Versions Compared

Old Version 2

changes.mady.by.user Ribbon Communications

Saved on

compared with

New Version Current

changes.mady.by.user Ribbon Communications

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

Add_workflow_for_techpubs
AUTH1UserResourceIdentifier{userKey=8a00a0c87e188912017e4c24a00e00168a00a02355cd1c2f0155cd26cd5909df, userName='null'}
JIRAIDAUTHSBX-116624132372
REV5UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26cb8305e98a00a02355cd1c2f0155cd26cd5909df, userName='null'}
REV6UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26cd5909df, userName='null'}
REV3UserResourceIdentifier{userKey=8a00a0c86cea5831016d24084ff500228a00a02355cd1c2f0155cd26c91d01f9, userName='null'}
REV1UserResourceIdentifier{userKey=8a00a0c86cea5831016d24084ff500228a00a02355cd1c2f0155cd26cbf006d2, userName='null'}


Excerpt Include
_More than 32 vCPUs is not supported
_More than 32 vCPUs is not supported
nopaneltrue

Warning
titleWARNING

The recommended hardware and software settings are intended to ensure optimum 

Spacevars
0product2
stability and performance. If the recommended settings are not used, the 
Spacevars
0product2
system may not behave as expected.

Panel

In this section:

Table of Contents
maxLevel4


This section describes 

Spacevars
0product2
 hardware and software requirements and recommendations on KVM.

To install and configure 

Spacevars
0product2
, make sure the Virtual Machine (VM) host meets the following recommended hardware, server platform and software requirements.

Warning
titleWarning
The recommended hardware and software settings are intended to ensure optimum 
Spacevars
0product2
stability and performance

.

If the recommended settings are not used, the 

Spacevars

0product2
system may not behave as expected.

SBC SWe for KVM Hypervisor – Server Hardware Requirements


Multiexcerpt
MultiExcerptNameKVM Hardware

The following table lists the server hardware requirements.

Configuration Requirement
Processor

Intel Xeon processors (Nehalem micro-architecture or above) with 6 cores and above (processors should support hyper threading).

Info
titleNote

Ribbon recommends using Westmere (or newer) processors for better SRTP performance. These processors have the AES-NI instruction set for performing cryptographic operations in hardware.


Info
titleNote

The supported CPU Family number is 6 and CPU Model number must be newer than 26. Refer to the Intel Architecture and Processor Identification document for more information.

 

 RAMMinimum 24 GB
Hard DiskMinimum 500 GB
Network Interface Cards (NICs)

Minimum 4 NICs

The following are supported for configuring as SR_IOV:

  • Cisco VIC
  • Intel I350
  • Intel x540
  • Intel x550
  • Intel x710
  • Intel 82599 Ethernet adapters
  • Mellanox Connect - 4x
  • Mellanox Connect - 5x


Info
titleNote

Use the latest firmware for the specific NIC corresponding to the hardware platform. 


Info
titleNote

Make sure NICs have multi-queue support which enhances network performance by allowing RX and TX queues to scale with the number of CPUs on multi-processor systems.


Ports

Number of ports allowed:


Warning
titleWarning

The 

Spacevars
0product2
software runs only on platforms using Intel processors. Platforms using AMD processors are not supported.



BIOS Setting Recommendations

Ribbon recommends the following BIOS settings for optimum performance:

BIOS ParameterRecommended
Setting		Details
Intel VT-x (Virtualization Technology)EnabledFor hardware virtualization
Intel Hyper-ThreadingEnabled
Intel Turbo BoostEnabled
CPU Power ManagementMaximum Performance
Sub-NUMA ClusteringDisabledOnly applies if it is present as an option on the server


Example BIOS setting recommendations for HP DL380p Gen8 servers are shown below. For BIOS settings of other servers, refer to the respective vendor's website.


BIOS Setting Recommendations for HP DL380p Gen8 Servers

BIOS ParameterRecommended
Setting		Default Value
HP Power ProfileMaximum PerformanceBalanced Power and Performance
Thermal ConfigurationMaximum CoolingOptimal Cooling
HW PrefetchersDisabledEnabled
Adjacent Sector PrefetcherDisabledEnabled
Processor Power and Utilization MonitoringDisabledEnabled
Memory Pre-Failure NotificationDisabledEnabled
Memory Refresh Rate1x Refresh2x Refresh


SBC SWe for KVM Hypervisor – Software Requirements


Multiexcerpt
MultiExcerptNameKVM Software

The minimum SBC SWe requirements for a KVM hypervisor environment are listed in the following table.

SoftwareVersionTested or Qualified Version
KVM Module 3.10.0 or above3.10.0
QEMU Emulator  1.5.31.5.3
libvirtd (libvirt)1.1.11.1.1
virt-manager0.10.00.10.0



Downloading the SBC SWe Software Package

For more information, see Downloading the SBC SWe Software Package.

Info
titleNote

Ensure Processors and VM configuration (CPUs, RAM, Virtual Hard Disk, NICs, and Bridge settings) are identical for an SBC SWe HA pair.


Info
titleNote

Do not change BIOS settings once they are applied on the server.

KVM Configuration and Settings 

ConfigurationSettings
 vCPU

Minimum 4 vCPUs required. Any number of vCPUs may be configured depending upon the call capacity requirements, but the number should be even (4, 6, 8, etc.) to avoid impacting performance.  

CPU resource reservation and pinning are required.

 vRAM

Reserve the memory based on call capacity and configuration requirements. Refer to benchmarking data for supported call capacities with different configuration limits.

Memory resource reservation is required.

Virtual Hard Disk

Set Hard Disk (virtual) size as 100 GB or more (based on requirements of retaining CDRs, logs, etc. for number of days).

Note: Hard disk size cannot be changed after the SBC SWe software is installed.

vNICs

Set number of virtual NICs as 4 (1-MGMT, 1-HA, 1-PKT0 and 1-PKT1).

  • Use Virt-IO drivers only for MGMT and HA. VIRT-IO interfaces are not recommended for higher call loads.
  • For PKT0 and PKT1 the driver to use depends on the parallel sessions to support - it is either VIRT-IO or SR-IOV.
  • Associate each vNIC to separate bridges.

Multiexcerpt include
MultiExcerptName_vlan_sriov_disable_dcb
PageWithExcerpt_VLAN_SRIOV_Disable_DCB


Info
titleNote

You can instantiate the SBC SWe in smaller-sized configurations that use limited memory and vCPU resources, if required. However, the limited resources place some restrictions on capacity and capabilities. Refer to Small SBC SWe Deployment Characteristics and Performance Metrics for Small SBC SWe Configuration Performance MetricsConfigurations for more information.