Versions Compared

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.


Panel

In this section:

Table of Contents
maxLevel4


Zone CAC

Use the zone CAC parameters to configure call admission control (CAC) settings for a zone on ingress, on egress, and for the zone as a whole.

Command Syntax

Include Page
Param_values_exception
Param_values_exception

Code Block
languagenone
% set addressContext <addressContext_name> zone <zone_name> cac 
	bandwidthLimit <0-2147483647, or unlimited>
	bandwidthLimitThreshold <0-100>
	bandwidthVideoThreshold <0-100>
	callLimit <0-2147483647, or unlimited>
	callLimitThreshold <0-100>
	egress 
	emergencyOversubscription <0-1000>
	extendedEmergencyIpLimit <0-40000>
	hpcOversubscription <0-100>
	ingress
	registrationLimit <0-2147483647, or unlimited>

 

Include Page
_Subscribe_CAC_Access_Restriction
_Subscribe_CAC_Access_Restriction

Command Parameters

Caption0Table

1

Zone

CAC

Parameters

The name of the zone. You can configure signaling, media, and control for a zone in the address context.

Zone name is unique across all address contexts.

Parameter

Length/Range

Description

zone

1-23

Note

cacN/A

Call Admission Control (CAC) parameters for all peers using this zone.

bandwidthLimit0-2147483647, or unlimitedTotal bandwidth limit in Kbps/sec.
bandwidthLimitThreshold0-100Bandwidth utilization notification threshold, as a percentage. (default = 0)
bandwidthVideoThreshold0-100

Enter threshold value (as a percentage of video bandwidth) to limit video streams to a specific bandwidth to prevent video calls consuming call bandwidth otherwise needed for audio calls. (default = 0)

callLimit0-2147483647, or unlimitedTotal number of calls allowed on this zone. (default = 'unlimited')
callLimitThreshold0-100Call limit utilization notification threshold, as a percentage. (default = 0)
egressN/AEgress-specific call admission control configuration. See the Egress Parameters table below for details.
emergencyOversubscription0-1000, or unlimitedThis parameter gives priority treatment to emergency calls by specifying the resource over-subscription percentage allowed for emergency calls, and represents the allowed percentage of emergency calls beyond the configured call limit. When the call limit is reached, normal calls are rejected but emergency calls are accepted up to an expanded limit. (default = 10)
extendedEmergencyIpLimit0-40000Additional number of emergency calls (expressed as a numeric value) allowed if call limit and emergency over-subscription quota are exhausted. (default = 0)
hpcOversubscription0-100This parameter specifies the amount of resource over-subscription (as a percentage) allowed for HPC calls. When the baseline call limit and bandwidth limit are reached, normal calls are not admitted, but additional HPC calls are allowed up to the configured percentage value. (default = 10)

ingress

N/A

Ingress-specific call admission control configuration. See the Ingress Parameters table below for details.

registrationLimit0-2147483647, or unlimitedThe number of concurrent registrations allowed in this zone. (default = 'unlimited')


Egress

Command Syntax

Code Block
languagenone
% set addressContext <addressContext_name> zone <zone_name> cac egress 
		callBurstMax <1-900, or unlimited> (SBC 7000 range is 1-2700)
		callLimit <0-2147483647, or unlimited>
		callRateMax <1-450, or unlimited> (SBC 7000 range is 1-1350)
		emergencyOversubscription <0-1000>
		extendedEmergencyIpLimit <0-40000>
		hpcOversubscription <0-100>
		registerBurstMax <1-200,3000 or unlimited> (SBC 7000 range is 1-600)
		1-1000 or unlimited for SBC 5xx0; 1-1500 or unlimited for SBC 5400; 1-3000 or unlimited for SBC 7000)
        registerRateMax <1-100,3000 or unlimited> (1-1000 or unlimited for SBC 7000 range is 1-300 5xx0; 1-1500 or unlimited for SBC 5400; 1-3000 or unlimited for SBC 7000)

Command Parameters

caption1
Anchor
0Table
Egress Parameters
Egress Parameters
3

Egress Parameters

NoteYou can

set both

set both callRateMax and callBurstMax as

“unlimited”

"unlimited"; however, if you assign a value to one parameter, the other must also be assigned a value.

value is unlimited. 

ParameterLength/RangeDescription
callBurstMax

SBC 5000:
1-900, or unlimited.

SBC 7000:
1-2700, or unlimited

Maximum allowed burst (above the allowed sustained rate) for egress call attempts, in calls/second. (default = 'unlimited')
callLimit0-2147483647, or unlimitedTotal number of outbound concurrent calls allowed. (default = 'unlimited' )
callRateMax

SBC 5000:
1-450, or unlimited.

SBC 7000:
1-1350, or unlimited

Maximum sustained egress call rate allowed in calls/second. (default = 'unlimited' )

Note
emergencyOversubscription0-1000Over-subscription of resources (as a percentage) allowed for emergency calls. (default = 10)
extendedEmergencyIpLimit0-40000Additional number of emergency calls (expressed as a numeric value) allowed if call limit and emergency over-subscription quota are exhausted. (default = 0)
hpcOversubscription0-100This parameter specifies the amount of resource over-subscription (as a percentage) allowed for HPC calls. When the baseline call limit and bandwidth limit are reached, normal calls are not admitted, but additional HPC calls are allowed up to the configured percentage value. (default = 10)
registerBurstMax

SBC

5000

5xx0:
1-1000 or unlimited

SBC 5400:
1-

200,

1500 or unlimited

SBC 7000:
1-

600,

3000 or unlimited

Maximum

Specifies the maximum allowed egress burst (above the allowed sustained rate) for

egress

initial SIP registrations.

(

The default

= 'unlimited')

value is unlimited. 

Available_since
TypeModified For
Release9.2.1

registerRateMax

SBC 5xx0:
1-1000 or unlimited

SBC 5400

registerRateMax

SBC 5000:
1-100, 1500 or unlimited.

SBC 7000:
1-300, 3000 or unlimited

Maximum Specifies the maximum allowed sustained egress rate of (registrations per second) for initial SIP registrations allowed on this zone. (The default = 'unlimited')

Note
Available_since
TypeModified For
Release9.2.1

Note: You

You

can set both “registerBurstMax” and “registerRateMax” as unlimited; however, if you assign a value to one parameter, the other must also be assigned a value.

Ingress

Command Syntax

Code Block
languagenone
% set addressContext <addressContext_name> zone <zone_name> cac ingress 
	callBurstMax <1-900, or unlimited> (SBC 7000 range is 1-2700)
	callLimit <0-2147483647, or unlimited>
	callRateMax <1-450, or unlimited> (SBC 7000 range is 1-1350)
	emergencyOversubscription <0-1000>
	extendedEmergencyIpLimit <0-40000>
	hpcOversubscription <0-100>
	packetRateMax <1-65535, or unlimited>
	registerBurstMax <1-200,3000 or unlimited> (1-1000 or unlimited for SBC 7000 range is 1-600)
	 5xx0; 1-1500 or unlimited for SBC 5400; 1-3000 or unlimited for SBC 7000)
    registerRateMax <1-100,3000 or unlimited> (1-1000 or unlimited for SBC 7000 range is 1-300)
 5xx0; 1-1500 or unlimited for SBC 5400; 1-3000 or unlimited for SBC 7000)

Command Parameters


Anchor
Ingress Parameters

Caption0Table1

Ingress Parameters

3

Ingress Parameters

You

Note: You can set both callRateMax and callBurstMax as "unlimited"; however, if you assign a value to one parameter, the other must also be assigned a value.

value is unlimited. 

ParameterLength/RangeDescription
callBurstMax

SBC 5000:
1-900, or unlimited.

SBC 7000:
1-2700, or unlimited

Maximum allowed burst (above the allowed sustained rate) for ingress calls, in calls/second. (default = 'unlimited')
callRateMax

SBC 5000:
1-450, or unlimited.

SBC 7000:
1-1350, or unlimited

Maximum sustained ingress call rate allowed in calls/second. (default is 'unlimited')

Note
emergencyOversubscription 0-1000Over-subscription of resources (as a percentage) allowed for emergency calls. (default = 10)
extendedEmergencyIpLimit 0-40000Additional number of emergency calls (expressed as a numeric value) allowed if call limit and emergency over-subscription quota are exhausted. (default = 0)  
hpcOversubscription0-100This parameter specifies the amount of resource over-subscription (as a percentage) allowed for HPC calls. When the baseline call limit and bandwidth limit are reached, normal calls are not admitted, but additional HPC calls are allowed up to the configured percentage value. (default = 10)
packetRateMax1-65535, or unlimitedMaximum sustained packet rate allowed in packets/second. (default = 'unlimited')
registerBurstMax

SBC

5000

5xx0:
1-1000 or unlimited

SBC 5400:
1-

200,

1500 or unlimited

.

SBC 7000:
1-

600,

3000 or unlimited

Maximum

Specifies the maximum allowed ingress burst (above the allowed

sustained rate

sustained rate) for initial SIP registrations.

 (default = 'unlimited')

The default value is unlimited. 

Available_since
TypeModified For
Release9.2.1

registerRateMax

SBC

5000

5xx0:
1-1000 or unlimited

SBC 5400:
1-

100,

1500 or unlimited

.

SBC 7000:
1-

300,

3000 or unlimited

Maximum Specifies the maximum allowed sustained rate of ingress rate (registrations per second) for initial SIP registrations   allowed in registrations/second. (The default = 'unlimited')

Note
Available_since
TypeModified For
Release9.2.1

Note: You can set both “registerBurstMax” and “registerRateMax” as unlimited

You can set both registerBurstMax and registerRateMax as 'unlimited'

; however, if you assign a value to one parameter, the other must also be assigned a value.

Pagebreak