Versions Compared

Old Version 8

changes.mady.by.user Ribbon Communications

Saved on

compared with

New Version 9

changes.mady.by.user Ribbon Communications

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

...

To View and Edit CAC - Ingress

On the the 

Spacevars
0product
 main screen, go to to Configuration >  > System Provisioning > Category > Category: Trunk Provisioning Provisioning > Trunk  Trunk Group >  > SIP Trunk Group > CAC >  > CAC > Ingress. The Ingress window is displayed.

...

The Edit Ingress window is displayed.

 

Caption
0Figure
1SIP Trunk Group - CAC Ingress Edit Window

 Image Added

Note: An example dialog box is shown here. Refer to the Table below for model-specific allowed values (blue font in the example) for Call Rate Max and Call Burst Max.

Image Removed 

 

The following fields are displayed:

Caption
0Table
1CAC - Ingress Parameters
 

Note: You can set both “callBurstMax” and “CallRateMax” as unlimited; however, if you assign a value to one parameter, the other must also be assigned a value.

Parameter

Description

Call Rate Max

Specifies the value of maximum sustained ingress call rate allowed burst in calls per second. (range: 1/second (above the allowed sustained rate) for egress call attempts.

SBC 5xx0 / 5400 / SWe - Range: 1-450, or unlimited. (The default value is unlimited.)

SBC 7000 - Range: 1-1,350, or unlimited. (The default value is unlimited.)

.

Note
Call Burst Max

Specifies the value of maximum allowed burst

size

(above the allowed sustained rate) for

ingress

egress call attempts

,

in calls

per

/second.

(range

 

SBC 5xx0/5400 / SWe - Range: 1-900, or unlimited. (The default value is unlimited.)

SBC 7000 - Range: 1-2,700, or unlimited. (The default value is unlimited.)

Note: You can set both “callBurstMax” and “CallRateMax” as unlimited; however, if you assign a value to one parameter, the other must also be assigned a value.

Register Rate Max

Specifies the maximum sustained ingress rate (registrations per second) of initial SIP registrations allowed. (range: 1-1000, or unlimited.

Spacevars
0series2
range is 1-3000, or unlimited.)

note

 

Note: You can set both “registerBurstMax” and “registerRateMax” as unlimited; however, if you assign a value a value to one parameter, the other must also be assigned a value.

Register Burst Max

Specifies the maximum allowed burst (above the allowed sustained rate) for ingress initial SIP registrations. (range: 1-1000, or unlimited.

Spacevars
0series2
range is 1-3000, or unlimited)

Call Limit

Specifies the total number of concurrent calls (either ingress or egress) allowed on ingress. The value ranges from 0 to 2147483647 or unlimited (default).

Emergency Oversubscription

Specifies the oversubscription of resources (as a percentage) that is allowed for emergency calls. The value ranges from 0 to 1000 and the default value is 10.

Extended Emergency IP Limit

The resource oversubscription (expressed as numeric value) allowed for emergency calls. The value ranges from 0 to 40000 with a default value of 0.

Subscribe Rate Max

Specifies the maximum sustained ingress rate (subscribes per second) of initial SIP subscribe request. (range: 1-1000, or unlimited.
Spacevars
0series2
range is 1-3000, or unlimited)
Subscribe Burst MaxSpecifies the maximum allowed burst (above the allowed sustained rate) for ingress initial SIP subscribe request. (range: 1-1000, or unlimited.
Spacevars
0series2
range is 1-3000, or unlimited)

Other Req Rate Max

Specifies the maximum sustained ingress rate (requests per second) of other out-of-dialog SIP requests. (range: 1-1000, or unlimited.

Spacevars
0series2
range is 1-3000, or unlimited).

Other Req Burst Max

Specifies the maximum allowed burst (above the allowed sustained rate) for any other ingress out-of-dialog SIP request. (range: 1-1000, or unlimited.

Spacevars
0series2
range is 1-3000, or unlimited).

Hpc OversubscriptionSpecifies the over-subscription of the resources (in a percentage) that is allowed for HPC calls. When the baseline call limit and bandwidth limits are reached, normal calls are not admitted, but additional HPC calls are allowed up to the configured value percentage. The value ranges from 0 to 100 % and the default value is 10 %.

Make the required changes and click click Save at  at the right hand bottom of the panel to save the changes made.

...