Page History

...

1. Download the SBC application package from the Ribbon Support Portal to your local folder on a PC or remote server. Refer to Downloading Software from the Ribbon Support Portal.
2. Validate the SBC md5 checksum using the checksum calculator. Refer to Validating MD5Sum with Checksums Calculator for guidance.

3. Launch EMA.

4. Navigate to Monitoring > Dashboard > System and Software Info to verify the software and HA peer status for both active and standby servers.

   Caption
   0 Figure 1 System and Software Info Screen for Active Server

   
   

   Caption
   0 Figure 1 System and Software Info Screen for Standby Server

   
   

5. Navigate to Administration > System Administration > File Upload to upload the SBC application package to the active and standby SBC servers.
   
   

   1. Click the File Upload tab.

      caption

      0	Figure
      1	File Upload Screen

      Image Removed

   2. Click Add Files to Queue.

   3. Browse for the SBC application package files in the File Upload screen and then click Open.  

      Caption0Figure1

      Selecting SBC application package

      Image Removed

        

   4. The files are listed in the Upload Queue section. Click Upload All Files. The file upload starts.

      Caption

      0	Figure
      1	Files on SBC

       Image Removed

   5. Repeat steps "a" through "e" for  the standby SBC server.
      
      

6. Stop the application on the active server using Administration > System Administration > Platform Management > Stop SBC Application.
   Stopping the application is a service-affecting operation.

   Caption
   0 Figure 1 Stopping SBC Application in Active Server

   
   

7. Click OK to continue the stop operation.

   Caption
   0 Figure 1 Confirming Stop SBC Application

   The application stops on the active server.

8. Launch the EMA Platform Mode on the standby server.

   Info
   title Note
   Once the active server (WFDSBC01a) is stopped, the standby server (WFDSBC01b) automatically becomes active.

   
   

9. Stop the application on the standby server using Administration > System Administration > Platform Management > Stop SBC Application.
   Stopping the application is a service-affecting operation.

   Caption
   0 Figure 1 Stopping SBC Application on Standby Server

   
   

10. Click OK to continue the stop operation.

    Caption
    0 Figure 1 Confirming Stop Application

    The application stops on the standby server.

    Caption
    0 Figure 1 Application Stopped on Standby Server

    
    

    Info
    title Note
    If you are upgrading an SBC SWe deployment, before starting the upgrade of the active instance, shut down or power-off the standby instance from the host.

    
    

11. From the EMA of the initial active server (WFDSBC01a), navigate to Administration > System Administration > Software Install/Upgrade.

12. Select the SBC Package Name to upgrade, and click Standalone Software Upgrade.

    Info
    title Note
    Because you are performing a non-LSWU upgrade and both the active and standby SBCs are down, it is considered a standalone upgrade even for an HA pair.

    
    

    Caption
    0 Figure 1 Selecting SBC Package

     The signature file of the SBC package verifies the integrity of the package contents before proceeding with the SBC installation.

    Caption
    0 Figure 1 Verifiying Package Integrity

    
    

13. Click Start Upgrade.

    Caption
    0 Figure 1 Selecting Offline Upgrade

     The upgrade process starts on the active server (WFDSBC01a) and displays the upgrade status in the Upgrade Log section.

    Caption
    0 Figure 1 Performing pre-install checks and DB install

    
    

    Info
    title Note
    You may lose connectivity to the browser session when the server reboots.

    
    

    Info
    title Note
    This process takes approximately 45 minutes to complete on a single server.

    
    

    Warning
    Once the upgrade is successful, clear the browser cache prior to accessing the SBC EMA.

    
    

14. Log on to EMA using the default credentials.

    Caption
    0 Figure 1 Logging On to EMA Platform

    
    

    Caption
    0 Figure 1 Logging On to EMA Platform

    
    

15. Verify the SBC installation status on the Administration > System Administration > Software Install/Upgrade screen.

    Caption
    0 Figure 1 Continuing the SBC Upgrade

    Wait until the SBC upgrade is complete.
    
    

16. Verify the SBC application status on the Administration > System Administration > Platform Management screen.

    Caption
    0 Figure 1 Verifying Active SBC Status

    
    

    Info
    title Note
    Once all the SBC processes start running, continue upgrading the standby SBC server.

    
    

    Note
    If upgrading your SBC from a release prior to 7.1.x, stop the application on the active server using Administration > System Administration > Platform Management > Stop SBC Application before proceeding to the next step.

    
    

17. Follow steps 11 through 16 to perform an upgrade on the standby server (WFDSBC01b).

    Info
    title Note
    If you are upgrading an SBC SWe deployment, power-on the standby instance from the host before returning to step 11.

    
    

18. Verify the SBC application status on the Administration > System Administration > Platform Management screen.

    Caption
    0 Figure 1 Verifying Standby SBC Status

    
    

19. Verify the firmware, ConnexIP OS and SBC application versions in Monitoring > Dashboard > System and Software Info.

    Caption
    0 Figure 1 System and Software Information for Active Server

    
    

    Caption
    0 Figure 1 System and Software Information for Standby Server

    
    

20. Verify the system sync status is in Sync Completed state in All > System > Sync Status.

    Caption
    0 Figure 1 System Sync Status

    
    

    Pagebreak