Versions Compared

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

Add_workflow_for_techpubs
AUTH1eyoustra
REV5bscoggins
REV6bscoggins
REV3aross
REV1aross

Panel
In this section:

Table of Contents
maxLevel2

To View Server Admin Objects

A Server Admin configuration object describes the configuration of a server module. A server module can be a standalone server or a server card in a chassis-based system. From this window you can also run commands related to server administration such as managing coredump files or restarting/resetting the server. 

To view the list of Server Admin objects in your system, on the SBC main screen, go to Administration > System Administration > Server Admin. The Server Admin window is displayed.

Caption
0Figure
1Server Admin Window
Info
titleNote

For 1:1 formations on AWS (supported by the Centralized mode), the Server Admin object of the EMA display results for both active and standby volumes. This is because in Centralized mode, the active and standby volumes are always synchronized with each other.  N:1 formations supported by the Distributed mode are not available on the AWS platform.

For more information on Centralized and Distributed modes, refer to System - Admin.

To Edit a Server Admin Object

To edit a Server Admin object, click the adjacent radio button. The Edit Selected Server Admin window appears.

Caption
0Figure
1Edit Selected Server Admin Window

 

Enter Server Admin values using the following table, and click Save.

Caption
0Table
1Server Admin Parameters

Parameter

Description

Name

Specifies the unique name of the server.

Actual CE NameThe instance name assigned by the user (If an instance name is not assigned, this field displays the name.)

Coredump Profile

Select a coredump profile from the drop-down list.

Role

Specifies the server module role. When set to Primary, it designates a server for internal processing. The options are:

  • Primary
  • Secondary
Device Smart Attrib

The smart control attribute value that reports disk life remaining. A value of 0 means that no overriding attribute is available. The SBC could still be using an internal value based on pre-defined settings of known disk types.

If the SBC is unable to retrieve a value (reports "n/a") for Disk Life Remaining when you check hard disk status (refer to System - Hard Disk Status) you may be able to specify the integer ID number of a smart control attribute that reports the percentage lifetime used for the disk. Contact Ribbon Technical Support for assistance in determining whether there is a valid smart control attribute available on your system. 

Modular TypeIf set to 'true', the SBC uses modular DSPs.
Hw TypeTextual description of the SBC hardware type.
Pkt Port Speed

Packet port speed setting:

  • speed1Gbps 
  • speed10Gbps
Hw Subscription Type

For deployments running on a hardware/server environment, this parameter displays the Sonus-defined hardware type.

In SBC SWe deployments, this field contains the SBC SWe subscription type.

  • Virtual – SBC SWe configured for Virtual (non-Cloud) environment.
  • Virtual Cloud – SBC SWe configured for Cloud environment.

Server Admin Commands

Use the Server Admin commands to manage core dump files and perform server actions such as restart and soft reset. 

Caption
0Figure
1Server Admin Commands

Select one of the commands and click Select.  A pop-up window opens where you can specify any required command options and initiate the selected command.

The commands are:

Caption
0Table
1Admin Commands
 

Parameter

Description

Force Core Dump

Use this command to force the termination of a fixed set of application processes with accompanying core dumps for troubleshooting purposes. Select one of the following options in the pop-up window:

  • Full – Full set of processes to dump (see Table 3 below).
  • Partial – Partial set of processes to dump (see Table 4 below).

NOTE: This command causes the SBC application to restart.

Remove Coredump

Use this command to remove a coredump file from the server. In the pop-up window specify the name of the file to remove in Coredump File Name.

Restart

Use this command to restart a server/CE.
Soft ResetUse this command to restart the applications on the system without rebooting the server(s).
Caption
0Table
1Full Application Process List

CamProcess

ChmProcess

CpxAppProc

DiamProcess

DnsProcess

DsProcess

EmaProcess

EnmProcessMain

FmMasterProcess

IkeProcess

ImProcess

IpmProcess

PathchkProcess

PesProcess

PipeProcess

PrsProcess

RtmProcess

SamProcess

ScmProcess_0

ScmProcess_1

ScmProcess_2

ScmProcess_3

ScpaProcess

SmProcess

SsaProcess

SsreqProcess

 

 
Caption
0Table
1Partial Application Process List

DsProcess

PrsProcess

RtmProcess

SamProcess

ScmProcess_0

ScmProcess_1

ScmProcess_2

ScmProcess_3

SmProcess

Pagebreak