Page History

...

Workflow

Installing an SBC SWe Edge on a Hypervisor 

Anchor
Installing an SBC SWe Edge on a Hypervisor Installing an SBC SWe Edge on a Hypervisor

You must install a second SBC SWe Edge instance on VMware ESXi, KVM, or Hyper-V to upgrade an SA NLL SWe Edge to an HA NLL SWe Edge. For more information on installing an SBC SWe Edge instance on VMware ESXi, KVM, or Hyper-V, refer to:

...

Obtaining a Node-Locked License for an HA SWe Edge Pair

Anchor
Obtaining a Node-Locked License for an HA SWe Edge Pair Obtaining a Node-Locked License for an HA SWe Edge Pair

You must obtain a new NLL with two SWe Edge IDs for your HA SWe Edge pair, one SWe Edge ID for the Active instance and the other for the Standby instance. You will receive an email that contains information on the two SWe Edge IDs after you purchase an NLL license from Ribbon Sales or through the Ribbon Partner Portal.

For more information on obtaining a new NLL with a SWe Edge ID, refer to Obtaining and Installing an SBC SWe Edge Production Node-Locked License.

Deploying High Availability on SBC SWe Edge 

Anchor
Deploying High Availability on SBC SWe Edge Deploying High Availability on SBC SWe Edge

The following workflow defines the procedures for deploying HA on an SBC SWe Edge.

...

Workflow

Enable High Availability on Active and Standby SWe Edge Instances 

Anchor
Enable High Availability on Active and Standby SWe Edge Instances Enable High Availability on Active and Standby SWe Edge Instances

Enabling HA on Active and Standby SWe Edge instances allows you to have increased system stability during mid-call failovers.

...

1. Log in to your SBC SWe Edge instance. 

2. Click the Settings tab at the top of the WebUI.

3. In the left navigation pane, go to System > Node-level Settings.

4. Click Enable HA.
   
   Enable HA on SBC SWe Edge Instance
   
   

    

5. Enter the Local IP Address, Local IP Netmask, and Remote IP Address in the Create HA Interface pop-up window. 
   
   

   Info
   title Note
   The Local IP is the HA IP address of the instance you are currently in. The remote IP is the other HA IP address for the other example, as mentioned in the prerequisites section.

   
   Create an HA Interface on the Instance
   
   
   
   

6. You will be prompted with the below confirmation. Click on OK to continue.
   
   
   

7. Click OK. The instance will reboot for about 2 minutes until it displays the HA interface. 

   HA Interface on the Active Instance

   

8. Confirm that HA is enabled on this instance. The HA role of the instance is seen in the right-hand corner of the WebUI.

   The HA Role is Shown at the Right Hand Corner of the Instance WebUI 

   

9. Repeat steps 1 to 7 in the second instance, becoming the Standby. 

Verify High Availability Status 

Anchor
Verify High Availability Status Verify High Availability Status

Verifying HA pair status allows you to ensure that both Active and Standby SBC SWe Edge instances are correctly enabled.

...

1. Log in to the Active HA instance. 

2. Click the Diagnostics tab at the top of the WebUI.

3. In the left navigation pane, go to High Availability > HA Status Details to view the HA status.
   

4. Repeat steps 1 to 3 on the Standby HA instance.
   

   
   

Install a Node-Locked License 

Anchor
Install a Node-Locked License Install a Node-Locked License

Installing a Node-Locked license allows you to use SBC SWe Edge features. Licenses applied to the Active instance are replicated to the Standby instance. 

...