Add_workflow_for_techpubs | ||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
|
Panel | ||||
---|---|---|---|---|
In this section:
|
SBC SWe deployments support a domain-based licensing model referred to as network-wide domain licensing (NWDL). In contrast to node-locked licensing, a domain license is tied to an administrative domain rather than the hardware ID for a specific host server or the UUID for a specific node instance. A domain license is bound to the domain through public/private key-pairing and it defines the features and capacity allowed for all nodes within the domain. NWDL provides flexibility in cloud environments where the number and placement of nodes sometimes varies. Contact your Ribbon representative for more information on available licensing options and to complete the ordering process that is required prior to implementing NWDL.
title | Note |
---|
The NWDL license model is supported on the following virtual/cloud platforms.
NWDL
license model is currently not supported on hardware SBC platforms (5400/7000).
NWDL is implemented using license management capabilities within the Insight Element Management System (EMS). The EMS provides the public key used to bind the license to the local domain and is used for associating license data with eligible nodes. The basic steps to implement domain licensing are as follows:
Refer to the License Management section in EMS documentation for specific procedures to locate and copy the public key, install a license bundle, and associate feature licenses with SBC nodes.
After these preparations are completed on the EMS, enable domain-based licensing on the SBC cluster by configuring the license mode as "domain." Save and activate the configuration. The OAM node for the cluster provides the configuration update to each SBC node in the cluster. The nodes then enable or disable features based on the license definition in their configuration.
Info | ||||
---|---|---|---|---|
| ||||
The NWDL license bundle must be added to the SBC cluster configuration before or at the same time you change the license mode to "domain." Changing license mode to domain on an active system without an NWDL license bundle installed will result in a service outage. |
Info | ||||
---|---|---|---|---|
| ||||
If you push the count-based license, the "show table system licenseInfo" table displays "USAGE LIMIT" as 999999. |
Info | ||||
---|---|---|---|---|
| ||||
The in-use column does not increment for the active sessions if the license type is ON/OFF. |
In domain licensing mode, you can add to your existing license definition following the same process to load another license bundle file onto the EMS, and using the EMS to assign the additional features licenses to the SBC clusters. The resulting set of licenses features and capacity for the cluster is the aggregate of the existing license and the added license.
When configured for NWDL, the SBC supports a "full-capacity" option in which the counts for individual, counted license features are no longer used to limit activity on the SBC. Enabling the full-capacity feature effectively enables feature use up to the capacity of the node. Actual license usage is reported to Ribbon using EMS statistics.
The full-capacity feature requires the SBC-CAPACITY-D license key in the license file. Contact your Ribbon representative for more information on the use of the full-capacity licensing option.
Info | ||
---|---|---|
| ||
The NWDL architecture permits the nodes to burst to capacity when the "D" feature ID is present (SBC-RTU-D). |
Info | ||
---|---|---|
| ||
If the License SBC-CAPACITY-D is present, the SBC does not need to register with the License Manager. |
Use the SBC CLI or access the SBC Configuration Manager UI from the EMS to enable domain license mode and optionally specify license capacity limits for the nodes in the cluster. Refer to Modifying SBC Cluster Configuration.
Note | ||
---|---|---|
| ||
To avoid a service outage, ensure your NWDL licenses are already installed if you reconfigure an SBC cluster into domain license mode. |
By default, SBC license mode is set to nodeLocked
. Use the following CLI commands to place the SBC in domain (NWDL) license mode:
Code Block | ||
---|---|---|
| ||
% set system licenseMode mode domain % commit |
Or, in the SBC Configuration Manager UI:
Use the following command to output information on the domain license bundles loaded into the system.
Code Block | ||
---|---|---|
| ||
> show table system licenseDomainBundleInfo |
Or, in the SBC Configuration Manager UI:
Go to All > System > License Domain Bundle Info The License Domain Bundle Info window opens.
The following license information is output:
activeLicenseMode
– The licensing mode currently in use by the SBCbundleName
– License bundle nameexpirationDate
– License expiration datefeatureName
– license keys for each licensed featuregenerationDate
– The date the license was generatedinstallDate
– The date the license was installedlicenseId
– License IDlineId
– The line ID for the license feature entrypurchaseOrderId
– The purchase order ID specified when the license was generatedusageLimit
– Usage limit for the licensed featurePagebreak |
---|