...
Info |
---|
|
Perform all the procedures in this section in the order they are presented. |
Prerequisites
The following information is required to complete the procedures.
...
Information needed | Value | Comments |
---|
Slot number of the I/O card to be provisioned in the |
| If available, it is recommended to use slot value 4 or 5 for the first TDM card being added to your . |
Name of the HA subnet soft bridge |
|
|
Path to the IO card software image |
|
|
Configure the TDM I/O Cards on Host 1
Start
Login to the MA-RMS server.
Execute the self-extracting installation script as follows to install the TDM IO software:
Code Block |
---|
[root@bw22u0 dsc_swe_install]#
./install_tdm_io.sh
Verifying archive integrity... 100% All good.
Uncompressing DSC TDM I/O card installer 100%
This script will install the driver rpm:
iphwaeto-1.14.ribbon-14.x86_64-centos6-2-6-32.rpm
which includes IO image:
rel_11_00_p13.swe.img
If these are not correct, please download the latest version of this script and the rpm.
Press Enter to continue
iphwaeto version installed is already at expected level. Reinstalling...
Preparing... ########################################### [100%]
1:iphwaeto ########################################### [100%]
Could only find 1 card(s) on this system.
Verify this matches the expected number of cards. |
Re-source environment variables:
Run dscvm_io_mgmt utility.
Code Block |
---|
# dscvm_io_mgmt |
Make sure both cards are showing as Unconfigured.
Code Block |
---|
DSC SWe I/O Cards
Index Location PCI Address Status Slot KVM Bridge
----- -------- ----------- ------ ---- ----------
0 0000:04:00.0 0000:05:04.0 Unconfigured NA NA
1 0000:85:00.0 0000:86:04.0 Unconfigured NA NA
Please select a card [0-1] or 'q' to quit: |
Info |
---|
|
The numbers in the above output can differ. |
- Configure the first TDM I/O card.
Select card/Index - 0
Code Block |
---|
Please select a card [0-1] or 'q' to quit: 0 |
Select action - C
Code Block |
---|
DSC SWe I/O Cards
Card 0: pci0 0000:04:00.0 Unconfigured
------------------------
(C)onfigure
(I)nstall Image and Start
(S)top
(R)estart
(U)nconfigure
Boot (F)irmware Debug Access
(A)pplication Debug Access
Please select an action [C,I,S,R,U,F,A], 'b' for back, or 'q' to quit: C |
Enter the root password.
Code Block |
---|
Please enter the root password for the DSC SWe
root@192.168.240.1's password: |
A list of cards is displayed. Enter the slot number 7.
Code Block |
---|
DSC SWe I/O Cards
Card 0: pci0 0000:04:00.0 Unconfigured
------------------------
Please enter a DSC SWe slot number from this list: 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
or 'b' for back, or 'q' to quit: 7 |
Enter HA subnet soft bridge - br2-103
Code Block |
---|
The slot number will be applied when flashing the I/O card image.
Please enter a KVM softswitch, 'NA' to skip, 'b' for back, or 'q' to quit: br2-103 |
Tip |
---|
|
The error "bridge NA does not exist!" is expected. |
Code Block |
---|
bridge NA does not exist!
DSC SWe I/O Cards
Index Location PCI Address Status Slot KVM Bridge
----- -------- ----------- ------ ---- ----------
0 0000:04:00.0 0000:05:04.0 Offline 7 br2-103
1 0000:85:00.0 0000:86:04.0 Unconfigured NA NA
Please select a card [0-1] or 'q' to quit: |
Configure the second TDM I/O card.
Select card/Index - 1
Code Block |
---|
Please select a card [0-1] or 'q' to quit: 1 |
Select action - C
Code Block |
---|
DSC SWe I/O Cards
Card 1: pci1 0000:04:00.0 Offline
------------------------
(C)onfigure
(I)nstall Image and Start
(S)top
(R)estart
(U)nconfigure
Boot (F)irmware Debug Access
(A)pplication Debug Access
Please select an action [C,I,S,R,U,F,A], 'b' for back, or 'q' to quit: C |
Enter the root password.
Code Block |
---|
Please enter the root password for the DSC SWe
root@192.168.240.1's password: |
A list of cards is displayed. Enter the slot number 6.
Code Block |
---|
DSC SWe I/O Cards
Card 1: pci1 0000:85:00.0 Unconfigured
------------------------
Please enter a DSC SWe slot number from this list: 3 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
or 'b' for back, or 'q' to quit: 6 |
Enter HA subnet soft bridge - br2-103
Code Block |
---|
The slot number will be applied when flashing the I/O card image.
Please enter a KVM softswitch, 'NA' to skip, 'b' for back, or 'q' to quit: br2-103 |
Tip |
---|
|
The error "bridge NA does not exist!" is expected. |
Code Block |
---|
HOST1:
DSC SWe I/O Cards
Index Location PCI Address Status Slot KVM Bridge
----- -------- ----------- ------ ---- ----------
0 0000:06:00.0 0000:07:04.0 Offline 7 br2-103
1 0000:85:00.0 0000:86:04.0 Offline 6 br2-103 |
Install Image and start the card.
Info |
---|
|
This following steps require the information for the path to the I/O image on the server. The TDM card will show up as online once this is complete. This procedure takes about 2 to 3 minutes to complete. |
- Install the first TDM card.
Select card/Index - 0
Code Block |
---|
Please select a card [0-1] or 'q' to quit: 0 |
Select action - I
Code Block |
---|
DSC SWe I/O Cards
Card 0: pci0 0000:04:00.0 Offline
------------------------
(C)onfigure
(I)nstall Image and Start
(S)top
(R)estart
(U)nconfigure
Boot (F)irmware Debug Access
(A)pplication Debug Access
Please select an action [C,I,S,R,U,F,A], 'b' for back, or 'q' to quit: I |
Press ENTER.
Code Block |
---|
DSC SWe I/O Cards
Card 0: pci0 0000:04:00.0 Offline DSC Slot 7
------------------------
Please enter a DSC SWe I/O card image file [/opt/ribbon/dsc_io/tools/rel_11_00_p10.swe.img]: <press Enter and wait> |
Select action - b
Code Block |
---|
DSC SWe I/O Cards
Card 0: pci0 0000:04:00.0 Offline
------------------------
(C)onfigure
(I)nstall Image and Start
(S)top
(R)estart
(U)nconfigure
Boot (F)irmware Debug Access
(A)pplication Debug Access
Please select an action [C,I,S,R,U,F,A], 'b' for back, or 'q' to quit: b |
Code Block |
---|
DSC SWe I/O Cards
Index Location PCI Address Status Slot KVM Bridge
----- -------- ----------- ------ ---- ----------
0 0000:04:00.0 0000:05:04.0 Online 7 br2-103
1 0000:85:00.0 0000:86:04.0 Offline 6 br2-103
Please select a card [0-1] or 'q' to quit: |
Install the second TDM card.
Select card/Index - 1
Code Block |
---|
Please select a card [0-1] or 'q' to quit: 1 |
Select action - I
Code Block |
---|
DSC SWe I/O Cards
Card 1: pci1 0000:04:00.0 Online
------------------------
(C)onfigure
(I)nstall Image and Start
(S)top
(R)estart
(U)nconfigure
Boot (F)irmware Debug Access
(A)pplication Debug Access
Please select an action [C,I,S,R,U,F,A], 'b' for back, or 'q' to quit: I |
Press ENTER.
Code Block |
---|
DSC SWe I/O Cards
Card 1: pci1 0000:85:00.0 Offline DSC Slot 6
------------------------
Please enter a DSC SWe I/O card image file [/opt/ribbon/dsc_io/tools/rel_11_00_p10.swe.img]: <press Enter and wait> |
Select action - b
Code Block |
---|
DSC SWe I/O Cards
Card 1: pci1 0000:04:00.0 Online
------------------------
(C)onfigure
(I)nstall Image and Start
(S)top
(R)estart
(U)nconfigure
Boot (F)irmware Debug Access
(A)pplication Debug Access
Please select an action [C,I,S,R,U,F,A], 'b' for back, or 'q' to quit: b |
Code Block |
---|
DSC SWe I/O Cards
Index Location PCI Address Status Slot KVM Bridge
----- -------- ----------- ------ ---- ----------
0 0000:04:00.0 0000:05:04.0 Online 7 br2-103
1 0000:85:00.0 0000:86:04.0 Online 6 br2-103
Please select a card [0-1] or 'q' to quit: |
Stop the dscvm-io service.
Code Block |
---|
# service dscvm-io stop |
Code Block |
---|
Bringing pci0 down
Bringing pci1 down
---------------------------------------------------------
/opt/ribbon/dsc_io/driver/iphwaetodrv 1.09 for Linux (C)Interphase Corp. 2008
iphwaeto driver remove
--------------------------------------------------------- |
Start the dscvm-io service.
Code Block |
---|
# service dscvm-io start |
Code Block |
---|
---------------------------------------------------------
/opt/ribbon/dsc_io/driver/iphwaetodrv 1.09 for Linux (C)Interphase Corp. 2008
iphwaeto driver load
---------------------------------------------------------
Loading PCI network. Success |
Tip |
---|
|
Stopping and Starting the dscvm-io service attaches the PCI device to the bridge configured on the cards. |
Proceed to the appropriate procedure
Install Host Software to Enable TDM FunctionalityCommission the TDM I/O Card with the DSC SWe in the MA-RMS Server.
Access the TDM I/O card with no DSC SWe in the MA-RMS server.
Configure the TDM I/O Cards on Host 2
Start
Login to the MA-RMS server.
Execute the self-extracting installation script as follows to install the TDM IO software:
Code Block |
---|
[root@bw22u0 dsc_swe_install]#
./install_tdm_io.sh
Verifying archive integrity... 100% All good.
Uncompressing DSC TDM I/O card installer 100%
This script will install the driver rpm:
iphwaeto-1.14.ribbon-14.x86_64-centos6-2-6-32.rpm
which includes IO image:
rel_11_00_p13.swe.img
If these are not correct, please download the latest version of this script and the rpm.
Press Enter to continue
iphwaeto version installed is already at expected level. Reinstalling...
Preparing... ########################################### [100%]
1:iphwaeto ########################################### [100%]
Could only find 1 card(s) on this system.
Verify this matches the expected number of cards. |
Re-source environment variables:
Run dscvm_io_mgmt utility.
Code Block |
---|
# dscvm_io_mgmt |
Make sure both cards are showing as Unconfigured.
Code Block |
---|
DSC SWe I/O Cards
Index Location PCI Address Status Slot KVM Bridge
----- -------- ----------- ------ ---- ----------
0 0000:04:00.0 0000:05:04.0 Unconfigured NA NA
1 0000:85:00.0 0000:86:04.0 Unconfigured NA NA
Please select a card [0-1] or 'q' to quit: |
Info |
---|
|
The numbers in the above output can differ. |
- Configure the first TDM I/O card.
Select card/Index - 0
Code Block |
---|
Please select a card [0-1] or 'q' to quit: 0 |
Select action - C
Code Block |
---|
DSC SWe I/O Cards
Card 0: pci0 0000:04:00.0 Unconfigured
------------------------
(C)onfigure
(I)nstall Image and Start
(S)top
(R)estart
(U)nconfigure
Boot (F)irmware Debug Access
(A)pplication Debug Access
Please select an action [C,I,S,R,U,F,A], 'b' for back, or 'q' to quit: C |
Enter the root password.
Code Block |
---|
Please enter the root password for the DSC SWe
root@192.168.240.1's password: |
A list of cards is displayed. Enter the slot number 9.
Code Block |
---|
DSC SWe I/O Cards
Card 0: pci0 0000:04:00.0 Unconfigured
------------------------
Please enter a DSC SWe slot number from this list: 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
or 'b' for back, or 'q' to quit: 9 |
Enter HA subnet soft bridge - br2-103
Code Block |
---|
The slot number will be applied when flashing the I/O card image.
Please enter a KVM softswitch, 'NA' to skip, 'b' for back, or 'q' to quit: br2-103 |
Tip |
---|
|
The error "bridge NA does not exist!" is expected. |
Code Block |
---|
bridge NA does not exist!
DSC SWe I/O Cards
Index Location PCI Address Status Slot KVM Bridge
----- -------- ----------- ------ ---- ----------
0 0000:04:00.0 0000:05:04.0 Offline 9 br2-103
1 0000:85:00.0 0000:86:04.0 Unconfigured NA NA
Please select a card [0-1] or 'q' to quit: |
Configure the second TDM I/O card.
Select card/Index - 1
Code Block |
---|
Please select a card [0-1] or 'q' to quit: 1 |
Select action - C
Code Block |
---|
DSC SWe I/O Cards
Card 1: pci1 0000:04:00.0 Offline
------------------------
(C)onfigure
(I)nstall Image and Start
(S)top
(R)estart
(U)nconfigure
Boot (F)irmware Debug Access
(A)pplication Debug Access
Please select an action [C,I,S,R,U,F,A], 'b' for back, or 'q' to quit: C |
Enter the root password.
Code Block |
---|
Please enter the root password for the DSC SWe
root@192.168.240.1's password: |
A list of cards is displayed. Enter the slot number 8.
Code Block |
---|
DSC SWe I/O Cards
Card 1: pci1 0000:85:00.0 Unconfigured
------------------------
Please enter a DSC SWe slot number from this list: 3 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
or 'b' for back, or 'q' to quit: 8 |
Enter HA subnet soft bridge - br2-103
Code Block |
---|
The slot number will be applied when flashing the I/O card image.
Please enter a KVM softswitch, 'NA' to skip, 'b' for back, or 'q' to quit: br2-103 |
Tip |
---|
|
The error "bridge NA does not exist!" is expected. |
Code Block |
---|
HOST2:
DSC SWe I/O Cards
Index Location PCI Address Status Slot KVM Bridge
----- -------- ----------- ------ ---- ----------
0 0000:06:00.0 0000:07:04.0 Offline 9 br2-103
1 0000:85:00.0 0000:86:04.0 Offline 8 br2-103 |
Install Image and start the card.
Info |
---|
|
This following steps require the information for the path to the I/O image on the server. The TDM card will show up as online once this is complete. This procedure takes about 2 to 3 minutes to complete. |
- Install the first TDM card.
Select card/Index - 0
Code Block |
---|
Please select a card [0-1] or 'q' to quit: 0 |
Select action - I
Code Block |
---|
DSC SWe I/O Cards
Card 0: pci0 0000:04:00.0 Offline
------------------------
(C)onfigure
(I)nstall Image and Start
(S)top
(R)estart
(U)nconfigure
Boot (F)irmware Debug Access
(A)pplication Debug Access
Please select an action [C,I,S,R,U,F,A], 'b' for back, or 'q' to quit: I |
Press ENTER.
Code Block |
---|
DSC SWe I/O Cards
Card 0: pci0 0000:04:00.0 Offline DSC Slot 9
------------------------
Please enter a DSC SWe I/O card image file [/opt/ribbon/dsc_io/tools/rel_11_00_p10.swe.img]: <press Enter and wait> |
Select action - b
Code Block |
---|
DSC SWe I/O Cards
Card 0: pci0 0000:04:00.0 Offline
------------------------
(C)onfigure
(I)nstall Image and Start
(S)top
(R)estart
(U)nconfigure
Boot (F)irmware Debug Access
(A)pplication Debug Access
Please select an action [C,I,S,R,U,F,A], 'b' for back, or 'q' to quit: b |
Code Block |
---|
DSC SWe I/O Cards
Index Location PCI Address Status Slot KVM Bridge
----- -------- ----------- ------ ---- ----------
0 0000:04:00.0 0000:05:04.0 Online 9 br2-103
1 0000:85:00.0 0000:86:04.0 Offline 8 br2-103
Please select a card [0-1] or 'q' to quit: |
Install the second TDM card.
Select card/Index - 1
Code Block |
---|
Please select a card [0-1] or 'q' to quit: 1 |
Select action - I
Code Block |
---|
DSC SWe I/O Cards
Card 1: pci1 0000:04:00.0 Online
------------------------
(C)onfigure
(I)nstall Image and Start
(S)top
(R)estart
(U)nconfigure
Boot (F)irmware Debug Access
(A)pplication Debug Access
Please select an action [C,I,S,R,U,F,A], 'b' for back, or 'q' to quit: I |
Press ENTER.
Code Block |
---|
DSC SWe I/O Cards
Card 1: pci1 0000:85:00.0 Offline DSC Slot 8
------------------------
Please enter a DSC SWe I/O card image file [/opt/ribbon/dsc_io/tools/rel_11_00_p10.swe.img]: <press Enter and wait> |
Select action - b
Code Block |
---|
DSC SWe I/O Cards
Card 1: pci1 0000:04:00.0 Online
------------------------
(C)onfigure
(I)nstall Image and Start
(S)top
(R)estart
(U)nconfigure
Boot (F)irmware Debug Access
(A)pplication Debug Access
Please select an action [C,I,S,R,U,F,A], 'b' for back, or 'q' to quit: b |
Code Block |
---|
DSC SWe I/O Cards
Index Location PCI Address Status Slot KVM Bridge
----- -------- ----------- ------ ---- ----------
0 0000:04:00.0 0000:05:04.0 Online 9 br2-103
1 0000:85:00.0 0000:86:04.0 Online 8 br2-103
Please select a card [0-1] or 'q' to quit: |
Stop the dscvm-io service.
Code Block |
---|
# service dscvm-io stop |
Code Block |
---|
Bringing pci0 down
Bringing pci1 down
---------------------------------------------------------
/opt/ribbon/dsc_io/driver/iphwaetodrv 1.09 for Linux (C)Interphase Corp. 2008
iphwaeto driver remove
--------------------------------------------------------- |
Start the dscvm-io service.
Code Block |
---|
# service dscvm-io start |
Code Block |
---|
---------------------------------------------------------
/opt/ribbon/dsc_io/driver/iphwaetodrv 1.09 for Linux (C)Interphase Corp. 2008
iphwaeto driver load
---------------------------------------------------------
Loading PCI network. Success |
Tip |
---|
|
Stopping and Starting the dscvm-io service attaches the PCI device to the bridge configured on the cards. |
Proceed to the appropriate procedure
Install Host Software to Enable TDM FunctionalityCommission the TDM I/O Card with the DSC SWe in the MA-RMS Server.
Access the TDM I/O Card with no DSC SWe in the MA-RMS Server.
Verify for Testing Purposes
Use this procedure to confirm the virtual vSP2000 cards map to the correct physical HOST IO cards.
Start
- Plug a E1 or DS1 loopback plug into one of each of the hosts IO cards (one on HOST1 AND one on HOST2).
- After configuration is completed on the HOSTs and the vSP2K, you will see a port in SYNC with the loop back. Pending this, it will confirm the virtual vSP2K cards map to the correct physical HOST IO cards.
Image RemovedImage Added
Commission the TDM I/O Card with the
in the MA-RMS ServerPrerequisites
- Before you begin this procedure, you must have completed one of the procedures to configure the TDM I/O cards.
Start
If the
is within the MA-RMS server, use the following procedure to commission the TDM I/O card. Tip |
---|
|
Once the TDM is commissioned, you can access the cards from within the by SSH into slot 4 or 5 using the internal IP address 192.168.240.4 or 192.168.240.5, respectively. |
From the Main Menu, select System, and press ENTER.
- Select Software Revisions, and press ENTER.
Select I/O Versions, and press ENTER.
Code Block |
---|
AVAILABLE SOFTWARE VERSIONS
--------------------------------------------------------------------------------
IO (current) PCE382 dsc_vm_19_0_0_nb20200721 OS: rel_11_00_p13.swe.img
IO (current) AMC348 dsc_vm_19_0_0_nb20200721 OS: rel_12_00_p06.x511edge.img
(Servicepack) [none applied]
RUNNING SOFTWARE VERSIONS (*=update required, ?=update unknown)
CARD BUILD SERVICE O/S
-SLOT----TYPE----------RELEASE-VERSION------PACK-----IMAGE-------
--------------------------------------------------------------------------------
Slot 6 IO --TBD-- Not_Available SP: OS: rel_11_00_p13.swe.img
Slot 7 IO --TBD-- Not_Available SP: OS: rel_11_00_p13.swe.img
Slot 8 IO --TBD-- Not_Available SP: OS: rel_11_00_p13.swe.img
Slot 9 IO --TBD-- Not_Available SP: OS: rel_11_00_p13.swe.img
(p=servicepack is partially applied)
No IO cards. To update the IO software stored on the CPU enter 'u'.
Select IO slot number (6 7 8 9) to begin commissioning of individual card(s).
Enter slot # or ENTER to cancel: |
Enter the required slot number, and press ENTER.
Code Block |
---|
|
------------------------------------------------------------------
Commissioning IO card in slot 6...
------------------------------------------------------------------
Enter MA-RMS IP address, host of this IO card:
172.28.1.202
Enter the physical slot location of the TDM card in the RMS server:
4
A Reboot of slot 6 is required to update the TDM RMS config file on the IO card.
Please wait while the card in slot 6 is rebooting ...
connect to host slot6_0: authentication failure.
Software is being uploaded...Waiting
connect to host slot6_0: authentication failure.
Software is being uploaded...Waiting
connect to host slot6_0: authentication failure.
Software is being uploaded...Waiting
connect to host slot6_0: authentication failure.
Software is being uploaded...Waiting
Software is being uploaded...Waiting
Software is being uploaded...Waiting
Software is being uploaded...Waiting
Software is being uploaded...Waiting
Software is being uploaded...Waiting
Software is being uploaded...Waiting
Software is being uploaded...Waiting
Software is being uploaded...Waiting
Starting applications...
/opt/io_ss7gw/current/bin/sysmon.default -p /opt/io_ss7gw/current/scripts -s /opt/io_ss7gw/current/scripts
/opt/io_ss7gw/current/bin/sysmon.cpucheck -p /opt/io_ss7gw/current/scripts -s /opt/io_ss7gw/current/scripts -c /opt/io_ss7gw/current/scripts/cpuusagethresh
/opt/io_ss7gw/current/bin/sysmon.diskmon -p /opt/io_ss7gw/current/scripts -s /opt/io_ss7gw/current/scripts
/opt/io_ss7gw/current/bin/sysmon.logmem -p /opt/io_ss7gw/current/scripts -s /opt/io_ss7gw/current/scripts -m /opt/io_ss7gw/current/scripts/memfreethresh
/opt/io_ss7gw/current/bin/sysmon.slotinventory -p /opt/io_ss7gw/current/scripts -s /opt/io_ss7gw/current/scripts
IO card in slot 6 is commissioned and ready for use...
INFO: Now the system has an IO card
Starting the sysmon.configaudit process on slot 1.
INFO: Also starting the sysmon.configaudit process on slot 2.
Note: flex_slot.conf file doesn't exist ... This is ok if the SDA is not configured on the system.
Software Update for IO Card in Slot #6
Determining running and current software version. Please wait...
Running on IO (slot6_0):
-Load: dsc_vm_19_0_0_nb20200721
-OS: rel_11_00_p13.swe.img
Current IO version (on MGMT VM):
-Load: dsc_vm_19_0_0_nb20200721
-OS: rel_11_00_p13.swe.img
-Servicepack: [none applied]
No software change to perform.
'd' - Decommission this IO card to prepare it for removal.
Select action to take, or any other key to cancel: |
- Press ENTER to continue.
- Repeat steps 1 to 6 for the 3 other I/O cards that are running the same software load as the Management CPUs.
Navigate to the Available Software Versions screen and confirm that the card(s) is commissioned as required.
Code Block |
---|
AVAILABLE SOFTWARE VERSIONS
--------------------------------------------------------------------------------
IO (current) PCE382 dsc_vm_19_0_0_nb20201005 OS: rel_11_00_p13.swe.img
IO (current) AMC348 dsc_vm_19_0_0_nb20201005 OS: rel_12_00_p06.x511edge.img
(Servicepack) [none applied]
IO (prev) PCE382 dsc_vm_19_0_0_nb20200721 OS: rel_11_00_p13.swe.img
IO (prev) AMC348 dsc_vm_19_0_0_nb20200721 OS: rel_12_00_p06.x511edge.img
(Servicepack)
RUNNING SOFTWARE VERSIONS (*=update required, ?=update unknown)
CARD BUILD SERVICE O/S
-SLOT----TYPE----------RELEASE-VERSION------PACK-----IMAGE-------
--------------------------------------------------------------------------------
Slot 6 IO PCE382 19.0.0 (nb20201005) SP: OS: rel_11_00_p13.swe.img
Slot 7 IO PCE382 19.0.0 (nb20201005) SP: OS: rel_11_00_p13.swe.img
Slot 8 IO PCE382 19.0.0 (nb20201005) SP: OS: rel_11_00_p13.swe.img
Slot 9 IO PCE382 19.0.0 (nb20201005) SP: OS: rel_11_00_p13.swe.img
(p=servicepack is partially applied)
Select IO slot number (6 7 8 9) to begin upgrade
or decommissioning of individual card(s). |
Consider doing a complete system backup (using a USB key). For more information, refer to Complete System Backup for DSC 8000.
Access the TDM I/O card with No in the MA-RMS ServerPrerequisites
- Before you begin this procedure, you must have completed one of the procedures to configure the TDM I/O Cards.
Start
If there is no
within the MA-RMS server, access the cards from the server by assigning IP 192.168.240.30 to the br2-103 HA bridge.Add the IP address and the Netmask to the /etc/sysconfig/network-scripts/ifcfg-br2-103 file.
Code Block |
---|
# vi /etc/sysconfig/network-scripts/ifcfg-br2-103
# Interface managed by CCM
DEVICE=br2-103
TYPE=Bridge
IPV6_AUTOCONF=no
ONBOOT=yes
PEERDNS=yes
USERCTL=no
HOTPLUG=no
BOOTPROTO=none
IPADDR=192.168.240.30
NETMASK=255.255.254.0 |
Restart the network services by issuing the command.
Code Block |
---|
# service network restart |
Verify the IP is assigned properly.
Code Block |
---|
# ip addr show br2-103 |
Code Block |
---|
27: br2-103: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN
link/ether 00:20:00:22:65:00 brd ff:ff:ff:ff:ff:ff
inet 192.168.240.30/23 brd 192.168.241.255 scope global br2-103
inet6 fe80::220:ff:fe22:6500/64 scope link
valid_lft forever preferred_lft forever |
Ping the first TDM card
Code Block |
---|
# ping 192.168.240.4 |
Code Block |
---|
PING 192.168.240.4 (192.168.240.30) 56(84) bytes of data.
64 bytes from 192.168.240.30: icmp_seq=1 ttl=64 time=10.1 ms
64 bytes from 192.168.240.30: icmp_seq=2 ttl=64 time=0.752 ms
^C
--- 192.168.240.4 ping statistics ---
2 packets transmitted, 2 received, 0% packet loss, time 1294ms
rtt min/avg/max/mdev = 0.752/5.455/10.158/4.703 ms |
Tip |
---|
|
The Ping test can be repeated for any other TDM card within the same network. |
Configure the MTP2 SCTP Server Primary IP
Prerequisites
- Before you begin this procedure, you must have completed one of the procedures to configure the TDM I/O cards
Start
- In the Configuration Management UI (CMU), under Applications, select Hardware.
- Select the IO card.
- Under IO Manager selection, select the Card Type.
- Under the SCTP Server selection, click ATM.
Populate the Primary IP. For example, 192.168.240.4
Info |
---|
Use the base IP of 192.168.240 plus x = the slot position of the IO card. For example, 192.168.240.4 for an IO in slot 4. |
Click Continue.
- Repeat steps 4-6 for TDM.
...