...
On SBC main screen, navigate to Address Context Configuration > Intercept > Call Data Channel.
...
| Caption |
|---|
| 0 | Figure |
|---|
| 1 | Intercept - Call Data Channel Main Field |
|---|
|
 Image Modified
|
The Call Data Channel window is displayed.
| Caption |
|---|
| 0 | Figure |
|---|
| 1 | Intercept - Call Data Channel |
|---|
|
Image Modified |
To Edit Call Data Channel
...
| Caption |
|---|
| 0 | Figure |
|---|
| 1 | Intercept - Call Data Channel Highlighted |
|---|
|
Image Modified |
The Edit Selected Call Data Channel window is displayed below.
| Caption |
|---|
| 0 | Figure |
|---|
| 1 | Intercept - Call Data Channel Edit Window |
|---|
|
Image Modified |
Make the required changes and click Save at the right hand bottom of the panel to save the changes made.
...
| Caption |
|---|
| 0 | Figure |
|---|
| 1 | Intercept - Call Data Channel Fields |
|---|
|
Image Modified |
The Create New Call Data Channel window is displayed.
| Caption |
|---|
| 0 | Figure |
|---|
| 1 | Intercept - Call Data Channel Create Window |
|---|
|
Image Modified |
The following fields are displayed:
| Caption |
|---|
| 0 | Table |
|---|
| 1 | Call Data Channel Parameters |
|---|
|
Parameter | Description |
|---|
Name
| Specifies the name of the IP interface group used to stream to the LI Server. | Pri State
| Specifies if the communication to the primary LI Server is enabled or not. Options are: | Sec State
| Specifies if the communication to secondary LI Server is enabled or not. Options are: | Pri Mode
| Specifies the mode of the primary server. Options are: active standbyout of service
| Sec Mode
| Specifies the mode of the secondary server. Options are: active standby out of service
| Pri IP Address
| Specifies the primary LI Server's IP address where Call Data Channel messages are sent. | Sec IP Address
| Specifies the secondary LI Server's IP address where Call Data Channel messages are sent. | Pri Port
| Specifies the primary LI Server's UDP port where Call Data Channel messages are sent. | Ka Timer
| Specifies the Keep Alive Timer in seconds. | Retries
| Specifies the number of retries before LI Call Data Channel is considered failed. | IP Interface Group Name
| Specifies the name of the IP interface group used to stream to the LI Server. | Li Pol Dip For Regd Ood Msg | Specifies that the policy dip to PSX for the Out-Of-Dialog messages of the registered user is enabled or not. Options are: | Dsr TCP Port | The TCP port of the LI server where DSR messages are sent. This value is set when Media Type Intercepted is set to Multimedia. | Media Type Intercepted | Specifies the media type interception. Options are: DefaultMultimedia - When set to multimedia, SBC supports interception of media (audio, fax, clearmode) streams in Encapsulation mode. It also supports the Direct Signaling Report (DSR) messages. DSR messages are signaling messages generated by SBC, when a call is intercepted. The DSR message contains the extra information in the header along with the actual signaling message PDUs.
|
|
To Copy Call Data Channel
...
| Caption |
|---|
| 0 | Figure |
|---|
| 1 | Copy operation information for Call Data Channel |
|---|
|
Image Modified |
To Delete Call Data Channel
...
| Caption |
|---|
| 0 | Figure |
|---|
| 1 | Intercept - Call Data Channel Highlighted |
|---|
|
Image Modified |
Click Delete at the end of the highlighted row. A delete confirmation message appears seeking your decision.
| Caption |
|---|
| 0 | Figure |
|---|
| 1 | Intercept - Call Data Channel Delete Confirmation |
|---|
|
Image Modified |
Click OK to remove the specific Call Data Channel from the list.