Versions Compared

Old Version 1

changes.mady.by.user Ribbon Communications

Saved on

compared with

New Version 2

changes.mady.by.user Ribbon Communications

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

Add_workflow_for_techpubs
AUTH1AUTH2UserResourceIdentifier{userKey=8a00a0c862eadf5e0163170affe7001b8a00a0c8613a801e016167f8a31a002b, userName='null'}
JIRAIDAUTHCHOR-10741
AUTH1REV5UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26cb8305e98a00a0c862eadf5e0163170affe7001b, userName='null'}
JIRAIDAUTHCHOR-10133
REV5REV6UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26cd5909df8a00a02355cd1c2f0155cd26cb8305e9, userName='null'}
REV3REV6UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26cb2305708a00a02355cd1c2f0155cd26cb8305e9, userName='null'}
REV1REV3UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26ca2f03d18a00a0c8613a801e016167f8a31a002b, userName='null'}
REV2REV1UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26c9b903048a00a0c8613a801e016167f8a31a002b, userName='null'}


The following workflow defines the procedures for upgrading an SA NLL SWe Edge to an HA NLL SWe Edge in a non-RAMP scenario.

...

  1. Log in to your SBC SWe Edge instance. 

  2. Click the Settings tab at the top of the WebUI.

  3. In the left navigation pane, go to System > Node-level Settings.

  4. Click Enable HA.

    Enable HA on SBC SWe Edge Instance
    Image Added
    Image Removed

     

  5. Enter the Local IP Address, Local IP Netmask, and Remote IP Address in the Create HA Interface pop-up window. 

    Info
    titleNote

    The Local IP is the HA IP address of the instance you are currently in. The remote IP is the other HA IP address for the other example, as mentioned in the prerequisites section. 


    Create an HA Interface on the Instance
    Image RemovedImage Added


  6. You will be prompted with the below confirmation. Click on OK to continue.
    Image Removed
    Image Added

  7. Click OK. The instance will reboot for about 2 minutes until it displays the HA interface. 

    HA Interface on the Active Instance

    Image RemovedImage Added

  8. Confirm that HA is enabled on this instance. The HA role of the instance is seen in the right-hand corner of the WebUI.

    The HA Role is Shown at the Right Hand Corner of the Instance WebUI 

    Image RemovedImage Added

  9. Repeat steps 1 to 7 in the second instance, becoming the Standby. 

...

  1. Log in to the Active HA instance. 

  2. Click the Diagnostics tab at the top of the WebUI.

  3. In the left navigation pane, go to High Availability > HA Status Details to view the HA status.
    Image RemovedImage Added

  4. Repeat steps 1 to 3 on the Standby HA instance.
    Image RemovedImage Added


Install a Node-Locked License 
Anchor
Install a Node-Locked License
Install a Node-Locked License

...

  1. Log in to the Active instance.

  2. Click the Settings tab at the top of the WebUI.

  3. In the left navigation window, go to System > Licensing > Install New License.
    Image RemovedImage Added

  4. Click Choose File and upload your license.

  5. Click Decode to see the license details.
    Image RemovedImage Added

  6. Click Apply. The newly added license can be seen in the Feature Licenses Decoded from the Provided License Key window. 

...