...
This section provides information on the Sonus SBC 5400 Sonus
hardware platform specifications.
Chassis
Sonus SBC 5400 system is contained in Sonus
is a 2U rack-mounted chassis. The chassis can be front or center mounted in a standard 19
-inch wide rack, with optional rack hardware to mount it in a 23-or 23 inch wide rack. At a high level, a fully
populated SBC 5400 populated system is comprised of the following key components.
- Motherboard
- Four DSP2x DSP25 or one DSP20 modules
- Three Fan assemblies
- Solid state driveState Drive (SSD)
- Two power supplies
Front View
...
| Caption |
|---|
| 0 | Table |
|---|
| 1 | SBC 5400 Hardware Specifications |
|---|
| 3 | SBC 5400 Hardware Specifications |
|---|
|
| Front Panel | Rear Panel | Expansion (Modular) | Storage | Memory | Power Option |
|---|
- Status Indicators Front Panel LEDs
- Single USB V2.0 interface
| - 4x100 Mb Management Ports with RJ45 connector
- Media Ports (1x10Gb or 4x1Gb) with SFPs
- Two 1 Gb High Availability Ports with SFPs
- 1x100 Mb Single Field Service port with RJ45 connector
- Locator LED
- Alarm port with HD15 connector
- Single serial craft DB9 port
| Up to four DSP2x cardsFour DSP25 or one DSP20 modules | Minimum 480 GB Solid State Disk
( SSD) | 32 GB RAM | AC or DC |
|
Front Panel
The chassis includes a front panel on which the various input/output ports and LEDs are locatedThe front panel includes status indicator LEDs and a single USB 2.0 port.
The Front Bezel and LEDs of SBC 5400 figure shows the front panel LEDs with and without Bezel mounted on the front panel of SBC 5400of
.
| Anchor |
|---|
| Front Bezel and LEDs of SBC 5400 Series |
|---|
| Front Bezel and LEDs of SBC 5400 Series |
|---|
|
...
The Front panel LEDs Description table lists the front panel LEDs on the SBC 5400. The default state of all LEDs are during a reset
.
| Caption |
|---|
| 0 | Table |
|---|
| 1 | Front panel LEDs Description |
|---|
| 3 | Front panel LEDs Description |
|---|
|
Illustration | LED | Color | Description |
|---|
1 | Front Power | Amber/Green | Power status indicator of all voltages generated on the module: - Green = All Power on
- Off = BMC Power on Off = All Power is Offor chassis power is off
| | 2 | Front Status | Amber/Green | Module Status indicator | | 3 | Front Active | Amber/Green | Module Redundancy State Indicator: | | 4 | Front Alarm | Amber/Red | Module Critical/Major Failure Indicator: | | 5 | Front Locator | White | Module identifier indicator. On or blinking, depending on the "ipmitool chassis identify" command. | | 6 | FanCtl LED | Green | Fan module indicator: - Green = Fans are working
- Off = Module is not working
|
|
Rear Panel
The following figures list the rear panel LEDs on the SBC 5400. The default state of all LEDs is during a reset. The rear panel layout and LEDs are as depicted in the Rear Panel LEDs for SBC 5400 figure:
...
| Caption |
|---|
| 0 | Table |
|---|
| 1 | Rear Panel Description |
|---|
| 3 | Rear Panel Description |
|---|
|
Component | Cable Requirement | Description |
|---|
Alarm Port | Customer supplied cable | Alarm contact via a single shielded male HD15 connector. A single alarm port is present in SBC 5400 in platform.
This software release does not support the Alarm Port. | Management Ports | CAT5e cable | Four Copper copper Ethernet Ports which process Management traffic and perform protocol termination. | Locator | | Module identifier indicator | Media Ports | Single mode or Multi mode fiber Copper /copper CAT5e cable | Four copper SFP or fiber SFP ports for media and signaling traffic. | High Availability Ports | Single mode or Multi mode fiberCopper fiber/copper CAT5e cable (NON-CROSSOVER TYPE ONLY) | Two copper SFP or fiber SFP ports for redundancy synchronization traffic. The platform supports box level redundancy via communication paths provided by the external HA Ethernet ports. | Serial Port | Male DB9 connector | An RS-232 port used by BMC and control plane. The serial port uses a DB9 connector accessible from the rear panel. | Field Service Port | Copper CAT5e cable | A single Field Service Port. | Power Input | | Power Supply. The following are the descriptions of the power supply LED functions: - Off: No power input to the supply.
- Amber: Power supply fault.
- Blinking Amber: Main system power output fault.
- Blinking Green: Standby power to BMC is ON but main system power is not enabled.
- Solid Green: Both standby power to BMC and main system power are ON and OK.
|
|
...
| Caption |
|---|
| 0 | Table |
|---|
| 1 | Ethernet Port LEDs Description |
|---|
| 3 | Ethernet Port LEDs Description |
|---|
|
Port Type | Color | Description |
|---|
Mgmt0/Mgmt1/Mgmt2/Mgmt3 | GreenChecks if | - The Link LED is Solid Green when the link is up
and activity is - .
- The Activity LED is Flashing Green when there is activity present on the port.
- Solid Green = Link
- Flashing Green = Activity
| Media ports 0, 1, 2, and 3 | GreenChecks if | - The Link LED is Solid Green when the link is up
and activity is - .
- The Activity LED is Flashing Green when there is activity present on the port.
- Solid Green = Link
- Flashing Green = Activity
| HA ports 0 and 1 | GreenChecks if | - The Link LED is Solid Green when the link is up
and activity is - .
- The Activity LED is Flashing Green when there is activity present on the port.
- Solid Green = Link
- Flashing Green = Activity
| Field Service Port | GreenChecks if | - The Link LED is Solid Green when the link is up
and activity is - .
- The Activity LED is Flashing Green when there is activity present on the port.
- Solid Green = Link
- Flashing Green = Activity
|
|
Network Ports and Connection
The
The SBC 5400 chassis comprises the following external input and output ports:
...