Versions Compared

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Panel

In this section:

Table of Contents
maxLevel2

The support of JIP parameter in SIP INVITE message enhances the 

Spacevars
0product
to support interworking of Jurisdiction information (JIP) for SIP-SIP and SIP-SIP-I and vice-versa including GW-GW by sending JIP in the PAI/FROM/PDCS header.
Spacevars
0product
can interwork JIP across gateway to GSX as well. 

Note

This feature is supported only with external PSX.

JIP information can be carried in the P-Asserted-ID/FROM/P-DCS-Billing-Info header of SIP INVITE message and in the PDCS header in 3xx response. 

Spacevars
0product
will record the JIP received information in the CDR.

Multiple controls can be enabled at a time to select the header or parameter from which JIP value will be extracted. The priority of extraction of JIP is as follows:

  • RN PARAMETER IN PAI
  • JIP PARAMETER IN PAI
  • RN PARAMETER IN FROM
  • JIP PARAMETER IN PDCS

To View Sip Jip Profile

 

Info
titleNote:

JIP handling is only supported when using an external PSX in the network.

The SBC supports sending Jurisdiction Information Parameter (JIP) information in SIP-SIP, SIP-SIP-I and SIP-I to SIP scenarios. A JIP value indicates the geographic location of the originating caller or switch. 

Use this window to configure SIP JIP profiles you can assign to ingress and egress SIP trunk groups. When SIP Jurisdiction Support is enabled for a trunk group, options in the SIP JIP profile determine what parameter to extract the SIP JIP value from in an incoming SIP INVITE message and in what parameter to place the JIP value in the outgoing message. The SBC can take the JIP value from or place it in the following parameters:

  • rn parameter in the PAID header
  • jip parameter in the PAID header
  • rn parameter in the From header
  • jip parameter in the P-DCS-Billing-Info header

Note that if you choose to enable more than one potential source from which to extract the JIP information, the SBC prioritizes them in the order listed above.

To View SIP JIP Profiles

On the

...

SBC main screen, go to Configuration > Profile Management > Category: Service Profiles >

...

SIP JIP Profile.

...

The

...

SIP JIP Profile window is displayed.

...

Caption
0Figure
1Profile Management - Service Profiles - Sip Ars Profile

Image Removed

To Edit Sip Jip Profile

...

A default profile, defaultJipProfile, is provided and assigned to SIP trunk groups by default. You have the option to create additional profiles and assign your own.

Caption
0Figure
1

...

Service Profiles -

...

Image Removed

SIP JIP Profile

Image Added

To Create a SIP JIP

The Edit Selected Sip Jip Profile window is displayed below.

Caption
0Figure
1Profile Management - Service Profiles - Sip Jip Profile Edit Window

Image Removed

Make the required changes and click Save at the right hand bottom of the panel to save the changes made.

...

Profile

To create a new

...

SIP JIP Profile:

  1. Click New SIP JIP Profile. The Create New SIP JIP Profile window opens. 

Caption
0Figure
1Profile Management - Service Profiles - Sip Jip Profile Fields

Image Removed

...

  1. Caption
    0Figure
    1

...

Image Removed

  1. Create New SIP JIP Profile Window

    Image Added

  2. Use the following table to specify the profile parameters and click Save.

...

Caption
0Table
1

...

SIP JIP Profile Parameters

Parameter

Description

Name

Specifies

...

a name

...

for the SIP JIP Profile.

Use

...

JIP From PAIrn

Specifies that when it is enabled, JIP information

...

can be extracted from the rn parameter in the PAI header of an INVITE message.The options are:

...

  • Disabled (default)
  • Enabled

Use

...

JIP From PAI JIP 

Specifies that when it is enabled, JIP information

...

can be extracted from the jip

...

parameter in the PAI header of an INVITE

...

message. The options are:

...

  • Disabled (default)
  • Enabled

Use

...

JIP From FROM

...

  

Specifies that when it is enabled, JIP information

...

can be extracted from the rn parameter in

...

the From header of an INVITE message. The options are:

...

  • Disabled (default)
  • Enabled

Use

...

JIP From PDCS 

Specifies that when it is enabled, JIP information

...

can be extracted from the jip parameter in

...

the PDCS header of an INVITE message.The options are:

...

  • Disabled (default)
  • Enabled
Send

...

JIP In

Specifies the

...

header and parameter

...

in which

...

JIP information should be sent in the outgoing INVITE message:

...

  • Rn PAI (default) - SBC will send the JIP value in rn parameter in PAI header.

...

  • JIP PAI - SBC will send the JIP value in jip parameter in PAI header.

...

  • Rn FROM - SBC will send the JIP value in rn parameter in FROM header.

...

  • JIP PDCS - SBC will send the JIP value in jip parameter in PDCS-Billing-Info header.

...

JIP Parameter As

Specifies the

...

parameter format in

...

which JIP information should be sent. The options are:

...

  • User Info (default)

...

  • URI Param

 

To Copy Sip Jip Profile

...

To Edit a SIP JIP Profile

You cannot edit the default SIP JIP profile, but you can edit a SIP JIP profile you created:

  1. Click the radio button next to the

...

  1. SIP JIP profile name. The Edit Selected SIP JIP Profile window opens.
  2. Make the required changes and click Save.

To Copy a SIP JIP Profile

To copy a SIP JIP Profile:

  1. Click the radio button next to the SIP JIP profile you want to copy.
  2. Click Copy SIP JIP Profile. The Copy Selected SIP JIP Profile window opens.
  3. Make any required changes and click Save.

To Delete a SIP JIP Profile

You cannot delete the default SIP JIP profile, but you can delete a SIP JIP profile you created:

  1. Click the radio button next to the SIP JIP profile you want to delete.
  2. Click the red X at the end of the row.
  3. Confirm the deletion when prompted
Caption
0Figure
1Profile Management - Service Profiles - Sip Jip Profile Highlighted

Image Removed

Click Copy Sip Jip Profile tab on the Sip Jip Profile List panel.

Caption
0Figure
1Profile Management - Service Profiles - Sip Jip Profile Fields

Image Removed

The Copy Selected Sip Jip Profile window is displayed along with the field details which can be edited.

Caption
0Figure
1Profile Management - Service Profiles - Sip Jip Profile Copy Window

Image Removed

Make the required changes to the required fields and click Save to save the changes. The copied Sip Jip Profile is displayed at the bottom of the original Sip Jip Profile in the Sip Jip Profile List panel.

To Delete Sip Jip Profile

To delete any of the created Sip Jip Profile, click the radio button next to the specific Sip Jip Profile which you want to delete.

Caption
0Figure
1Profile Management - Service Profiles - Sip Jip Profile Highlighted

Image Removed

Click Delete at the end of the highlighted row. A delete confirmation message appears seeking your decision.

Caption
0Figure
1Profile Management - Service Profiles - Sip Jip Profile Delete Confirmation

Image Removed

...

  1. .