Versions Compared

Old Version 7

changes.mady.by.user Ribbon Communications

Saved on

compared with

New Version 8

changes.mady.by.user Ribbon Communications

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

Add_workflow_for_techpubs
AUTH2
AUTH1
JIRAIDAUTHSBX-5221064339
REV5
REV6
REV3
REV1
REV2

Panel

In this section:

Table of Contents

Info
iconfalse

Related articles:

Static IP Routes for IP Interfaces

The staticRoute object is used to configure static IP routes for the IP interfaces. A static route indicates the nextHop gateway and IP interface that is used for a particular peer network IP prefix.

A route preference may be configured for static routes as shown in the command syntax. The lower the preference value, the more likely the route is to be used.

Notes
Noteinfo
icontitlefalse
Note
  1. Static routes using a specific ceName can only be added for packet interfaces.
  2. The SBC does not allow to delete the ceName separately.
  3. A static route is deleted only from the instance in which it is configured, and not from both active and standby instances of a
    Spacevars
    0product
    HA pair configuration.
  4. The configuration of a staticRoute with respect to a ceName cannot be edited. If any change is desired in the configuration, delete the staticRoute and reconfigure it.

 

Include Page
IP_IGs_ServedBySeperateProcessors
IP_IGs_ServedBySeperateProcessors

Command Syntax

Code Block
languagenone
% set addressContext <addressContext_name> staticRoute <destinationIpAddress> <ip_prefix_length> <nextHopIPaddress> <ipInterfaceGroupName> <ipInterfaceName> 
	condition ceName (node name)
	preference <100-2147483647>
 
% show addressContext <addressContext_name> staticRoute
 
% delete addressContext <addressContext> staticRoute <IpAddress>

Command Parameters

Caption
0Table
1Static Route Parameters

Parameter

Length/Range

Description

addressContext

1-23

<addressContext_name> – The name of the address context. The address context is a container of objects that correspond to a specific IP Addressing domain.

staticRoute

N/A

<destinationIpAddress><ENUM server Ip Address> – The destination IP address of the ENUM server. The following IP address types are supported:

  • IPv4 – This is V4 IP address in dotted decimal form (for example 128.127.50.224).
  • IPv6 – This is V6 IP address in hexadecimal/colon   form (for example, 1280:1276:3350:2224:2222:3333:8888:1245 or fd00:21:445:128::7880).

<ip_prefix_length>

0-128

The IP prefix length of this static route entry.

<nextHopIPaddress>

N/A

The IPv4 or IPv6 address of the next system en route to the destination.

<ipInterfaceGroupName>

N/A

The name of the IP interface group.

<ipInterfaceName>

N/A

The name of the IP interface for this entry.

conditionN/A

For an

Spacevars
0product
HA pair configuration (only), use this object to define the routes added to this
Spacevars
0product
HA pair.

  • ceName – The name of the computing element that hosts the port used by the IP interface (length: 1-255 characters).

NOTE: The

Spacevars
0product
supports only the ceName condition in this release.

NOTE: Before configuring the condition with a specific ceName, the ipInterfaceGroupName and ipInterfaceName parameters must first be configured for this Static Route. These three parameters cannot be configured using under the same commit command. For further details, refer to IP Interface Group - CLI.

NOTE: The condition option is only applicable to for non-management interfaces.

preference

100-2147483647

<preferenceNumber> (default = 100) – The route preference value. The management route preference range is 1-99 and the packet route preference range is greater than or equal to 100.

 

Command Example

To display static routes:

Code Block
languagenone
% show addressContext default staticRoute
staticRoute 10.6.30.105 32 10.34.26.1 LIF2 lif_eth3 {
    preference 10;
}
staticRoute 10.34.9.70 32 10.34.25.1 LIF1 lif_eth2 {
    preference 10;
}
staticRoute 10.34.9.95 32 10.34.26.1 LIF2 lif_eth3 {
    preference 10;
}
staticRoute 10.34.13.194 32 10.34.25.1 LIF1 lif_eth2 {
    preference 1;
}
staticRoute 10.34.13.195 32 10.34.26.1 LIF2 lif_eth3 {
    preference 10;

Static Route for Management Interfaces

The staticRoute object is used to configure static IP routes for the management interfaces. A static route indicates the nextHop gateway and management interface that is used for a particular peer network IP prefix.

Info
For details on Static IP Routes for Management interfaces, Refer to Management Static Route - CLI.

Pagebreak