...
On the SBC main screen, go to Configuration > System Provisioning > Category: CAC Provisioning > Zone > CAC > Ingress. The Ingress window is displayed. Ingress or
All > Address Context > Zone > CAC > Ingress
Use the drop-down
...
lists to select
...
an Address Context
...
and Zone.
...
| Caption |
|---|
| 0 | Figure |
|---|
| 1 | CAC Provisioning - Zone - CAC - Ingress Window |
|---|
|
 Image Removed
Note: An example dialog box is shown here. Refer to the table below for model-specific allowed values. |
 Image Added
|
| Include Page |
|---|
| _Subscribe_CAC_Access_Restriction |
|---|
| _Subscribe_CAC_Access_Restriction |
|---|
|
Use the following table to configure the parameters and then click Save.
| Caption |
|---|
| 0 | Table |
|---|
| 1 | Zone - CAC - Ingress Parameters |
|---|
| 3 | Zone - CAC - Ingress Parameters |
|---|
|
Parameter
|
Description
|
|---|
| Call Limit | Specifies the total number of calls allowed for Ingressingress. The value ranges from 0 to 2147483647 or unlimited. | | Emergency Oversubscription | Specifies the oversubscription of resources (as a percentage) that is allowed for emergency calls. The value ranges from 0 to 1000 and the default value is 10. | | Extended Emergency IP Limit | The resource oversubscription (expressed as numeric value) allowed for emergency calls. The value ranges from 0 to 40000 with a default value of 0. | | Call Rate Max | Specifies the value of maximum maximum allowed burst sustained rate in calls/second (above the allowed sustained rate) for egress for ingress call attempts. SBC 5xx0 / 5400 / SWe - Range: 1-450, or unlimited. (The default value is unlimited.) SBC 7000 - Range: 1-1,350, or unlimited. (The default value is unlimited.) Note: You can set both “callBurstMax” and “CallRateMax” set both Call Burst Max and Call Rate Max as unlimited; however, if you assign a value to one parameter, the other must also be assigned a value. | | Call Burst Max | Specifies the value of maximum allowed burst (above the allowed sustained rate) for egress ingress call attempts in calls/second. SBC 5xx0 / 5400 /SWe - Range: 1-900, or unlimited. (The default value is unlimited.) SBC 7000 - Range: 1-2,700, or unlimited. (The default value is unlimited.) Note: You can set both “callBurstMax” and “CallRateMax” You can set both Call Burst Max and Call Rate Max as unlimited; however, if you assign a value to one parameter, the other must also be assigned a value. | | Register Rate Max | Specifies the maximum allowed sustained ingress rate (registrations per second) for initial SIP registrations. (range: 1-1000, or unlimited 5000 series; 1-1500, or unlimited for SBC 5400; 1-3000, or unlimited for SBC 7000 series). The default value is unlimited. | Available_since |
|---|
| Type | Modified For |
|---|
| Release | 9.2.1 |
|---|
|
| | Register Burst Max | Specifies the maximum allowed ingress burst (above the allowed sustained rate) for initial SIP registrations. (range: 1-1000, or unlimited 5000 series; 1-1500, or unlimited for SBC 5400; 1-3000, or unlimited for SBC 7000 series). The default value is unlimited. | Available_since |
|---|
| Type | Modified For |
|---|
| Release | 9.2.1 |
|---|
|
| | Packet Rate Max | Specifies the maximum sustained packet rate allowed (in packets/second). (range: 1-65535, or unlimited). Default: unlimited. | | Hpc Oversubscription | Specifies the over-subscription of the resources (in a percentage) that is allowed for HPC calls. When the baseline call limit and bandwidth limits are reached, normal calls are not admitted, but additional HPC calls are allowed up to the configured value percentage. The value ranges from 0 to 100 % and the default value is 10 %. |
|
...