Versions Compared

Old Version 7

changes.mady.by.user Ribbon Communications

Saved on

compared with

New Version 8

changes.mady.by.user Ribbon Communications

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

Add_workflow_for_techpubs
AUTH1sbsarkar
REV5bscoggins
REV6bscoggins
REV3areddy
REV1
REV2agogate

Panel

In this section:

Table of Contents
maxLevel3

Info
iconfalse

Related articles:

Children Display

 

The

Spacevars
0series4
 includes a signaling profile, NNI Profile, in support of the Inter-IMS Network to Network Interface (II-NNI) and interworking of charging parameters for SIP to/from SIP-I/T/GWGW/ISUP calls. The NNI Profile is attached to a ingress SIP trunk group. To learn more about how the
Spacevars
0product
 performs SIP to SIP-I and SIP-I to SIP interworking based on the NNI Profile, refer to PCV Interworking Enhancement.

Info
titleInfo

The

Spacevars
0product
supports up to 32 NNI profiles. 

To View NNIProfile

On the SBC main screen, navigate to All > Profiles > Signaling > NNIProfile.

The NNIProfile window is displayed.

Caption
0Figure
1NNIProfile

To Edit NNIProfile

To edit any of the NNIProfile in the list, click the radio button next to the specific NNIProfile name.

Caption
0Figure
1Select the NNIProfile

 

The Edit Selected NNIProfile window is displayed.

Caption
0Figure
1The NNIProfile Edit Window

 

Make the required changes and click Save at the right hand bottom of the panel to save the changes made.

To Create NNIProfile

To create a new NNIProfile, click New NNIProfile tab on the NNIProfile List panel.

Caption
0Figure
1The NNIProfile Fields

 

The Create New NNIProfile window is displayed.

Caption
0Figure
1Create New NNIProfile

 

The NNI Profile parameters (as displayed in the Copy and Edit tools) are described below:

Caption
0Table
1NNI Profile Parameter Descriptions
3NNI Profile Parameter Descriptions
6.2.1
Parameter DescriptionLength/RangeParameter Description
Name1-23 characters

The name of the NNIProfile used to control

Spacevars
0product
interworking of charging parameters for SIP to/from SIP-I/T, GW-GW and ISUP calls. The NNI Profile is attached to a SIP trunk group.

Charge Area Information(ASCII 0-9)A 5-digit value representing the charge area Information that applies to calls establishing the INVITE.
 Additional Party Category First

N/A

Use this parameter to select one of the following values to specify the first Additional Party Category type. The configured value will be included inside the policy request message sent to the PSX and sent in the ISUP IAM message body of SIP-I/T or over GW-GW message.

  • Fixed_1-1
  • Fixed_1-2
  • Mobile_1-1
  • Mobile_1-2
  • Mobile_1-3
  • Mobile_1-4
  • Mobile_1-5
  • Mobile_2-1
  • Mobile_2-2
  • Mobile_2-3
  • Mobile_2-4
  • Mobile_2-5
  • Mobile_2-6
  • Mobile_2-7
  • Mobile_2-8
  • Mobile_2-9
 Additional Party Category Second

N/A

Use this parameter to select one of the above values to specify the second Additional Party Category type. The configured value will be included inside the policy request message sent to the PSX and sent in the ISUP IAM message body of SIP-I/T or over GW-GW message.
Calling Party Category InterworkingN/A

The flag Calling Party Category Interworking has two possible values:

  • Disabled (default)
  • Enabled

 To start Calling Party Category Interworking, set this flag to enabled. When set to enabled, the

Spacevars
0product
populates the parameter Calling Party Category (CPC) with the value 11, on receiving the Resource Priority Header (RPH) in the initial INVITE. Here, the value 11 denotes "Calling Subscriber with priority". When RPH is absent in the initial INVITE, SBC populates the parameter CPC from the PAI Header.

History Info InterworkingN/A

The flag History Info Interworking has two possible values:

  • Disabled (default)
  • Enabled

 To start History Info Interworking, set this flag to enabled. When set to enabled, for the SIP-SIP-I call leg, the

Spacevars
0product
maps History Info Header to ISUP Parameters (Original Called Number, Redirection Number, and Redirection Information). For the SIP-I-SIP call leg, the SBC maps the ISUP parameters in the MIME body to the corresponding History Info Header.

To summarize, when History Info Interworking is enabled, the SBC supports the following mappings:

  • History-Info to ISUP parameters (Redirecting Number, Original Called Number, and Redirection Information) for redirection, and the other way for the SIP-I-SIP call leg.
  • History-Info to ISUP parameters (Called IN Number and Original Called IN Number) for number translation, and the other way for the SIP-I-SIP call leg.
Enable PVCTTCParamsN/A

When disabled, the SBC deactivates the NNI PCV to trigger. The options are:

  • Disabled (default)
  • Enabled
Set Hi Presentation Restricted
N/A

Available_since
TypeAvailable Since
Release6.2.1
The flag Set Hi Presentation Restricted has two possible values:

  • Disabled (default) – When set to disabled, the SBC sends send the Presentation as per privacy information it received.
  • Enabled – When set to enabled, the SBC sends the APRH (Address Presentation Restricted Indicator) as "Presentation Restricted" irrespective of privacy information in the History-Info (HI) header.

If privacy=history, Presentation should be Restricted 

 

If privacy=none or not present, Presentation should be allowed

Add User Equal Phonefor Div Hi Interworking
N/A
Available_since
TypeAvailable Since
Release

To start Add User Equal Phonefor Div Hi Interworking, set this flag to enabled.

  • Disabled (default) – When set to disabled, the SBC will not add user=phone and mp parameter to history-info in Diversion-History-Info interworking.
  • Enabled – When set to enabled, the SBC sends user=phone and the mp parameter to history-info header, but only for Diversion-History-Info interworking.

To Copy NNIProfile

To copy any of the created NNIProfile and to make any minor changes, click the radio button next to the specific NNIProfile.

Caption
0Figure
1Select the NNIProfile to be Copied

 

Click Copy NNIProfile tab on the NNIProfile List panel.

Caption
0Figure
1The NNIProfile Fields

 

The Copy Selected NNIProfile window is displayed along with the field details which can be edited.

Caption
0Figure
1Copy Selected NNIProfile Window

Caption
0Table
1NNI Profile Parameter Descriptions
3NNI Profile Parameter Descriptions
Parameter DescriptionLength/RangeParameter Description
Name1-23 characters

The name of the NNIProfile used to control

Spacevars
0product
interworking of charging parameters for SIP to/from SIP-I/T, GW-GW and ISUP calls. The NNI Profile is attached to a SIP trunk group.

Charge Area Information(ASCII 0-9)A 5-digit value representing the charge area Information that applies to calls establishing the INVITE.
Additional Party Category First

N/A

Use this parameter to select one of the following values to specify the first Additional Party Category type. The configured value will be included inside the policy request message sent to the PSX and sent in the ISUP IAM message body of SIP-I/T or over GW-GW message.

  • Fixed_1-1
  • Fixed_1-2
  • Mobile_1-1
  • Mobile_1-2
  • Mobile_1-3
  • Mobile_1-4
  • Mobile_1-5
  • Mobile_2-1
  • Mobile_2-2
  • Mobile_2-3
  • Mobile_2-4
  • Mobile_2-5
  • Mobile_2-6
  • Mobile_2-7
  • Mobile_2-8
  • Mobile_2-9
Additional Party Category Second

N/A

Use this parameter to select one of the above values to specify the second Additional Party Category type. The configured value will be included inside the policy request message sent to the PSX and sent in the ISUP IAM message body of SIP-I/T or over GW-GW message.
Calling Party Category InterworkingN/A

The flag Calling Party Category Interworking has two possible values:

  • Disabled (default)
  • Enabled

 To start Calling Party Category Interworking, set this flag to enabled. When set to enabled, the

Spacevars
0product
populates the parameter Calling Party Category (CPC) with the value 11, on receiving the Resource Priority Header (RPH) in the initial INVITE. Here, the value 11 denotes "Calling Subscriber with priority". When RPH is absent in the initial INVITE, SBC populates the parameter CPC from the PAI Header.

History Info InterworkingN/A

The flag History Info Interworking has two possible values:

  • Disabled (default)
  • Enabled

 To start History Info Interworking, set this flag to enabled. When set to enabled, for the SIP-SIP-I call leg, the

Spacevars
0product
maps History Info Header to ISUP Parameters (Original Called Number, Redirection Number, and Redirection Information). For the SIP-I-SIP call leg, the SBC maps the ISUP parameters in the MIME body to the corresponding History Info Header.

To summarize, when History Info Interworking is enabled, the SBC supports the following mappings:

  • History-Info to ISUP parameters (Redirecting Number, Original Called Number, and Redirection Information) for redirection, and the other way for the SIP-I-SIP call leg.
  • History-Info to ISUP parameters (Called IN Number and Original Called IN Number) for number translation, and the other way for the SIP-I-SIP call leg.
Enable PVCTTCParamsN/A

When disabled, the SBC deactivates the NNI PCV to trigger. The options are:

  • Disabled (default)
  • Enabled
   
   
Carrier Information Transfer - Carrier Category And InfoN/A

Use this object to define the carrier poi-category and carrier ID code.

  • Carrier Category – The carrier category type.
    • Olec – The SBC inserts the "olec" in the SIP requests in SIP to SIP-I interworking scenarios.
    • Tlec – The SBC inserts the "tlec" (terminating carrier info) in the SIP responses in SIP to SIP-I interworking scenarios.
  • Carrier Info - Carrier ID Code – A 4-digit carrier identification code associated with the charge area. Only ASCII characters from 0 to 9 are valid.

NOTE: The following Carrier Category values are not supported in this release:

    • Ciec
    • Iec
    • Scpc
Forward Call IndicatorN/A

Use this object to configure forward call indicator settings.

  • National Call Indicator – Choose a National Call Indicator type:
    • Int – International call
    • Nat – National call
  • Originating Isdn Indicator – Choose an Originating ISDN Access Indicator type:
    • Non_Isdn
    • Isdn
 

Make the required changes to the required fields and click Save to save the changes. The copied NNIProfile is displayed at the bottom of the original NNIProfile in the NNIProfile List panel.

To Delete NNIProfile

To delete any of the created NNIProfile, click the radio button next to the specific NNIProfile which you want to delete.

Caption
0Figure
1Select the NNIProfile to be Deleted

 

Click Delete at the end of the highlighted row. A delete confirmation message appears seeking your decision.

Caption
0Figure
1The NNIProfile Delete Confirmation

 

 

Additional Sections

Div
styleleft-padding:10%
idindent

Children Display
styleh6

Pagebreak