Versions Compared

Old Version 5

changes.mady.by.user Ribbon Communications

Saved on

compared with

New Version 6

changes.mady.by.user Ribbon Communications

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Comment: update the content for the SBX-44930 new ICD

 

Add_workflow_for_techpubs
AUTH1
REV5
REV6
REV3
REV1

...

Include Page
IP_IGs_ServedBySeperateProcessors
IP_IGs_ServedBySeperateProcessors

Command Syntax

For SBC 5xx0/7000/SWe:

Code Block
languagenone
% set addressContext <addressContext_name> zone <zone_name> gwSigPort <#>
ipVaripAddress <IP<IPv4 Var>
ipAddressor <IPIPv6 address>
ipInterfaceGroupName <name>
mode <inService | outOfService>
portNumber <#>
role <primary | secondary>
state <disabled | enabled>

 

// Mandatory parameters:

Code Block
languagenone
ipInterfaceGroupName <name>
portNumberipAddress <Ip Address>
 portNumber <#>

// Non-mandatory parameters:

Code Block
languagenone
mode <outOfService | inService>
role <primary | secondary>
state <disabled | enabled>

For Virtual SBC ,I-SBC and D-SBC

Code Block
languagenone
% set addressContext <addressContext_name> zone <zone_name> gwSigPort <#>
ipInterfaceGroupName <name>
ipVar <IPv4 or IPv6 private IP address - I-SBC/D-SBC only>
mode <inService | outOfService>
portNumber <#>ipAddress <ip address>
mode <outOfService | inService>
role <primary | secondary>
state <disabled | enabled>

// Mandatory parameters:

Code Block
ipInterfaceGroupName <name>

 

// Non-mandatory parameters:

Code Block
ipVar <IPv4 or IPv6 private IP address - I-SBC/D-SBC only>
mode <inService | outOfService>
portNumber <#>
role <primary | secondary>
state <disabled | enabled>
ipVar <IP Var>

Command Parameters

Caption
0Table
1Zone Gateway Signaling Port Parameters
 

Parameter

Length/Range

Description

zone

1-23 characters

The name of the zone. For GW-to-GW calls, zone must be “defaultSigZone”.

You can configure signaling, media, and control for a zone in the address context.

Note
Zone name must be unique across all address contexts

.

gwSigPort

1-2048

Gateway (GW) signaling   ports for this zone. Enter an index number for this port, and select parameters:

  •   ipAddress – IP Address of the Gateway Signal Listen Port, either in IPv4 or IPv6 format.
Note
An IPv4-mapped IPv6 address is not allowed.
  • ipInterfaceGroupName – Name of IP interface group used by this gateway signaling port.
  • ipVar – Metavariable name associated with the gateway signaling port IP address. This is used to configure gateway signaling IP address in SBC SWe Cloud.

    Note: You can view the parameter only for virtual SBC SWe, I-SBC and D-SBC platforms.
     
  • mode – The operational mode for this gateway signaling port.
    • inService (default)
    • outOfService
  • portNumber – TCP Port number of gateway signaling port
      (default = 2569).
  • role – Role of the gateway signal listening port.
    • primary – (default) Create a listening port for Gateway signaling traffic.
    • secondary – An alternate port used for listening only and cannot be used to establish new gateway signal links.
  • state – Administrative state of gateway listening port.  
    • disabled (default)
    • enabled
     
    • ipVar – Metavariable name associated with the gateway signaling port IP address. This is used to

 

CLI Example

To configure gateway signaling

...

on for SBC 5xx0/7000/SWe, execute the following commands

Code Block
set addressContext default zone defaultSigZone gwSigPort 1
Value for 'ipInterfaceGroupName' [LIF1,LIF2]: LIF1
Value for 'ipAddress' (<IP address>): 10.54.23.51
[ok]
set addressContext default zone defaultSigZone gwSigPort 1 ipInterfaceGroupName LIFI ipAddress 10.54.23.51 portNumber 1 role primary state enable

...

 

...

 
To configure MCS Signaling Gateway gateway signaling on an I-SBC and D-SBC, execute the command:following commands
 Code Block
set addressContext default zone defaultSigZone id 1 gwSigPort 1 ipVar IF2.IPV4 portNumber 2569 ipInterfaceGroupName LIG1 mode inService role primary state enabled
commit
set addressContext default zone defaultSigZone gwTrunkGroup GATEWAY_TG media mediaIpInterfaceGroupName LIG1
commit 
set addressContext default zone defaultSigZone gwTrunkGroup GATEWAY_TG state enabled mode inService ingressIpPrefix 10.34.0.0 16
commit 

 Pagebreak