for the license to appear and sync with the standby device. |
Multiexcerpt include SpaceWithExcerpt UXDOC121UXDOC122 MultiExcerptName Installing a Node-Locked License PageWithExcerpt UXDOC121UXDOC122:Install a License on the Active Instance of an SBC SWe Edge HA Pair