Versions Compared

Old Version 10

changes.mady.by.user Ribbon Communications

Saved on

compared with

New Version 11

changes.mady.by.user Ribbon Communications

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Comment: corrected typo per comment from Anurodh

Add_workflow_for_techpubs
AUTH1
JIRAIDAUTHSBX-89465
REV5
REV6
REV3
REV1

Panel

In this section:

Table of Contents
maxLevel4

Info
iconfalse

Related articles:

Use this command to configure custom SWe traffic profiles. Use SBC SWe traffic profiles to characterize the call mix you expect to occur on your SBC SWe system. SBC SWe systems can enhance their VM performance by allocating CPU cores in a manner that maximizes capacity for the call mix specified in the active traffic profile.

Command Syntax

Code Block
% set system SweTrafficProfilessweTrafficProfiles <profile name> 
      bhcaPerSubscriber <attempts>
      callHoldTime <seconds>
      cryptoPercent <percent>
      externalRefreshTimer <seconds>
      internalRefreshTimer <seconds>
      isAccess <false | true>
      mediaCostFactor <media factor>
      passthroughCodecProfile <profile name>
      processorCapabilityIndexOverride <false | true>
      processorCapabilityIndexOverrideValue <processor factor>
      rxPPSFactor <Rx PPS factor>
      sigCostFactor <signaling factor>
      tonesPercent <percent>
      transcodePercent <percent>
      txPPSFactor <Tx PPS factor>
      useGPUForTranscoding <false | true>

Command Parameters

Div
classpdf8pttext

Caption
0Table
1SWe Traffic Profile Parameter Descriptions
ParameterLength/RangeDescription
sweTrafficProfiles1-40 characters

<profile name> – Enter a unique SWe Traffic Profile name.

NOTE: The SBC SWe supports up to 20 SWe Traffic Profiles. To create additional profiles, delete any inactive custom profiles.

bhcaPerSubscriber0-5

<attempts> (default = 1) – Indicates busy hour call attempts (BHCA) per subscriber.

NOTE: This parameter is available when accessScenario = "true".

callHoldTime

10-10800<seconds> – Enter the average call hold time, in seconds, of the call load for this profile. (default = 90)
cryptoPercent0-100

<% value> (default = 0) – The percentage of media sessions (including both transcoding and passthrough) requiring cryptographic treatment.The value is 50 when there is SRTP<->RTP interworking on all calls.

directMediaPercent0-100

<% value> (default 0) – The call load percentage for direct media, which can never be converted to pass-through calls

NOTE: The combined total percentage of directMediaPercent and transcodePercent should not exceed 100%.

externalRefreshTimer15–86400

<seconds> (default = 1800) – Use this parameter to specify the external registration timer, in seconds.

NOTE: The parameter is available only when isAccess is set to "true".

internalRefreshTimer15-86400

<seconds> (default = 1800) – Use this parameter to specify the internal registration timer, in seconds.

NOTE: The parameter is available only when isAccess is set to "true".

isAccessN/A

Set this flag to "true" to specify whether the deployment uses an access scenario.

  • false (default)
  • true

NOTE: When set to 'true', internalRefreshTimer, registrationRefreshInterval and bhcaPerSubscriber parameters are available for configuration.

mediaCostFactor0.0001 to 100Use this parameter to specify a media cost factor to use during capacity estimation. This factor affects the media plane estimation,such as crypto session and pass-through session estimation (default = 1). This parameter is applicable only to custom profiles.
passthroughCodecProfileN/A

The name of the codec mix to associate with the Passthrough Codec Profile.

  • G711_20ms
  • G711_G729_20ms
processorCapabilityIndexOverrideN/A

Use this flag to enable/disable index overriding of the default CPU performance computation by the SBC SWe. When set to 'true', the computed indices (which are calculated during system boot-up) are ignored, and the value provided in processorCapabilityIndexOverrideValue attribute is used for all estimations.

  • false (default)
  • true

NOTE: Since use cases for overriding the default computed indices are rare, it is recommended to not set the value of processorCapabilityIndexOverride to "true" to avoid inaccurate session numbers and vCPU computations.

processorCapabilityIndexOverrideValue0.2-10

Use this parameter to specify the computational value to use to override the default computed indices. (default = 1)

NOTE: This parameter is available when processorCapabilityIndexOverride is set to "true". The value given should be in 0.2 to 10.

sigCostFactor0.0001 to 100Use this parameter to specify a signaling cost factor to use during capacity estimation. This factor affects the signaling plane estimation, such as cps estimation (default = 1). This parameter is applicable only to custom profiles.
rxPPSFactor1.0 to 100Use this parameter to specify a received (rx) PPS factor to use during capacity estimation (default = 1). This parameter is applicable only to custom profiles.
tonesPercent0-100<% value> (default = 0) – Use this parameter to specify the percentage of legs to use for tones treatment.
transcodePercent0-100

<% value> (default = 0) – Use this parameter to specify the percentage of call load to use for transcoded calls.

NOTE: The combined total percentage of directMediaPercent and transcodePercent should not exceed 100%.

transcodingCodecProfileN/A

The name of the codec mix to associate with the Transcoding Codec Profile.

  • G711_20ms
  • G711_G729_20ms
txPPSFactor1.0 to 100Use this parameter to specify a transmitted (tx) PPS factor to use during capacity estimation. Use the Rx/Tx parameters for scenarios such as SIPREC where the received/transmitted PPS may not be the same (asymmetric) (default = 1). This parameter is applicable only to custom profiles.

useGPUForTranscoding

 N/A

 Use to specify the type of transcoding, GPU (true) or CPU (false).

  • false (default)
  • true

Command Example

  1. The following CLI command creates a custom SWe trafic profile named custom1 that includes media and signaling cost factors and asymmetric Tx/Rx PPS factors to use in generating capacity estimates.

    Code Block
    % set system sweTrafficProfiles custom1 isAccess true bhcaPerSubscriber 2.5 transcodePercent 30 callHoldTime 60 internalRefreshTimer 3000 externalRefreshTimer 2500 tonesPercent 15 processorCapabilityIndexOverride false mediaCostFactor 1.5 sigCostFactor 1.5 txPPSFactor 1.2 rxPPSFactor 1.0
commit

  2. Create a codec mix profile, customCodecMix.

    Code Block
    % set system sweCodecMixProfile customCodecMix g723 p20 percentage 50
% set system sweCodecMixProfile customCodecMix g711 p20 percentage 30
% set system sweCodecMixProfile customCodecMix g729 p10 percentage 20
commit

  3. Attach the codec mix profile to the SWe traffic profile.

    Code Block
    % set system sweTrafficProfiles custom1 passthroughCodecProfile G711_20ms transcodePercent 30 transcodingCodecProfile customCodecMix
commit

Pagebreak