Page History
| Add_workflow_for_techpubs | |||||||||
|---|---|---|---|---|---|---|---|---|---|
|
| Noprint | |||||||||
|---|---|---|---|---|---|---|---|---|---|
|
| Panel | ||||
|---|---|---|---|---|
In this section:
|
| Warning |
|---|
Sonus-provided SFP modules must be used to guarantee proper operation of the external ports. Failure to follow this recommendation may cause permanent damage to the system. |
| Tooltip | ||
|---|---|---|
| ||
|
...
1 Gb SFP Parts
The
| Spacevars | ||
|---|---|---|
|
| Transceiver Type | Order Code | Product Code | Description |
|---|---|---|---|
| Single-mode fiber | SBC-SFPSM-1G | SBC-5400-SFPSM | GIG-E, SINGLE MODE, FIBER OPTIC TRANSCEIVER MODULE, LC, SMALL FORM PLUGGABLE (SFP), 10KM 1310NM, DMI |
| Multi-mode fiber | SBC-SFPMM-1G | SBC-5400-SFPMM | GIG-E, MULTIMODE, FIBER OPTIC TRANCEIVER MODULE, LC, SMALL FORM PLUGGABLE (SFP), 300M |
| Copper | SBC-SFPCOPPER-1G | SBC-5400-SFPCOPPER | GIGE, 1000 BASE-T SMALL FROM PLUGGABLE (SFP) |
...
10 Gb SFP Parts
Optionally, Pkt0 can be used as a single
...
10 Gb port, with the remaining MEDIA ports empty. The parts for the
...
10 Gb SFPs are:
| Transceiver Type | Order Code | Product Code | Description |
|---|---|---|---|
| Single-mode fiber | SBC-SFPSM-10G | SBC-5400-SFPSM | 10.3GB/S, SINGLE MODE, FIBER OPTIC XCVR, LC, SFP, 10KM 1310NM, DM |
| Multi-mode fiber | SBC-SFPMM-10G | SBC-5400-SFPMM | 10.3GB/S, MULTI-MODE, FIBER OPTIC XCVR, LC, SFP, 300M 850NM, DMI |
To replace SFPs, use the procedures from the section Replacing the SFP.
| Caption | ||||
|---|---|---|---|---|
| ||||
|
Parts and Tools Required
- Electrostatic discharge (ESD) strap
- Replacement SFP transceivers.
| Note |
|---|
To prevent damage from electrostatic discharge, an ESD strap is provided in the accessory kit. |
...
Refer to Connecting ESD Wrist Strap to install it. |
| Anchor | ||||
|---|---|---|---|---|
|
Perform the following procedure to replace the SFP:
- Attach an ESD wrist strap using the ESD grounding point on the rear panel of the chassis (
...
- refer to Connecting ESD Wrist Strap for details).
Disconnect the fiber optic and/or Cat 5 cables, as appropriate, from media ports (Pkt0/1/2/3) and HA ports (HA 0-1).
Disengage the SFP transceiver from
. The method used to disengage the SFP transceiver will vary according to the manufacturer. For example, hold the wire latch and move it downwards to the horizontal position and pull it outwards, as shown below.Spacevars 0 model5 Caption 0 Figure 1 Removing SFP 
Insert the Sonus-approved SFP transceiver into the desired socket and ensure that the latch mechanism engages.
- Reconnect the fiber optic and/or Cat 5 cables, as appropriate, to media and HA ports.
- Verify LEDs above the part are flashing indicating link status and data activity.
- Verify port functionality using the application.
CRU Storage
| Tooltip | ||
|---|---|---|
| ||
|
All
| Spacevars | ||
|---|---|---|
|
The storage environment for these CRUs are:
- Humidity must be less than 95% (non-condensing).
- Temperature must be between -40C and +70C.
| Include Page | ||||
|---|---|---|---|---|
|
Overview
Content Tools