Versions Compared

Old Version 2

changes.mady.by.user Ribbon Communications

Saved on

compared with

New Version 3

changes.mady.by.user Ribbon Communications

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

Add_workflow_for_techpubs
AUTH1UserResourceIdentifier{userKey=8a00a0c86e9b2550016ec54396b5000a, userName='null'}
JIRAIDAUTHSBX-112200117394
REV5UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26cb8305e9, userName='null'}
REV6UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26cb8305e9, userName='null'}
REV3UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26c9b802fd8a00a0c8694149ce01694dd6a1440008, userName='null'}
REV1UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26c8c601868a00a02355cd1c2f0155cd26ccfa092d, userName='null'}


Panel

In this section:

Table of Contents



Info
iconfalse

Related articles:


Use the SIP JJ9030Interworking Profile window to configure SIP JJ9030 Interworking profiles which contain parameters needed for SIP JJ9030 Interworking. For information on other related profiles for SIP-ISUP and interworking between different SIP variants, refer to Support for SIP-ISUP.

Multiexcerpt
MultiExcerptNamePrivate Header for ISDN 64K Unrestricted

Available_since
TypeAvailable Since
Release10.1.2

Private Header for ISDN 64K Unrestricted

The SBC supports the ISUP signal transfer using the Japanese unique private header "P-N-ISUP-R" between the NNI-GWs. The private header "P-N-ISUP-R" carries the ISUP message-specific information in the SIP message. "P-N-ISUP-R" is required for 64K unrestricted and voice calls. The SBC converts P-N-ISUP-R header contents to ISUP parameters in the SIP-T MIME. Additionally, the SBC creates P-N-ISUP-R header based on the ISUP parameter received in the SIP-T MIME. The SBC uses the following configuration for SIP-T to SIP (JJ-90.30) calls during interworking with the P-N-ISUP-R header.

The SBC adds the parameter pnisuprHeaderInterworking inside the SIP-JJ-90-30 Interworking profile. This parameter is used only if sipFlavor is JJ9030".

The SBC adds the parameter siptOriginatingCarrierCodesForPniusprIwk inside the SIP-JJ-90-30 Interworking profile to configure multiple originating carrier codes.

  • "Originating Carrier Code" is 4 digits.
  • Maximum number of originating carrier codes are 50.
  • This configuration is available only if the sipFlavor is SIP-T.

Note: This configuration mentions all of the supported originating carriers on the SIP-T side.

The list of ISUP parameters and messages supported in the P-N-ISUP-R header are shown below.

Message Type/ISUP Parameter

ISUP Message

IAM

ACM

CPG

ANM

REL

Message Type (0x00)

M

M

M

M

M

Forward Call Indicators (0x07)

M

-

-

-

-

Transmission Medium Requirement (0x02)

M

-

-

-

-

Event Information (0x24)

-

-

M

-

-

Backward Call Indicators (0x11)

-

M

O

O

－

Cause Indicators (0x12)

-

O

O

-

V

User Service Information (0x1d)

O

-

-

-

-

Access Transport (0x03)

O

O

O

O

-

Optional Backward Call Indicators (0x29)

-

O

O

O

-

User-to-User Indicator (0x2A)

-

O

O

-

-

M= Mandatory

O= Optional

V= Mandatory variable


To View SIP JJ9030 Interworking Profiles

On the SBC main screen, navigate to All → Profiles → Signaling → SIP JJ9030Interworking Profile.

The SIP JJ9030Interworking Profile window opens:

Caption0

Figure

1

SIP

:  SIP JJ9030Interworking Profile Window

Image Modified

To Create a SIP JJ9030 Interworking Profile

To create a new SIP JJ9030 Interworking Profile:

  1. Click New SIP JJ9030 Interworking Profile. The Create New SIP JJ9030Interworking Profile window opens.

    Caption0Figure1

    Figure 2: Create New SIP JJ9030Interworking Profile Window

    Image Modified

  2. Use the following table to configure the parameters and then click Save.

Caption0

  1. Table

  1. 1

  1. : SIP JJ9030 Interworking Profile Parameters

    FieldLength/RangeDescription
Name1-23 characters

The name of this SIP JJ-90.30 Interworking Profile.

NOTE: You can configure a maximum of 32 SIP JJ9030 Interworking Profiles.

SIP FlavorN/A

The type of SIP parameters and procedures used for this interworking profile.

  • JJ9030
  • SIP-T
    1. Add User Equal Phonefor Div Hi InterworkingN/A

      Enable this parameter to add "user=phone" and the "mp" parameter for Diversion History Info Interworking.

      • Disabled (default)
      • Enabled
      BCI Called Party CategoryN/A

      The Backwards Call Indicators Called Party Category.

      • No Indication
      • Ordinary
      • Payphone
      • Spare

      NOTE: This parameter is mandatory when the parameter SIP Flavor is set to SIP-ttc-charging-params.

      BCI Charge IndicatorN/A

      The Backwards Call Indicators Charge Indicator.

      • Charge
      • No Charge
      • No Indication
      • Spare

      NOTE: This parameter is mandatory when the parameter SIP Flavor is set to SIP-ttc-charging-params.

      BCI Terminating ISDN AccessN/A

      The Backwards Call Indicators Terminating ISDN Access Indicator.

      • Non ISDN
      • Isdn

      NOTE: This parameter is mandatory when the parameter SIP Flavor is set to

    1. SIP-ttc-charging-params

  • X-Header

    1. .

      Charge Area Information5 digits (0-9)The Charge Area Information, consisting of 5 digits (0-9).
      Name
    Orig Ioi
    1. 1-
    128
    1. 23 characters

      The name

    of the Originating Inter Operator Identifier.Term

    1. of this SIP JJ-90.30 Interworking Profile.

      NOTE: You can configure a maximum of 32 SIP JJ9030 Interworking Profiles.

      Orig Ioi1-128 charactersThe name of the
    Terminating Add User Equal Phonefor Div Hi
    1. Originating Inter Operator Identifier.
      Originating Carrier Code4 digits (0-9)

      The Originating Carrier Code, consisting of 4 digits (0-9).

      NOTE: This parameter is mandatory when the parameter SIP Flavor is set to JJ9030.

    Terminating Carrier Code4 digits (0-9)

    The Originating Carrier Code, consisting of 4 digits (0-9).

    Charge Area Information5 digits (0-9)The Charge Area Information, consisting of 5 digits (0-9).
    1. Pnisupr Header InterworkingN/A

      Enable this

    parameter to add "user=phone" and the "mp" parameter for Diversion History Info Interworking

    1. flag on SIP JJ9030 leg to support P-N-ISUP-R header interworking in SIP-T to SIP JJ90.30 and SIP JJ90.30 to SIP-T calls.

      • Disabled (default)
      • Enabled
      Set Hi Presentation RestrictedN/A

      Set Presentation Indicator as "restricted" for History Info Interworking.

      • Disabled (default)
      • Enabled
    BCI Charge Indicator
    1. SIP FlavorN/A

      The

    Backwards Call Indicators Charge Indicator.
    • Charge
    • No Charge
    • No Indication
    • Spare

    1. type of SIP parameters and procedures used for this interworking profile.

      • JJ9030
      • SIP-T
      • SIP
    NOTE: This parameter is mandatory when the parameter SIP Flavor is set to SIP
      • -ttc-charging-params
    .BCI Called Party CategoryN/A

    The Backwards Call Indicators Called Party Category.

    • No Indication
    • Ordinary
    • Payphone
    • Spare

    NOTE: This parameter is mandatory when the parameter SIP Flavor is set to SIP-ttc-charging-params.

      • X-Header
      Sipt Originating Carrier Codes For Pnisupr IwkA list of 4-digit carrier codes,
      up to 50 elements

      List of supported originating carrier codes on the SIP-T leg for the P-N-ISUP-R header interworking in a SIP-T to SIP JJ9030 call.

      Note: You can separate the "sipt Originating Carrier Codes For Pnisupr Iwk" field values using comma. For example: 1234,1235,1236 and so on.

      Term Ioi1-128 charactersThe name of the Terminating Inter Operator Identifier.
      Terminating Carrier Code4 digits (0-9)

      The Originating Carrier Code, consisting of 4 digits (0-9)

    BCI Terminating ISDN AccessN/A

    The Backwards Call Indicators Terminating ISDN Access Indicator.

    • Non ISDN
    • Isdn
    NOTE: This parameter is mandatory when the parameter SIP Flavor is set to SIP-ttc-charging-params

    1. .

      Transit PcvN/A

      When enabled, the SBC transits icid-value, orig-ioi and term-ioi of P-Charging-Vector transparently in JJ90.30 to JJ90.30 calls, using the current trunk group.

      • Disabled (default)
      • Enabled

      Note:

      Transit Icid In InviteN/A

      When enabled, the SBC transits the icid-value in P-Charging-Vector transparently in the INVITE sent on the current trunk for JJ90.30 to JJ90.30 calls.

      • Disabled (default)
      • Enabled

      Note:


    To Edit a SIP JJ9030 Interworking Profile

    To edit a SIP JJ9030 Interworking Profile:

    1. Click the radio button adjacent to the name of the SIP JJ9030 Interworking Profile you want to edit. The Edit Selected SIP JJ9030 Interworking Profile window opens.
    2. Make any required changes to the profile and click Save.

    To Copy a SIP JJ9030 Interworking Profile

    To copy a SIP JJ9030 Interworking Profile:

    1. Click the radio button adjacent to the name of the  SIP JJ9030 Interworking Profile you want to copy.
    2. Click Copy SIP JJ9030 Interworking Profile. The Copy Selected SIP JJ9030 Interworking Profile window opens.
    3. Make any required changes to the profile and click Save.

    To Delete a SIP JJ9030 Interworking Profile

    To delete a SIP JJ9030 Interworking Profile:

    1. Click the radio button adjacent to the name of the  SIP JJ9030 Interworking Profile you want to delete.
    2. Click the delete icon (X) at the end of the row.
    3. Confirm the deletion when prompted.
    Info
    titleNote

    If a SIP JJ9030 Interworking Profile is associated with a SIP trunk group, remove it from the trunk group before deleting it.

    pagebreak