| Excerpt |
|---|
This object specifies the gateway to which you wish to direct traffic from your Packet, Management, or Link Interface. In effect, this object allows you to add, change, and delete gateways (next Hops) to these interfaces. Interface and static routes combine to form the IP routing table for your network. This table must ultimately provide a route to each potential call destination IP address. The static route is used to add static IP routes for the IP interfaces. A static route indicates the nextHop gateway and IP interface that should be used for a particular peer network IP prefix.
| Include Page |
|---|
| _Unique_IP_for_SigPort |
|---|
| _Unique_IP_for_SigPort |
|---|
|
| Include Page |
|---|
| _IP_IGs_ServedBySeperateProcessors |
|---|
| _IP_IGs_ServedBySeperateProcessors |
|---|
|
To View Static RouteOn the SBC main screen, |
...
choose a path: - Configuration > System Provisioning > Category: Base Provisioning > Static Route
- All > Address Context > Static Route
|
...
...
...
Figure 1: System Provisioning - Static Route
 Image Modified
The Static Route can be checked for each Address Context or for all the Address Contexts created. Use the drop-down box to select the desired Address Context. To Edit Static RouteTo edit any of the Static Routes in the list, click the radio button next to the specific Static Route name. |
...
The Edit Selected Static Route |
...
window is displayed below. |
Figure 2: Static Route Edit Window
Image Modified Make the required changes and |
...
...
at the right hand bottom of the panel to save the changes made. | Note |
|---|
The SBC does not allow to edit |
|
...
the Condition for a Static Route. To change the configuration |
|
...
...
the Static Route and reconfigure it. |
To Create Static RouteTo create a new Static Route, |
...
...
tab on the Static Route List panel. |
...
The Create New Static Route window is displayed. |
...
Image Modified |
...
...
Static Route Parameters: Parameter | Length/Range | Description |
|---|
Destination IP Address |
|
...
IPv4: dotted decimal form |
|
...
...
IPv6: hexadecimal/colon form |
|
...
| The IPv4/IPv6 destination IP address. | Prefix | 0-128 |
|
...
| The IP prefix of this static route entry. | Next Hop | IPv4: dotted decimal form IPv6: hexadecimal/colon form | The IP address of the next system en |
|
...
route to the destination. | IP Interface |
|
...
...
N/A | Choose an IP interface group name for this static route. | IP Interface Name |
|
...
...
the IP interface name for this entry. | Preference |
|
...
100-2147483647 | The route preference value. The management route preference range is 1-99 and the packet route preference range is greater than or equal to 100. The default is 100. | | Condition | N/A | An element in |
|
...
the Static Route configuration that holds the conditions based on |
|
...
which routes are added to |
|
...
an SBC pair with HA configuration. - CE Name – The name of the computing element that hosts the port used by the IP interface.
Currently, |
|
...
Condition supports only one child element - |
|
...
...
The Condition option is only applicable to non-management interfaces. |
|
...
...
| Note |
|---|
For a High Availability (HA) pair configuration, the SBC allows configuring |
|
...
a Static Route for a specific host |
|
...
or CE Name among the active and standby hosts of |
|
...
an HA pair configuration using |
|
...
the Condition element. The Condition element stores the conditions based on |
|
...
which routes are added to |
|
...
an SBC pair with HA configuration. Currently, |
|
...
the Condition element only supports |
|
...
...
the Condition using a specific CE Name, ensure that the IP Interface Group |
|
...
Name and IP Interface Name are configured. You cannot configure and save these three elements simultaneously. For further details, refer |
|
...
...
...
You can only add Static Routes with specific CE Names for packet interfaces. |
To Copy Static RouteTo copy |
...
a static route and make minor changes, click the radio button next to the |
...
specific static route to highlight the row. |
...
...
Route tab on the Static Route List panel. |
...
The Copy Selected Static Route |
...
window is displayed along with the field details, which can be edited. |
...
Image Modified
Make the required changes to the required fields and |
...
...
to save the changes. The copied Static Route is displayed at the bottom of the original Static Route in the Static Route List panel. To Delete Static RouteTo delete any of the created Static Route, click the radio button next to the |
...
...
that you want to delete. Click |
...
...
symbol at the end of the highlighted row. A delete confirmation message appears seeking your decision. |
...
Click Yes to remove the specific Static Route from the list. |
...
- deleting the CE Name separately.
- The Static
|
|
...
- Route is deleted only from the instance in which it is configured
|
|
...
- and not from both active and standby instances of
|
|
...
...