Page History

img.confluence-embedded-image { display: inline-block !important; }

Usage of the Easy Config wizard to configure the

NTT DOCOMO Officelink, SoftBank ConnecTalk, Softbank White Office and Telstra Enterprise SIP Connect are supported in SBC 1000-2000 only.

For the

Broadsoft Trunk is applicable only if the user endpoint is an IP phone.

These instructions assume the SBC Easy Config wizard is running. See Using the Easy Configuration Wizard.

The scenario in which the configuration template is provided. In this case, select SIP Trunk ↔ IP Phones.

Enter the name to describe the SIP Trunk ↔ IP Phone setup.

The country in which the  SIP Trunk ↔ IP Phones originates.

The E911 Elin number from the "CompanyName" field configured in Lync location services is used as the authoritative Call Back number for outgoing E911 calls, and is always the preferred configuration. Specifically, it will take precedence over any Callback Number number configuration in Lync Setup. For more information, see Creating and Modifying Entries to Transformation Tables.

This field defines the Emergency Services for outgoing numbers. For the purpose of this illustration above, Emergency Services is not selected. Field definitions are defined below.

Options:  ELIN Identifier, E911/E112 or None.

Call Back Number in string format. This field is displayed only when ELIN Identifier or E911/E112 is selected from Emergency Services.

Second Call Back Number in string format. This field is displayed only when ELIN Identifier or E911/E112 is selected from Emergency Services.

Defines the Public Safety Answering Point Number. Valid entry 1 - 127 characters.

Number of simultaneous SIP sessions allocated. Valid entry 1 - 960.

The SIP trunk used for connection to the IP phones. Valid options: ATT SIP Trunk, Other SIP Trunk, Verizon SIP Trunk, KDDI SIP Trunk, Broadsoft Trunk, SoftBank ConnecTalk, SoftBank White Office, NTT DOCOMO Officelink, and Twilio SIP Trunk.

The SIP Trunk selected determines the field options displayed in Step 2. see Step 2 - Configure SIP Details for Endpoint.

Defines the Broadsoft Trunk Type. Valid entry: Enterprise or Access.

This field is available only when the SIP Trunk type is Broadsoft Trunk.

The FQDN or IP address of the Remote Peer service provider.

The IP protocol used for sending and receiving SIP messages between SBC and the Border Element Server. Valid entry UDP or TCP.

The SIP Server Port number used for sending and receiving SIP messages between SBC and the Border Element Server.

Enables or disables the secondary Remote Peer service provider configured. 

Specifies the Secondary Border Element Service provider. Valid entry: IP Address or FQDN. This field is available only when Use Secondary Border Element Server is Enabled.

The Protocol used for communicating with the Secondary Border Element Server. Valid entry: UDP or TCP. This field is available only when Use Secondary Border Element Server is Enabled.

The Port Number is used for sending and receiving messages between SBC and the Secondary Border Element server. This field is available only when Use Secondary Border Element Server is Enabled.

Enables/disables support for the AT&T Simultaneous Ring feature. Valid option: Yes or No.

Enables/disables the AT&T Toll Free option. Valid option: Enabled or Disabled.

The Toll Free Access Number to use when the AT&T IP Toll Free option is enabled.

Selects the IP phone numbering plan to be used. Valid options: E.164, National, or Extension.

The Protocol used for communicating with the IP phone.  Valid entry: UDP or TCP.

The Port Number used for sending and receiving messages between SBC and the IP phone. Default entry: 5060.

Configure a network address and Netmask for the host or subnet in which the IP phone resides.

Network IP. IP address for the destination host or subnet in which the IP phone resides.

Netmask. The network mask of the destination host or subnet in which the IP phones resides.

To create a network address, click the add icon.  Enter the Network IP and Network Mask and click OK.

The main telephone number associated with the SIP trunk.

Selects the IP phone numbering plan to be used. Valid options: E.164, National, or Extension. 

For SIP Registrar, refer to

Configure a network address and Netmask for the host or subnet in which the IP phone resides.

Network IP. IP address for the destination host or subnet in which the IP phone resides.

Netmask. The network mask of the destination host or subnet in which the IP phones resides.

For an IP Phone as the user end point, Easy Configuration loads a generic template which follows the “National Numbering Plan” guidelines.

Defines the IP phone numbering plan to be used. Valid options: E.164, National, or Extension.

The Protocol used for communicating with the IP phone.  Valid entry: UDP or TCP.

The Port Number used for sending and receiving messages between SBC and the IP phone. Default entry: 5060.

Configure a network address and Netmask for the host or subnet in in which the IP phones reside.

• Network IP. IP address for the destination host or subnet in which the IP phone resides.
• Netmask. The network mask of the destination host or subnet in which the IP phones resides.

To create a network address, click the add icon.  Enter the Network IP and Network Mask and click OK.

The FQDN or IP address of the Remote Peer service provider.

The IP protocol used for sending and receiving SIP messages between the

The SIP Server Port number used for sending and receiving SIP messages between the

Enables or disables the secondary Remote Peer service provider configured. 

Specifies the Secondary Border Element Service provider. Valid entry: IP Address or FQDN. This field is available only when Use Secondary Border Element Server is Enabled.

The Protocol used for communicating with the Secondary Border Element Server. Valid entry: UDP or TCP. This field is available only when Use Secondary Border Element Server is Enabled.

The Port Number used for sending and receiving messages between the

Defines the IP phone numbering plan to be used. Valid options: E.164, National, or Extension.

The Protocol used for communicating with the IP phone. Valid entry: UDP or TCP.

The Port Number used for sending and receiving messages between the

Configure a network address and Netmask for the host or subnet in in which the IP phones reside.

Network IP: IP address for the destination host or subnet in which the IP phone resides.

Netmask: The network mask of the destination host or subnet in which the IP phones resides.

To create a network address, click the add icon.  Enter the Network IP and Network Mask and click OK.

The host IP address or FQDN of the primary SIP server.

The host IP address or FQDN of the secondary SIP server.

The method to connect networks. This field has the following options: Routerless and Router.

The user-specified IP address for SIP signaling messages.

The ID that authenticates with the router at the gateway of the network.

The password that authenticates with the router at the gateway of the network.

Re-enter the password for the router that serves as the network gateway.

The IP or FQDN of the SIP Profile and Contact Registrant Table.

This field automatically generates using the Gateway ID at the From/To Header Host.

Select the IP phone numbering plan to use. This field has the following options: E.164, National, and Extension.

Define the number of users. A valid entry is between 1 - 1000.

The Protocol that communicates with the IP phone. This field has the following options: UDP and TCP.

The Port Number that sends and receives messages between the SBC and the Server Pool Host. The default value is 5060.

Configure a network address and network mask for the host or subnet in which the IP phone resides.

Network IP: The IP address for the destination host or subnet in which the IP phone resides.

Network Mask: The network mask of the destination host or subnet in which the IP phone resides.

To create a network address, click the add icon.  Enter the Network IP and Network Mask and click OK.

The method used for connecting networks. Options are: Routerless and Router. On selection of Routerless, the Easy Config displays the Signaling/Media Source IP field and the SIP Server field. On selection of Router, the Easy Config displays the SIP Server field only.

The user-specified IP address to be used for SIP signaling messages. The Signaling/Media Source IP field does not display when the option selected for the WAN Link field is Router.

The host IP address or FQDN for the SIP server.

The ID used for authenticating with the router at the gateway of the network.

The password used for authenticating with the router at the gateway of the network.

Re-entry of the password for the router serving as the network gateway.  

The public address that points to the domain for users, for use in the Contact Registrant Entry. For example, specify: GatewayID@SIPServer.

Defines the IP phone numbering plan to be used. Valid options: E.164, National, or Extension.

The Protocol used for communicating with the IP phone.  Valid entry: UDP or TCP.

The Port Number used for sending and receiving messages between SBC and the IP phone. Default entry: 5060.

Configure a network address and Netmask for the host or subnet in in which the IP phones reside.

Network IP. IP address for the destination host or subnet in which the IP phone resides.

Netmask. The network mask of the destination host or subnet in which the IP phones resides.

To create a network address, click the add icon.  Enter the Network IP and Network Mask and click OK.

The state to use in configuring the outbound proxy for the Provider SIP Trunk. Options include: Australia Capital Territory, New South Wales, Northern Territory, Queensland, South Australia, Tasmania, Victoria, and Other (a user-specified FQDN).

Hard coded as UDP and Port 5060.

The IPv4 address used to create a Split DNS entry for the Telstra domain.

The SIP Connect Domain or Realm to which the specified IP address will map.

The User ID for use in authentication.

The password to use when authenticating with the User ID.

The re-entered password for confirmation.

The 9-digit pilot number Telstra assigned for use with the SIP Connect trunking service.

Defines the IP phone numbering plan to be used. Valid options: E.164, National, or Extension.

The Protocol used for communicating with the IP phone.  Valid entry: UDP or TCP.

The Port Number used for sending and receiving messages between SBC and the IP phone. Default entry: 5060.

Configure a network address and Netmask for the host or subnet in in which the IP phones reside.

Network IP. IP address for the destination host or subnet in which the IP phone resides.

Netmask. The network mask of the destination host or subnet in which the IP phones resides.

To create a network address, click the add icon.  Enter the Network IP and Network Mask and click OK.

The FQDN or IP address of the Remote Peer service provider.

The IP protocol used for sending and receiving SIP messages between SBC and the Border Element Server. This value is fixed at UDP.

The SIP Server Port number used for sending and receiving SIP messages between SBC and the Border Element Server.

Selects the IP phone numbering plan to be used. Valid options: E.164, National, or Extension.

The Protocol used for communicating with the IP phone.  Valid entry: UDP or TCP.

The Port Number used for sending and receiving messages between SBC and the IP phone. Default entry: 5060.

Configure a network address and Netmask for the host or subnet in which the IP phone resides.

Network IP. IP address for the destination host or subnet in which the IP phone resides.

Netmask. The network mask of the destination host or subnet in which the IP phones resides.

To create a network address, click the add icon.  Enter the Network IP and Network Mask and click OK.

The FQDN of the server domain.

Enables/disables Enterprise Trunking. This field is available only when Enterprise Trunking is selected in the Broadsoft Trunk Type field.

Selects the IP phone numbering plan to be used. Valid options: E.164, National, or Extension.

The Protocol used for communicating with the IP phone.  Valid entry: UDP or TCP.

The Port Number used for sending and receiving messages between SBC and the IP phone. Default entry: 5060.

Configure a network address and Netmask for the host or subnet in which the IP phone resides.

Network IP. IP address for the destination host or subnet in which the IP phone resides.

Netmask. The network mask of the destination host or subnet in which the IP phones resides.

To create a network address, click the add icon.  Enter the Network IP and Network Mask and click OK.

Selects the IP phone numbering plan to be used. Valid options: E.164, National, or Extension.

The Protocol used for communicating with the IP phone.  Valid entry: UDP or TCP.

The Port Number used for sending and receiving messages between SBC and the IP phone. Default entry: 5060.

Configure a network address and Netmask for the host or subnet in which the IP phone resides.

Network IP. IP address for the destination host or subnet in which the IP phone resides.

Netmask. The network mask of the destination host or subnet in which the IP phones resides.

To create a network address, click the add icon.  Enter the Network IP and Network Mask and click OK.