Versions Compared

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Comment: Migrated to Confluence 5.3

...

Caption
0Figure
1Profile Management - Media Profiles - Condition In Addition To No Common Codec

Image Modified

The following fields are displayed:

Caption
0Table
1Conditions in Addition to No Common Codec
ParameterDescription
Apply Fax Tone TreatmentThis flag is same as applyFaxToneTreatment flag in PSP in external PSX configuration. It is being used to apply FaxToneTreatmentconfiguration while transitioning to fax call. The options are: 
  • Enable
  • Disable (default)
Different DTMF Relay When selected, the
Spacevars
0series
performs transcoding when the ingress and egress call legs use different DTMF relay methods. When cleared,
Spacevars
0series
transcoding is not determined by different DTMF relay methods. The options are: 
  • Enable
  • Disable (default)
Different Packet Size When selected, the
Spacevars
0series
performs transcoding when the ingress and egress call legs use different packet sizes. When cleared,
Spacevars
0series
transcoding is not determined by different packet size. The options are: 
  • Enable
  • Disable (default)
Different Silence Suppression When selected, the
Spacevars
0series
performs transcoding when the ingress and egress call legs use different silence suppression methods. When cleared,
Spacevars
0series
transcoding is not determined by different silence suppression methods. The options are: 
  • Enable
  • Disable (default)
Honor Offer Preference

When selected, and this packet service profile is applied to either ingress or egress call leg, the Condition In Addition To No Common Codec offer list of the remote peer is given preference. This option available only when Transcode=Conditional. The options are:  

  • Enable
  • Disable (default)
Honor Answer Preference

Currently, SBC controls honoring the codec preference of the offerer using Honor Offer Preference (HOP) flag only in PSP Object using the PSX provided Honor Remote Preference (HRP) flag is enabled. The answerer codec preference is now controlled as part of this feature using the Honor Answer Preference (HAP) flag available in PSP Object using the PSX. SBC supports the following behavior based on the PSX flag selection of these flags. Note that these flags are leg independent, that is, it can be enabled on any associated PSP to take effect.

When HOP flag is enabled and HAP flag is disabled:

This is the current behavior of SBC. It selects a codec order of precedence in the offered SDP, irrespective of whether it is a pass-thru or a transcoded codec (provided transcoding is defined for that codec). SBC as part of media lockdown may send a re-INVITE to egress peer. Note that the preference on the answerer side is given to a pass-through codec.

When both HOP and HAP flags are enabled:

SBC gives preference to HAP over HOP in case of conflict. The Honor Remote Preference (HRP) flag on the answerer leg decides the preference order. Based on that preference list, SBC selects a codec with highest preference from answer SDP that can be used even if it requires transcoding. Note that this may cause the selection of a codec on the other side leg not to be honored. This happens in case of a passthrough call.

When HAP flag is enabled and HOP is disabled:

SBC gives preference to answerer codec order that is created based on HRP flag. The most preferred codec is chosen as received in the answer SDP, irrespective of whether it is a pass-thru or a transcoded codec (provided transcoding is defined for that codec).

The options are: 

  • Enable
  • Disable (default)

When you select Only or Determined By PSP For Other Leg in the Transcode section,

Spacevars
0series
disables the check boxes in this section.

Different2833Payload TypeWhen selected, SBC allows to transcode media when RFC2833 payload type received from ingress is different from the preferred DTMF payload type configured in egress PSP. The options are: 
  • Enable
  • Disable (default)

Make the required changes and click Save at the right hand bottom of the panel to save the changes made.

...