Versions Compared

Old Version 5

changes.mady.by.user Ribbon Communications

Saved on

compared with

New Version Current

changes.mady.by.user Ribbon Communications

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.


Panel

In this section:

Table of Contents
maxLevel2



Info
iconfalse

Related articles:

Children Display



 

This object specifies a Network Time Protocol (NTP) server that supplies local time to the 

Spacevars
0product
. The reference time delivered by NTP is the source of all timestamps placed into the accounting records.

During the installation process, the NTP server and time zone information is input to the Active server only. Once the Standby server starts, this information is synced from the Active to Standby.

Note
iconfalse
titleNote
The 
Spacevars
0product
should receive an initial time synchronization from NTP server before accepting calls.

Include Page
NTP_server_limit
NTP_server_limit

Command Syntax

The following CLI syntax is used to configure NTP server at system level.

application, and thus cause a service outage for a few minutes. 
Code Block
languagenone
% set system ntp
	keys <key Id>
		keyType <MD5 | SHA1>
		keyValue <key value>
	serverAdmin <IP_address>
		authKey <key Id>
		maxPoll <10-17>
		minPoll <4-17>
		state <disabled | enabled>
		version <version3 | version4>
	timeZone <SYSTEM NAME>
		zone <zone>
Warning
titleWarning
Changing the time zone forces a restart of the 
 Spacevars
0product
 Spacevars
0company
 recommends changing the time zone only during a system maintenance window. Refer to Changing the Time Zone for details.

Command Parameters
 Div
classpdf6pttext

 Caption
0Table
1NTP Services Management parameters

Parameter
Length/Range
Description
keys 
 N/A
<key Id> – NTP authentication key Identifier to obtain from NTP server, with following attributes:
  • keyType – NTP authentication key type to assign to the SBC for this <keyId>:
    • MD5 – MD-5 (Message Digest Algorithm) cryptographic hash function.
    • SHA1 – SHA-1 (Secure Hash Algorithm) cryptographic hash function.
  • keyValue <key value> – NTP authentication key value to assign to the SBC for this <keyId>.
serverAdmin
N/A
<ip_address> – The NTP server IP address.
  • authKey <key Id> – NTP authentication key to authenticate the server (Use NTP server <keyId> configured in keys command).
  • maxPoll – The maximum poll interval, in seconds to the power of 2, for this NTP Server. The maxPoll parameter value range is 10 - 17 (1,024 seconds to 36.4 hours). (range: 10-17 / default = 10).
  • minPoll – The minimum poll interval, in seconds to the power of 2, for this NTP Server. The minPoll parameter value range is 4 - 17 (16 seconds to 36.4 hours). (range: 4-17 / default = 4).
  • state– NTP server state.
    • disabled – (default) The state of the NTP server is disabled.
    • enabled – The state of the NTP server is enabled.
Warning: Enabling the NTP will reset your system. You can cancel the action if you do not want to reset the system.
  • version– NTP server version.
    • version3 (default)
    • version4
timeZone
N/A
Time zone configuration.
  • <system_name> – 
     Spacevars
    0product
     system name.
  • zone – Specify the time zone where the node resides. Refer to Time Zones page.


Command Example
The following example enables NTP server version 4 at IP address 10.20.30.40, and sets time zone of the 
 Spacevars
0product
 system to U.S. Hawaii time.
 Code Block
languagenone
% set system ntp serverAdmin 10.20.30.40 version version4  
% set system ntp serverAdmin 10.20.30.40 state enabled
% set system ntp serverAdmin 10.1.1.1 authKey 6 
% set system ntp timeZone SBC01 zone us-Samoa
% show system ntp
timeZone SBC01 {
    zone us-Samoa;
}
serverAdmin 10.160.20.53 {
    version version4;
    minPoll 4;
    maxPoll 10;
    state   enabled;
    authKey 6;
}
pagebreak