Page History

filterAdmin

Event Log Class Filter configuration table.

<node name>

SBC node name.

<event type>

The type of event log to configure:

• audit – System audit data. These files contain a record of all management interactions that modify the state of the system, and includes all the changes made via the CLI and the Netconf interface. These files use .AUD extensions.
• debug – System debugging data. These files have .DBG extensions.
• security – Security level events. These files have .SEC extensions.
• system – System level events. These files have .SYS extensions.
• trace – System trace data. These files have .TRC extensions.

<event class>

For each event type, configure one of the following event:

• audit – Audit subsystem.
• callproc – Call Processing subsystem.
• directory – Directory Services subsystem.
• netmgmt – Network Management subsystem.
• policy – Policy subsystem.
• resmgmt – Resource Management subsystem.
• routing – Network Routing subsystem.
• security – Security subsystem.
• signaling – Signaling subsystem.
• sysmgmt – System Management subsystem.
• trace – Call Trace subsystem.

level

Minimum severity level threshold for event logging:

• critical – log only critical events.
• info – log all events.
• major – log major and critical events.
• minor – log all events other than info.
• noevents – do not log any events.

NOTE:  Info level logs which are traps or faults are always reported in the system logs.

state

Administrative state of event logging for this event type. Set to “on” if filter entry should take precedence over per-node settings.

• off (default) – Logging is not activated.
• on – Logging is activated.

filterStatus

Event log class filter status table.

<system name>

SBC system name.

<event type>

The type of event log:

• audit – System audit data. These files contain a record of all management interactions that modify the state of the system, and includes all the changes made via the CLI and the Netconf interface. These files use .AUD extensions.
• debug – System debugging data. These files have .DBG extensions.
• security – Security level events. These files have .SEC extensions.
• system – System level events. These files have .SYS extensions.
• trace – System trace data. These files have .TRC extensions.

<event class>

Event class for each event type:

• audit – Audit subsystem.
• callproc – Call Processing subsystem.
• directory – Directory Services subsystem.
• netmgmt – Network Management subsystem.
• policy – Policy subsystem.
• resmgmt – Resource Management subsystem.
• routing – Network Routing subsystem.
• security – Security subsystem.
• signaling – Signaling subsystem.
• sysmgmt – System Management subsystem.
• trace – Call Trace subsystem.

resetStats

Use this control to reset the value of Events Filtered column of the filterStatus display.

clearInfoLevelLoggingDisabled

Use this command to re-enable info level logging after it becomes disabled due to system congestion. If this command is executed while the system is still congested, this may cause the system to become further congested.

NOTE: Only issue this command once system congestion dissipates. The system may become further congested if this command is executed while the system is still congested

state

Enable this flag to measure the memory usage of each active process.

• disable (default)

• enable

Specifies the level of details to be displayed.

• summary (default)
• detailed

The time interval, in minutes, to elapse between the recording of each memory usage file to the hard drive. (Default = 5)

NOTE: An interval of 1440 minutes (24 hours) equates to one log entry per day for a process.

platformAuditLogs


Use this command to enable/disable platform audit logging of administrative, privileged, and security actions.

• state
  • disabled (default)
  • enabled

subsystemAdmin

Subsystem event logging configuration.

<system_name>

Name of system.

<subsys_ID>

The subsystem/task ID. See Subsystem IDs table below for a list of subsystem IDs. 

infoLogState

Use this flag to enable/disable event logging of INFO level messages to DBG and SYS logs for   the specified subsystem. By default, infoLogSate is enabled for all subsystems.

• disabled
• enabled (default)

NOTE:

• If infoLogState is disabled for CHM, nothing is written to AUD logs.
• If infoLogState is disabled for CPX, request commands are not recorded to AUD logs.

typeAdmin

N/A

Event Log configuration table for configuration items related to each Event Log type.

<event_type>

N/A

Specifies the type of event log being configured:

• acct – System account data. These files have .ACT extensions.
• audit – System audit data. These files contain a record of all management interactions that modify the state of the system. These files have .AUD extensions. It  includes   all the changes made via the CLI and the Netconf interface. (This attribute is only available to an Administrator)
• debug – System debugging data. These files have .DBG extensions.
• packet – Packet information details. These files have .PKT extensions. If enabled, stores the packet details to .PKT files.
• security – Security level events. These files have .SEC extensions. (This attribute is only available to an Administrator)
• system – System   level events. These files have .SYS extensions.
• trace – System trace data. These files have .TRC extensions.

NOTE: Syslog is not supported for acct and packet event types.

fileCount

1-2048

Specifies the number of event log files that will be maintained for this event type. (default = 32).

fileSize

256-65535

Maximum size (in KB) that a single event log file will ever grow to. (default = 2048).

fileWriteMode

N/A

Event log NFS write mode. 

• default – Log data is written as a 1344-byte packet.
• optimize – Log data is written as a 8000-byte packet. Optimize write mode results in IP fragmentation but yields better throughput.

filterLevel

N/A

Events that are at least as severe as the designated level will be logged.

• critical – log only events of this threshold.
• info – log every possible event.
• major – log major and critical events only.
• minor – log all events other than information.
• noevents – do not log any events.

NOTE: The command to set the filterLevel for the acct event type is no longer applicable.

messageQueueSize

2-32

The number of event log message entries to buffer before writing to disk. (default = 10).

renameOpenFiles

N/A

Enable this flag to append an ".OPEN" extension to accounting and files which are open for writing.

• disabled (default)
• enabled

NOTE:You must enable the global callTrace signalingPacketCapture parameter (set state to "enable") to capture SIP and H.323 packets (Refer to Call Trace - CLI for configuration details).

Once signalingPacketCapture is enabled, any subsequent changes to SBC device configurations or filter information will not be available to signaling packet captures until signalingPacketCapture is reset (state is disabled, and then re-enabled).

rolloverAction

N/A

Event log rollover actions.

• start – Start rollover action
• stop – Stop rollover action

rolloverInterval

0-31536000

Event log rollover interval, in seconds.

rolloverStartTime

N/A

Specifies the start time for event log rollover. The format is CCYY-MM-DDTHH:MM:SS. For example: 2010-01-01T01:01:01

rolloverType

N/A

Event log rollover type. 

• nonrepetitive (default) – The rollover will occur once at the specified single instance.
• repetitive – The rollover will occur repeatedly at the specified intervals.

saveTo

N/A

Use flag to specify that the events are saved to disk or not saved.

• disk (default)
• none

state

N/A

Specifies the requested state of the given Event Log type.

• disabled – Logging is not activated.
• enabled – (default) Logging is activated.
• rollfile

 Accounting logs cannot be disabled.

syslogRemoteHost

0-255

The remote host where the messages are written to the syslog.

syslogRemotePort

1-65535

Specifies the port to use to send messages to the remote syslog. Default value is 514.

syslogRemoteProtocol

N/A

The protocol to use to send messages to the remote syslog.

• relp
• tcp (default)
• udp

syslogState

N/A

Enable flag to log events of specified type to syslog.

• disabled (default)
• enabled

typeAdmin

Event Log configuration table for configuration items related to each Event Log type.

<event_type>

Specifies the type of event log to roll over:

• acct – System account data. These files have .ACT extensions.
• audit – System audit data. These files contain a record of all management interactions that modify the state of the system. These files have .AUD extensions. It  includes   all the changes made via the CLI and the Netconf interface. (This attribute is only available to an Administrator)
• debug – System debugging data. These files have .DBG extensions.
• packet – Packet information details. These files have .PKT extensions. If enabled, stores the packet details to .PKT files.
• security – Security level events. These files have .SEC extensions. (This attribute is only available to an Administrator)
• system – System   level events. These files have .SYS extensions.
• trace – System trace data. These files have .TRC extensions.

rolloverLogNow

This control is used with request command to perform a roll-over of the specified log immediately.