Versions Compared

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

Noprint
Panel
borderColorblack
bgColororange
titleColorwhite
borderWidth3
titleBGColorblack
borderStyledashed
titleInternal NOTE:

Migration/Review to be done with respect to the ICD SBX-45806 Pathcheck Ping using ICMP.

Image Library - _Path_Check_Path

Add_workflow_for_techpubs
AUTH1sbsarkar
REV5bscoggins
REV6bscoggins
REV3snarayana
REV1dmuralimkeshavamurthy
REV2agogate

Panel

In this Section:

Table of Contents

Use the object Path Check Path to:

  • use the Internet Control Message Protocol (ICMP) to check if the remote entities are reachable.
  • generate and send the ping packets based on the configuration.
  • run up to 300 ping sessions simultaneously.
  • monitor the responses and validates if there is a failure due to specific conditions.


Info
titleNote

 

To View Path Check Path

  1. On the SBC main screen, navigate to All > System > Path Check Path.
  2. The Path Check Path window is displayed.

    Caption
    0Figure
    1Path Check Path

    Image Added

 

To Edit Path Check Path

  1. In the Path Check Path List window, select the Path Check Path that you want to edit by clicking the radio button adjacent to it.

    Caption
    0Figure
    1Select Path Check Path

    Image Added

  2. The Edit Selected Path Check Path window is displayed.

    Caption
    0Figure
    1Edit Selected Path Check Path

    Image Added

  3. Make changes and click Save to save the changes. Click Clear to cancel the changes.

 

To Copy Path Check Path

  1. In the Path Check Path List window, select the Path Check Path that you want to edit by clicking the radio button adjacent to it.

    Caption
    0Figure
    1Select Path Check Path

    Image Added

  2. Click Image Added in the Path Check Path List window.
  3. The Copy Selected Path Check Path window is displayed.

    Caption
    0Figure
    1Copy Selected Path Check Path

    Image Added

  4. Make changes and click Save to save the changes. Click Clear to cancel the changes.

 

To Create Path Check Path

  1. Click Image Added in the Path Check Path List window.
  2. The Create New Path Check Path window is displayed.

    Caption
    0Figure
    1Create New Path Check Path

    Image Added

  3. Make changes and click Save to save the changes. Click Clear to cancel the changes.

The parameters displayed in the Edit, Copy and Create tools are:

Caption
0Table
1Path Check Path - Parameter Description Table
ParameterDescription
NameThe name of the Path Check Path
Source IP AddressSpecifies the source IP address (IPv4/IPv6) of the ping patch.
Target IP AddressSpecifies the target IP address (IPv4/IPv6) of the ping patch.
Report Signal IP AddressSpecifies the reported signaling IP address (IPv4/IPv6) of the ping patch.
Report Signal IP PortSpecifies the reported signaling IP port (0-65535) of the ping patch.
Path Check ProfileSpecifies the name of the Path Check Profile on which the existing Path Check Path object is created.
Address ContextSpecifies the name of the Address Context on which the Path Check Path object is created.
ZoneSpecifies the name of the Zone on which the Path Check Path object is created.
IP Interface GroupSpecifies the name of the IP Interface Group where the corresponding IP Interface is present which triggers the ping.
IP InterfaceSpecifies the name of the IP Interface from which the ping must be generated.
State

Specifies the administrative state of Path Check Path object.

  • Disabled (default)
  • Enabled

Info
titleNote

To edit, copy or create a Path Check Path, ensure that the Path Check Profile selected from the drop-down list has its parameter Protocol set to Icmp. For more information on Path Check Profile, refer to Service Profiles - Path Check Profile

To Delete Path Check Path

  1. In the Path Check Path List window, select the Path Check Path that you want to edit by clicking the radio button adjacent to it.

    Caption
    0Figure
    1Select Path Check Path

    Image Added

  2. Click the delete symbol at the right end of the row containing the selected Path Check Path.
  3. The Delete pathCheckPath dialog-box is displayed.

    Caption
    0Figure
    1Delete Path Check Path

    Image Added

  4. Click Yes to confirm deletion, or No to cancel it.
  5. On successful deletion, a success message is displayed.
  6. Click Ok on the success message to complete the deletion process.
Migrate content here

 

Pagebreak