This section provides information on the Sonus
hardware platform specifications.
...
...
In this section:
...
Chassis
Sonus
is a 2U rack-mounted chassis. The chassis can be front or center mounted in a standard 19 or 23 inch wide rack. At a high level, a fully populated
system is comprised of the following key components.
...
| Caption |
|---|
| 0 | Figure |
|---|
| 1 | SBC 5400 Chassis Front View |
|---|
|
 Image Removed |
Image Added
Rear View
| Caption |
|---|
| 0 | Figure |
|---|
| 1 | SBC 5400 Chassis Rear View |
|---|
| Image Removed
|
Image Added
| Caption |
|---|
| 0 | Table |
|---|
| 1 | SBC 5400 Hardware Specifications |
|---|
| 3 | SBC 5400 Hardware Specifications |
|---|
|
| Front Panel | Rear Panel | Expansion (Modular) | Storage | Memory | Power Option |
|---|
- Status Indicators Front Panel LEDs
- Single USB V2.0 interface
| - 4x100 Mb Management Ports with RJ45 connector
- Media Ports (1x10Gb or 4x1Gb) with SFPs
- Two 1 Gb speed High Availability Ports with SFPs
- 1x100 Mb Single Field Service port with RJ45 connector
- Locator LED
- Alarm port with HD15 connector
- Single serial craft DB9 port
| Four DSP25 or one DSP20 modules | Minimum 480 GB SSD | 32 GB RAM | AC or DC |
|
...
The front panel includes status indicator LEDs and a single USB 2.0 port.
The SBC 5400 Front Bezel bezel LEDs shows the front panel LEDs with and without Bezel without bezel mounted on the front panel of
.
...
| Caption |
|---|
| 0 | Table |
|---|
| 1 | Front panel LEDs Description |
|---|
| 3 | Front panel LEDs Description |
|---|
|
|
Illustration | LED | Color | Description |
|---|
1 | Front Power | Amber/Green | Power status indicator of all voltages generated on the module: - Green = All Power on
- Off = BMC Power on or chassis power is off
|
| 2 | Front Status | Amber/Green | Module Status indicator |
| 3 | Front Active | Amber/Green | Module Redundancy State Indicator: |
| 4 | Front Alarm | Amber/Red | Module Critical/Major Failure Indicator: |
| 5 | Front Locator | White | Module identifier indicator. On or blinking, depending on the "ipmitool chassis identify" command. |
| 6 | FanCtl LED* | Green | Fan module indicator: - Green = Fan module is working
- Off = Fan module is not working
|
| Note |
|---|
|
* This LED is visible only when the Bezel bezel is removed. |
Rear Panel
The rear panel layout and LEDs are as depicted in the Rear Panel LEDs for SBC 5400 figure:
...
| Caption |
|---|
| 0 | Figure |
|---|
| 1 | Rear Panel LEDs for SBC 5400 |
|---|
|
Image Removed |
Image Added
The Rear Panel Description table lists the Ethernet port LEDs. Each of the Management ports, Media ports, HA ports, and FSP port support the following LEDs.
| Caption |
|---|
| 0 | Table |
|---|
| 1 | Rear Panel Description |
|---|
| 3 | Rear Panel Description |
|---|
|
Component | Cable Requirement | Description |
|---|
Alarm Port | Customer supplied cable | Alarm contact via a single shielded male HD15 connector. A single alarm port is present in in SBC 5400 platform.
This software release does not support the Alarm Port. | Management Ports | CAT5e cable | Four copper Ethernet Ports which process Management traffic and perform protocol termination. | Locator | | Module identifier indicator | Media Ports | Single mode or Multi mode fiber/copper CAT5e cable | Four copper SFP or fiber SFP ports for media and signaling traffic. | High Availability Ports | Single mode or Multi mode fiber/copper CAT5e cable (NON-CROSSOVER TYPE ONLY) | Two copper SFP or fiber SFP ports for redundancy synchronization traffic. The platform supports box level redundancy via communication paths provided by the external HA Ethernet ports. | Serial Port | Male DB9 connector | An RS-232 port used by BMC. | Field Service Port | Copper CAT5e cable | A single Field Service Port. | Power Input | | Power Supply. The following are the descriptions of the power supply LED functions: - Off: No power input to the supply.
- Amber: Power supply fault.
- Blinking Amber: Main system power output fault.
- Blinking Green: Standby power to BMC is ON but main system power is not enabled.
- Solid Green: Both standby power to BMC and main system power are ON and OK.
|
|
...
- Alarm contacts are provided on the outside of the chassis through a single shielded male HD15 connector.
- A standard USB connector on the front of the chassis.
- Front and rear jacks for standard ESD straps.
- Cable management.