Page History

Warning
Sonus-provided SFP modules must be used to guarantee proper operation of the external ports. Failure to follow this recommendation may cause permanent damage to the system.

Tooltip
tip Use ESD protective device

1 Gb SFP Parts

The 

Spacevars
0 model5

supports the following Small Form-factor Pluggable (SFP) transceivers in all Management, Media, and HA ports. SFPs are Customer Replaceable Units (CRUs).

Div
class pdf8pttext
Caption 0 Table 1 1Gb SFP Parts 3 1Gb SFP Parts Transceiver Type Product Code

Description

SFP Type

CopperSBC-SFPCOPPER-1GGIGE, 1000 BASE-T SMALL FROM PLUGGABLE (SFP)Must use one of the following: ManufacturerManufacturer Part Number AVAGO TECHNOLOGIESABCU-5710RZ-SN1 AVAGO TECHNOLOGIESABCU-5740RZ-SN1 BROADCOMABCU-5740RZ-SN1 FINISARFCLF8521P2BTL-SSSingle-mode fiberSBC-SFPSM-1G

Manufacturers  Part Number Wavelength  (nm) Tx Power (dBM) Rx Power (dBM) Description Multi-mode fiber SBC‐5XXXSFPMM   1G Ethernet MM AVAGO TECHNOLOGIES AFBR‐5715PZSN1, BROADCOM AFBR‐5715PZ‐SN1, FINISAR FTLF8519P2BNL‐SS, FINISAR  FTLF8519P3BNL‐SS 850 -9.5 (Min) -3 (Max) -17 (Min) 0 (Max) GIG-E, MULTIMODE, FIBER OPTIC TRANCEIVER

GIG-E, SINGLE MODE, FIBER OPTIC TRANSCEIVER

MODULE, LC, SMALL FORM PLUGGABLE (SFP),

10KM 1310NM, DMIMust use one of the following: ManufacturerManufacturer Part Number AVAGO TECHNOLOGIESAFCT-5715PZ-SN1 BROADCOMAFCT-5715PZ-SN1 FINISARFTLF1318P2BTL-SS FINISARFTLF1318P3BTL-SSMulti-mode fiberSBC-5400-SFPMMGIG-E, MULTIMODE, FIBER OPTIC TRANCEIVER

300M Single-mode fiber SBC‐5XXXSFPSM   1G Ethernet  SM AVAGO TECHNOLOGIES AFCT‐5715PZSN1, BROADCOM AFCT‐5715PZSN1, FINISAR FTLF1318P2BTL‐SS, FINISAR FTLF1318P3BTL‐SS 1310 -9.5 (Min) -3 (Max) -19 (Min) -3 (Max) GIG-E, SINGLE MODE, FIBER OPTIC TRANSCEIVER MODULE, LC, SMALL FORM PLUGGABLE (SFP),

300M

10KM 1310NM, DMI Copper  SBC-5XXX-SFPCOPPER 1G Ethernet Copper  AVAGO TECHNOLOGIES ABCU-5740RZ-SN1, BROADCOM ABCU-5740RZ-SN1, FINISAR FCLF8521P2BTL-SS NA NA NA NA NA GIGE, 1000 BASE-T SMALL FROM PLUGGABLE (SFP)

Note
These numbers are taken from Vendor Datasheets as well as IEEE 802.3ae for the 1G parts.

Must use one of the following: ManufacturerManufacturer Part Number AVAGO TECHNOLOGIESAFBR-5715PZ-SN1 BROADCOMAFBR-5715PZ-SN1 FINISARFTLF8519P2BNL-SS FINISARFTLF8519P3BNL-SS

10 Gb SFP Parts

Optionally, Pkt0 can be used as a single 10 Gb port, with the remaining MEDIA ports empty. The parts for the 10 Gb SFPs are:

Div
class pdf8pttext
Caption 0 Table 1 10Gb SFP Parts 3 10Gb SFP Parts Transceiver Type Product Code

DescriptionSingle-mode fiberSBC-SFPSM-10G10.3 GB/S, SINGLE MODE, FIBER OPTIC XCVR, LC, SFP, 10KM 1310NM, DMMust use one of the following: ManufacturerManufacturer Part Number AVAGO TECHNOLOGIESAFCT-709SMZ-SN1 AVAGO TECHNOLOGIESAFCT-739SMZ-SN1 BROADCOMAFCT-739SMZ-SN1 BROADCOMAFCT-709SMZ-SN1 FINISARFTLX1471D3BCL-SSMulti-mode fiberSBC-SFPMM-10G

SFP Type Manufacturers  Part Number Wavelength  (nm) Tx Power (dBM) Rx Power (dBM) Description Multi-mode fiber SBC‐SFPMM‐10G 10G Ethernet MM AVAGO TECHNOLOGIES AFBR‐709SMZSN1, BROADCOM AFBR‐709SMZ‐SN1,  FINISAR FTLX8571D3BCL‐SS, FINISARFTLX8574D3BCL‐SS 850 -7.9 (Min) -1 (Max) -11.1 (Min) 0.5 (Max) 10.3 GB/S, MULTIMODE, FIBER OPTIC XCVR, LC, SFP, 300M 850NM, DMI GIG-E, SINGLE MODE, FIBER OPTIC TRANSCEIVER MODULE

Must use one of the following:

Single-mode fiber SBC‐SFPSM‐10G

ManufacturerManufacturer Part Number AVAGO TECHNOLOGIESAFBR-709SMZ-SN1 BROADCOMAFBR-709SMZ-SN1 FINISARFTLX8574D3BCL-SS

10G Ethernet  SM AVAGO TECHNOLOGIES AFCT‐709SMZSN1, AVAGO TECHNOLOGIES AFCT739SMZ‐SN1, BROADCOM AFCT‐709SMZSN1, BROADCOM AFCT‐739SMZ‐SN1,  FINISAR FTLX1471D3BCL‐SS 1310 -8.2 (Min) 0.5 (Max) -12.6 (Min) 0.5 (Max) 10.3 GB/S, SINGLE MODE, FIBER OPTIC XCVR, LC, SFP, 10KM 1310NM, DM

Note
These numbers are taken from Vendor Datasheets as well as IEEE 802.3ae for the 10G parts.

 FINISARFTLX8571D3BCL-SS

To replace SFPs, use the procedures from the section Replacing the SFP.

Caption
0 Figure 1 SFP Ports

Parts and Tools Required

• Electrostatic discharge (ESD) strap
• Replacement SFP transceivers.

Note
To prevent damage from electrostatic discharge, an ESD strap is provided in the accessory kit. Refer to Connecting ESD Wrist Strap to install it.

Anchor
ReplacingSFP ReplacingSFP

Replacing the SFP

Perform the following procedure to replace the SFP:

1. Attach an ESD wrist strap using the ESD grounding point on the rear panel of the chassis (refer to Connecting ESD Wrist Strap for details).

2. Disconnect the fiber optic and/or Cat 5 cables, as appropriate, from media ports (Pkt0/1/2/3) and HA ports (HA 0-1).

3. Disengage the SFP transceiver from

   Spacevars
   0 model5

   . The method used to disengage the SFP transceiver will vary according to the manufacturer. For example, hold the wire latch and move it downwards to the horizontal position and pull it outwards, as shown below.

    

   Caption
   0 Figure 1 Removing SFP

4. Insert the Sonus-approved SFP transceiver into the desired socket and ensure that the latch mechanism engages.

5. Reconnect the fiber optic and/or Cat 5 cables, as appropriate, to media and HA ports.
6. Verify LEDs above the part are flashing indicating link status and data activity.
7. Verify port functionality using the application.

CRU Storage

Tooltip
tip ESD protective device

All 

Spacevars
0 model5

CRUs are shipped in electrostatic discharge bags and should be handled using appropriate ESD precautions.

The storage environment for these CRUs are:

• Humidity must be less than 95% (non-condensing).
• Temperature must be between -40C and +70C.

Include Page
ESD_footnote ESD_footnote