Page History

Warning
Sonus-provided SFP modules must be used to guarantee proper operation of the external ports. Failure to follow this recommendation may cause permanent damage to the system.

Tooltip
tip Use ESD protective device

1 Gb SFP Parts

The 

Spacevars
0 model5

supports the following Small Form-factor Pluggable (SFP) transceivers in all Management, Media, and HA ports. SFPs are Customer Replaceable Units (CRUs).

Caption
0 Table 1 1Gb SFP Parts
Transceiver Type

Order Code

Product Code Description Copper SBC-SFPCOPPER-1G GIGE, 1000 BASE-T SMALL FROM PLUGGABLE (SFP) Must use one of the following:   Manufacturer Manufacturer Part Number   AVAGO TECHNOLOGIES ABCU-5710RZ-SN1   AVAGO TECHNOLOGIES ABCU-5740RZ-SN1   BROADCOM ABCU-5740RZ-SN1   FINISAR FCLF8521P2BTL-SS Single-mode fiber SBC-SFPSM-1G

SBC-5400-SFPSM

GIG-E, SINGLE MODE, FIBER OPTIC TRANSCEIVER MODULE, LC, SMALL FORM PLUGGABLE (SFP), 10KM 1310NM, DMI Must use one of the following:   Manufacturer Manufacturer Part Number   AVAGO TECHNOLOGIES AFCT-5715PZ-SN1   BROADCOM AFCT-5715PZ-SN1   FINISAR FTLF1318P2BTL-SS   FINISAR FTLF1318P3BTL-SS Multi-mode fiber

SBC-SFPMM-1G

SBC-5400-SFPMM GIG-E, MULTIMODE, FIBER OPTIC TRANCEIVER MODULE, LC, SMALL FORM PLUGGABLE (SFP), 300M

CopperSBC-SFPCOPPER-1GSBC-5400-SFPCOPPER

Must use one of the following:   Manufacturer Manufacturer Part Number   AVAGO TECHNOLOGIES AFBR-5715PZ-SN1   BROADCOM AFBR-5715PZ-SN1   FINISAR FTLF8519P2BNL-SS   FINISAR FTLF8519P3BNL-SS

GIGE, 1000 BASE-T SMALL FROM PLUGGABLE (SFP)

10 Gb SFP Parts

Optionally, Pkt0 can be used as a single 10 Gb port, with the remaining MEDIA ports empty. The parts for the 10 Gb SFPs are:

Caption
0 Table 1 10Gb SFP Parts
Transceiver Type

Order Code

Product Code Description Single-mode fiber SBC-SFPSM-10G

SBC-5400-SFPSM

10.

3GB

3 GB/S, SINGLE MODE, FIBER OPTIC XCVR, LC, SFP, 10KM 1310NM, DM Must use one of the following:   Manufacturer Manufacturer Part Number   AVAGO TECHNOLOGIES AFCT-709SMZ-SN1   AVAGO TECHNOLOGIES AFCT-739SMZ-SN1   BROADCOM AFCT-739SMZ-SN1   BROADCOM AFCT-709SMZ-SN1   FINISAR FTLX1471D3BCL-SS Multi-mode fiber SBC-SFPMM-10G

SBC-5400-SFPMM

10.

3GB

3 GB/S,

MULTI-MODE

MULTIMODE, FIBER OPTIC XCVR, LC, SFP, 300M 850NM, DMI GIG-E, SINGLE MODE, FIBER OPTIC TRANSCEIVER MODULE Must use one of the following:   Manufacturer Manufacturer Part Number   AVAGO TECHNOLOGIES AFBR-709SMZ-SN1   BROADCOM AFBR-709SMZ-SN1   FINISAR FTLX8574D3BCL-SS   FINISAR FTLX8571D3BCL-SS

To replace SFPs, use the procedures from the section Replacing the SFP.

Caption
0 Figure 1 SFP Ports

Parts and Tools Required

• Electrostatic discharge (ESD) strap
• Replacement SFP transceivers.

Note
To prevent damage from electrostatic discharge, an ESD strap is provided in the accessory kit. Refer to Connecting ESD Wrist Strap to install it.

Anchor
ReplacingSFP ReplacingSFP

Replacing the SFP

Perform the following procedure to replace the SFP:

1. Attach an ESD wrist strap using the ESD grounding point on the rear panel of the chassis (refer to Connecting ESD Wrist Strap for details).

2. Disconnect the fiber optic and/or Cat 5 cables, as appropriate, from media ports (Pkt0/1/2/3) and HA ports (HA 0-1).

3. Disengage the SFP transceiver from

   Spacevars
   0 model5

   . The method used to disengage the SFP transceiver will vary according to the manufacturer. For example, hold the wire latch and move it downwards to the horizontal position and pull it outwards, as shown below.

    

   Caption
   0 Figure 1 Removing SFP

4. Insert the Sonus-approved SFP transceiver into the desired socket and ensure that the latch mechanism engages.

5. Reconnect the fiber optic and/or Cat 5 cables, as appropriate, to media and HA ports.
6. Verify LEDs above the part are flashing indicating link status and data activity.
7. Verify port functionality using the application.

CRU Storage

Tooltip
tip ESD protective device

All 

Spacevars
0 model5

CRUs are shipped in electrostatic discharge bags and should be handled using appropriate ESD precautions.

The storage environment for these CRUs are:

• Humidity must be less than 95% (non-condensing).
• Temperature must be between -40C and +70C.

 

Include Page
ESD_footnote ESD_footnote