Versions Compared

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

Add_workflow_for_techpubs
AUTH2
AUTH1
REV5
REV6
REV3
REV4
REV1REV2

Panel

In this section:

Table of Contents
maxLevel4

The

Spacevars
0series4
includes a configurable Transparency Profile capable of transparently passing SIP headers and SIP message bodies.

This example configuration describes how to create and configure a transparency profile to transparently pass headers and message bodies using the following basic steps:

Table of Contents
stylenone

Though these steps can be performed from either the EMA or from the CLI, the description below is limited to CLI. 

Include Page
Transparency_Profile_Note
Transparency_Profile_Note

 

1. Creating a Transparency Profile

Enter the following commands to create a transparency profile.

Code Block
languagenone
set profiles services transparencyProfile testProfile
commit

2. Configuring Headers and/or Message Bodies in Transparency Profile

Perform the following steps to configure headers and/or message bodies in your transparency profile.

2.1 Configure Headers

  1. Configure Transparency of "all" Headers.

    Code Block
    languagenone
    set profiles services transparencyProfile testProfile sipHeader all
    commit
  2. Configure Transparency of a specific Header with Per-Method Exclusion.

    Code Block
    languagenone
    set profiles services transparencyProfile testProfile sipHeader contact excludedMethods info, notify
    commit
  3. Configure Selective Exclusion of Transparency of Headers.

    Code Block
    languagenone
    set profiles services transparencyProfile testProfile sipHeader contact ignoreTransparency yes 
    commit
Note
iconfalse
titleNote

If a specific header is being configured, ignoreTransparency and excludedMethods are exclusive. If ignoreTransparency is configured, excludedMethods will not display subsequently. If excludedMethods is configured, ignoreTransparency will not display.

The ignoreTransparency configurable applies in the following cases:

  • when combined with a configuration to allow "all" SIP headers
    -or-
  • when one of the transparency flags for SIP header in the IP Signaling Profile is enabled

2.2 Configure Message Bodies

Info
titleInfo

Rules must be configured in the Transparency Profile for the types of content that must be transparently passed through. These rules can be categorized as follows based on the SBC action to take:

  • Rules to allow select types of content through
    • allow any SIP method (of the SIP message) the content may appear in to pass
    • allow any SIP method except certain select methods to pass
  • Rules to disallow select types of content from being transparently passed through

 

  1. Allow a specific type of content through.

    Code Block
    languagenone
    set profiles services transparencyProfile testProfile sipMessageBody application/foo
    commit
    Note
    iconfalse
    titleNote
    This rule does not apply when combined with a rule to allow all types of content. To start out allowing all types of content through, and then excluding specific content, skip to step 2.
  2. Allow all types of content through.

    Code Block
    languagenone
    set profiles services transparencyProfile testProfile sipMessageBody all
    commit
  3. Allow all types of content through in all SIP messages except select SIP methods.

    Code Block
    languagenone
    set profiles services transparencyProfile testProfile sipMessageBody all excludedMethods info,invite 
    commit
  4. Allow a specific message body through in all SIP messages except certain select methods.

    Code Block
    languagenone
    set profiles services transparencyProfile testProfile sipMessageBody application/foo excludedMethods info,invite
    commit
  5. Disallow a message body from being transparently passed through.

    Code Block
    languagenone
    set profiles services transparencyProfile testProfile sipMessageBody application/foo ignoreTransparency yes
    commit
    Note
    iconfalse
    titleNote

    This rule only applies in the following cases:

    1. when combined with a rule to allow all types of content
    2. when one of the transparency flags for message bodies in the IP Signaling Profile is enabled

3. Attaching a Transparency Profile to a Trunk Group

Enter the following commands to attach a transparency profile to a trunk group:

Code Block
languagenone
set addressContext testAC zone testZone sipTrunkGroup testTG services transparencyProfile testProfile
commit

4. Enabling a Transparency Profile

To enable a Transparency Profile, enter the following commands:

Code Block
languagenone
set profiles services transparencyProfile testProfile state enabled
commit

5. Viewing Transparency Profile

To view the currently configured transparency profiles, enter the following 'show' command:

Code Block
languagenone
show profiles services transparencyProfile

Example:

Code Block
languagenone
titleExample
show profiles services transparencyProfile
transparencyProfile test {
    sipHeader all;
    sipMessageBody all;
    sipMessageBody application/foo {
        ignoreTransparency yes;
    }
    sipMessageBody application/new {
        excludedMethods invite,info;
    }
}

Appendix A. Detaching a Transparency Profile From a Trunk Group

Enter the following commands to detach a transparency profile from a trunk group:

Code Block
languagenone
delete addressContext testAC zone testZone sipTrunkGroup testTG services transparencyProfile 
commit

Appendix B. Removing a Transparency Profile

The state of the transparency profile must be disabled before any modification or deletion of the transparency profile can be made. See example below:

Code Block
languagenone
set profiles services transparencyProfile testProfile state disabled
commit

delete profiles services transparencyProfile testProfile
commit

Pagebreak