Versions Compared

Old Version 1

changes.mady.by.user Ribbon Communications

Saved on

compared with

New Version 2

changes.mady.by.user Ribbon Communications

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

...

Note
As a best practice, always use UPPERCASE for trunk group names.

Command Syntax

Code Block
languagenone
% set addressContext <name> zone <name> sipTrunkGroup <name> services
	colocatedPandEcscf <disabled | enabled>
	dialogEventNotificationSupported <disabled |  enabled>
	disconnectTreatmentProfile <h323Default | sipDefault>
    dnsSupportType <a-only | a-srv-naptr>
    dynamicBlacklistProfile <profile name>
    emergencyCallHandlingMode <emergencyRegRequired | emergencyRegSupported | none | rejectWith380>
    emergencyCallProfile <profile name>
    honorSdpClockRate <disabled | enabled> 
    jsrcBandwidthReservation <disabled | enabled>
    longDurationCall 
        action <noAction | release | trap | trapAndRelease> 
        emergencyCalls <exclude | include> 
        relCause <#> 
        timeoutValue <0-44640 minutes>
    natTraversal 
        adaptiveLearning
            maxTcpPinholeTimer <60-65535>
            maxUdpPinholeTimer <60-65535>
            reLearningInterval <1-240>
            state <disabled | enabled> 
		iceSourceAddressFilterPriority
			serverReflexivePrefixLength <unsignedInt | 0..32>
        	state <disabled | enabled>
		iceSupport <none | iceWebrtc | iceLync | iceFull>
        learnNatForRtpOnly <disabled | enabled>
        mediaNat <disabled | enabled> 
        outboundTcpKeepaliveTimer <0-32767> 
        outboundUdpKeepaliveTimer <0-32767>
        qualifiedPrefix <IPv4 address> 
        secureMediaNatPrefix <0-32>
        signalingNat <disabled | enabled>
        tcpKeepaliveTimer <15-65535> 
        udpKeepaliveTimer <15-65535>
    overlapAddressing 
        minDigitsForQuery <#> 
        overlapState <disabled | enabled> 
        receive <InfoMethod | MultiInvite | disabled> 
        send <InfoMethod | MultiInvite | disabled> 
        timer1 <integer> 
        timer2 <integer> 
        timer3 <integer>
    preconditionIntwkUsing183 <disabled | enabled>
    preconditions <none | required | supported supported>| transparent>
    remoteEPreservation <disabled | enabled>
    resolvedDnsPrioritization <alwaysPrioritize | doNotPrioritize>
	sipArsProfile <profile name>
    sipJipProfile defaultJipProfile
    sipJurisdictionSupport <disabled | enabled>
    sipSecurityProfile <profile name>
    transmitPreconditions <none | required | supported>
    transparencyProfile <Transparency Profile name>  

Command Parameters

SIP Trunk Group Services Parameters

Caption
0Table
1SIP Trunk Group Services Parameters
 N/A N/AN/A N/A N/AN/AN/AN/AN/A
ParameterLength/RangeDescription
disconnectTreatmentProfileN/ADisconnect Treatment Profile name.
colocatedPandEcscf

Use this flag to support notification for a SUBSCRIBE with dialog event in this Trunk Group.

  • disabled (default)
  • enabled
dialogEventNotificationSupported

Use this flag to support co-locating P-CSCF and E-CSCF on the ingress Trunk Group.

  • disabled (default)
  • enabled
disconnectTreatmentProfileDisconnect Treatment Profile name.
dnsSupportTypednsSupportType

Indicates whether to use the DNS server for just A-record lookups, or for full NAPTR/SRV/A lookup as specified in RFC3263.

  • a-only
  • a-srv-naptr
dynamicBlacklistProfile N/ADynamic Blacklist Profile name.
emergencyCallHandlingMode N/A

Use this parameter to specify how to handle emergency calls.

  • emergencyRegRequired – Use this option to reject the emergency session establishment without an emergency registration.

    Note

    “usePsxRouteForEmergencyCall” must also be enabled to use this option.

  • emergencyRegSupported – Use this option when emergency registrations are supported, but emergency session establishment is possible without an emergency registration.

    Note

    “usePsxRouteForEmergencyCall” must also be enabled to use this option.

  • none (default) – Use this option when not using emergency registrations to perform PSX dip for registered user for emergency calls.

    Note

    “usePsxRouteForEmergencyCall” must also be enabled to use this option.

  • rejectWith380 – Use this option to reject an INVITE request with ‘380 Alternate Service’ response code from Ingress leg when the request is identified as emergency request and redirection flag is set to redirection mode.

See Emergency Registration for emergency registration functionality.

emergencyCallProfileEmergency Call Profile name.
honorSdpClockRateN/A

Enable this flag to map the DTMF Payload Type (PT) with the clock rate of the preferred or selected payload type for audio.

If the flag is disabled, all DTMF PTs except 8,000 Hz (both send and receive) are dropped.

  • disabled (default)
  • enabled
jsrcBandwidthReservation

Enable flag to require bandwidth reservation with Juniper Session Resource Controller.

  • disabled (default)
  • enabled
longDurationCall  N/A

The parameters associated with long duration call supervision.

  • action – This is the action to take if the long duration call timer expires. 
    • noAction (default) 
    • release 
    • trap 
    • trapAndRelease
  • emergencyCalls – Specifies whether Emergency Calls should be excluded from or included in Long Duration Call Disconnect procedures. 
    • exclude (default) 
    • include
  • relCause – The Q.850 release value to use should the call be released due to long duration call timer expiry. (default = 41).
  • timeoutValue – Timeout value (in minutes) of the long duration call timer. 
    • 0 (default) – Disable the timeout.
    • 1-44640 – Set the timeout to the specified value.
natTraversal
natTraversalSpecifies the various parameters associated with network-hosted NAT/NAPT traversal for SIP endpoints. Specify the following NAT Traversal parameters. See NAT Traversal Parameters table below for parameter details.
overlapAddressing

Parameters associated with overlap addressing support.

  • minDigitsForQuery – Minimum number of digits that need to be received before attempting to route the call. (range: 0-30 / default = 0).
  • overlapState – Specifies the whether to support or not support overlap addressing. 
    • disabled (default) 
    • enabled
  • receive  – Use this parameter to specify the Incoming overlap type.
    • InfoMethod – Select to support Info-based overlap dialing where initial INVITE with incomplete called party digits is answered locally by the SBC to establish early dialog, and subsequent digits are received through INFO message to complete dial sequence.
    • MultiInvite – Select to process multiple INVITEs for the same call with additional digits to complete the dial sequence.
    • disabled (default) – Select to disable this feature.
  • send – Use this parameter to specify the Outgoing overlap type.
    • InfoMethod – Select to support Info-based overlap dialing where initial INVITE with incomplete called party digits is answered locally by the SBC to establish early dialog, and subsequent digits are received through INFO message to complete dial sequence.
    • MultiInvite – Select to process multiple INVITEs for the same call with additional digits to complete the dial sequence.
    • disabled (default) – Select to disable this feature.
  • timer1 – Specifies the maximum time (in seconds) between collection of digits. (range: 5-15 / default = 10)
  • timer2 – Maximum time (in seconds) between sending an INVITE and receiving a backward message. (range: 0-14 / default = 0).
  • timer3 – Maximum time (in seconds) between receiving a 484 Address Incomplete message (if there are no outstanding INVITE transactions) and the receipt of fresh address information. (range: 4-64 / default = 4).
 preconditionIntwkUsing183 N/A

(This flag is for specific call flows and is not intended for generic use)

Enable this flag to locally generate first 183 responses for preconditions interworking before egressing INVITE. If disabled, these responses are dropped.

  • disabled (default)
  • enabled
Note

Do not enable preConditionIntwkUsing183 when End-to-End Prack is configured.

preconditionsN/AUse this parameter to level of preconditions support for incoming (only) requests.
  • none – (default)
  • required
    • supported) requests.
    • none – (default)
    • required
    • supported
    • transparent – Select this option to allow SBC to pass the received precondition option tag (either in require or supported) and precondition attributes present in SDP transparently.
    Note

    The transparent option must be configured on both Egress and Ingress legs.

    Info

    For precondition support of outgoing requests, see transmitPreconditions flag below.

    remoteEPreservationN/AEnable flag to require bandwidth reservation with the Juniper Session Resource Controller for the remote endpoint.
    • disabled (default)
    • enabled
    resolvedDnsPrioritizationN/A

    Use this parameter to control DNS prioritization for the specified SIP trunk group.

    • alwaysPrioritize – The SBC sends the requests in a dialog to the IP address where the INVITE was sent and the contact in the response message is an FQDN that resolves into multiple IP addresses.
    • doNotPrioritize – (default) The SBC latches on the first resolved IP address.

    sipArsProfile

    The name of the SIP ARS (Address Reachability Service) profile.

    sipJipProfileN/A

    defaultJipProfile – The default name of the SIP JIP profile to associate in egress and ingress SIP Trunk Groups.

    Note

    This parameter is only supported when the SBC is configured to use an external PSX.

    sipJurisdictionSupport

    Enable this flag to allow insertion of JIP parameter in SIP trunk group ingress and egress headers.

    • disabled (default)
    • enabled
    Note

    This flag is only supported when the SBC is configured to use an external PSX.


    sipSecurityProfileN/AThe name of the SIP Security Profile.
    transmitPreconditionsIndicates level of preconditions support for outgoing request/response.
    • none – When set to "none", 
      Spacevars
      0product
      does not add SIP precondition attributes in SDP of outgoing request even if attributes are present in the SDP of incoming requests.
    • required – Use this option to add SIP precondition attributes in SDP of outgoing request even if attributes are NOT present in the SDP of incoming requests. If precondition attributes are added by
      Spacevars
      0product
      , the local preconditions are set to ‘met’ and remote preconditions are set to ‘not-met’.
    • supported – (default) Use this option to ensure backward compatibility behavior. Use this option to add SIP precondition attributes in SDP of outgoing request only if attributes are present in the incoming request.
    transparencyProfileThe name of the Transparency Profile to associate with this SIP Trunk Group.

    Anchor
    nat
    nat
    NAT Traversal Parameters

     

    Parameters Description
    adaptiveLearningN/A

    Adaptive NAT pinhole learning parameters.

    • maxTcpPinholeTimer – Defines upper limit of the pinhole timeout for TCP in seconds. (range: 60-65535 / default = 600).
    • maxUdpPinholeTimer – Defines the upper limit of the pinhole timeout for UDP in seconds.  (range: 60-65535 / default = 180). 
    • reLearningInterval – Interval in hours at which the pinhole timeout is relearned. (range: 1-240 / default = 24). 
    • state– Enables/disables the adaptive nat pinhole timeout learning process for devices behind NAT. 
      • disabled (default) 
      • enabled
    iceSourceAddressFilterPriorityN/AEnable this parameter for the SBC to prioritize the processing of STUN packets matching the source addresses received in the candidate lines of the ICE SDP received from the peer during the STUN connectivity check phase.

    • serverReflexivePrefixLength – The length (in bits) of the prefix for server reflexive IP address (range: 0-32 / default = 16).

    • state – Administrative state of iceSourceAddressFilterPriority.

      • disabled
      • enabled (default)
    Info

    The filtering mechanism is applicable to the following RTP address types:

    • IPV4 Server Reflexive Address (for this address type, filtering is based on the provisioned Server Reflexive Prefix Length)
    • IPV4 Relay Address
    • IPV6 Relay Address
    • IPv6 Host Address

    Include Page
    iceSourceAddressFilterPriority_note
    iceSourceAddressFilterPriority_note

    iceSupport N/A

    This parameter indicates the type of ICE method used for STUN packet check.

    • none (default)

    • iceWebrtc – Use this attribute for WebRTC Gateway interworking. For example, using the Sonus WRTC Gateway, or in situations when the SBC is presented with an ICE SDP from a WebRTC-enabled Endpoint. When configured for this mode, SBC acts as a generic ICE-Lite agent.

    • iceLync – Use this attribute when interworking with a Microsoft Lync 2010 or 2013 client.

    • iceFull – Use this attribute when interworking with a full ICE client requiring the generation of a STUN connectivity check by the SBC in response to its own STUN connectivity check.

    Note

    The "iceFull" implementation is for lab use only in 5.0.0 release.

    Include Page
    ICE_note
    ICE_note

    See ICE-Lite Support for feature details.

    See Configuring SBC for WRTC for ICE-Lite configuration best practices.

     learnNatForRtpOnlyN/AEnable flag to learn media NAT from the first RTP packet only. If disabled, media NAT is learned from any first packet received. For egress trunk groups, this flag is applicable only if dynamicLRBT flag is disabled. If dynamicLRBT is enabled, NAPT learning occurs on arrival of RTP packet until the call is connected, at which point learnNatForRtpOnly applies even for egress Trunk Groups.

    • disabled (default) 

    • enabled

    Note

    The flag mediaNat must be enabled to use this flag.

    Note

    Do not enable learnNatForRtpOnly for SIP trunk groups with iceSupport enabled because it does not apply to ICE NAT traversal.

    mediaNat  Specifies the whether or not NAT/NAPT support is required for media. 
    • disabled (default) 
    • enabled
    Include Page
    ICE_note
    ICE_note
    outboundTcpKeepaliveTimer0-32767The NAT outbound keep-alive timer (in seconds) for SIP over TCP (default = 240)
    outboundUdpKeepaliveTimer0-32767The NAT outbound keepalive timer (in seconds) for SIP over UDP (default = 60)
    qualdifiedPrefix N/ASet of IP network media and signaling prefixes that an address must match to be considered for NAT handling. If there are no entries in qualifiedPrefixtable, the endpoint is treated as existing behind a NAT device. As a result, SBC considers requests from all IP addresses to be behind a NAT device.
    • ipAddress – IPv4 or IPv6 address. 
    • prefixLength – Value from 0-128 specifying the number of bits representing the network part of ipAddress.
    secureMediaNatPrefix 0-32Use this parameter to match up to 'N' bits of the network IPv4 address obtained from signaling. If set to "0", feature is disabled, and no match of network IP address will occur. (default = 0)
    signalingNat N/AThis indicates whether or not NAT/NAPT support is required for signaling. 
    • disabled (default)
    • enabled
    tcpKeepaliveTimer15-65535This NAT TCP keep-alive timer sets the registration refresh rate (in seconds) for SIP over TCP. (default = 240).
     udpKeepaliveTimer 15-65535

    This NAT UDP keep-alive timer sets the registration refresh rate (in seconds) for SIP over UDP. (default = 60).

    Pagebreak