The
supports Rx interface which pertains to QoS resource reservation for reserving bandwidth in the IP access network. The Rx reference point is used to exchange application level session information between the Policy and Charging Rules Function (PCRF) and the P-CSCF. The Access Solution, acting as P-CSCF creates a TCP connection with the configured PCRF.
| Note |
|---|
Do not configure PCRF on the Egress leg of the Trunk Group for REGISTER. |
| Include Page |
|---|
| IP_IGs_ServedBySeperateProcessors |
|---|
| IP_IGs_ServedBySeperateProcessors |
|---|
|
| Note |
|---|
Only one instance of Diam Node can be created. |
| Note |
|---|
When configuring a Diameter Node in an HA configuration, the "Secondary Origin Host" parameter must be configured with the Standby hostname |
To View Diam Node
On the
main screen, navigate to
All >
Address Context >
Diam Node.
The Diam Node can be checked for each Address Context or for all the Address Contexts created. Use the drop-down box to select the desired Address Context.
| Caption |
|---|
| 0 | Figure |
|---|
| 1 | All - Address Context - Diam Node Main Field |
|---|
|
|
The Diam Node window is displayed.
| Caption |
|---|
| 0 | Figure |
|---|
| 1 | All - Address Context - Diam Node |
|---|
|
|
To Edit Diam Node
To edit any of the Diam Node in the list, click the radio button next to the specific Diam Node name.
| Caption |
|---|
| 0 | Figure |
|---|
| 1 | All - Address Context - Diam Node Highlighted |
|---|
|
|
The Edit Selected Diam Node window is displayed below.
| Caption |
|---|
| 0 | Figure |
|---|
| 1 | All - Address Context - Diam Node Edit Window |
|---|
|
|
Make the required changes and click Save at the right hand bottom of the panel to save the changes made.
To Create Diam Node
To create a new Diam Node, click New Diam Node tab on the Diam Node List panel.
| Caption |
|---|
| 0 | Figure |
|---|
| 1 | All - Address Context - Diam Node Fields |
|---|
|
|
The Create New Diam Node window is displayed.
| Caption |
|---|
| 0 | Figure |
|---|
| 1 | All - Address Context - Diam Node Create Window |
|---|
|
|
The following fields are displayed:
| Caption |
|---|
| 0 | Table |
|---|
| 1 | Diam Node Parameters |
|---|
|
Parameter | Length/Range | Description |
|---|
Name | 1-23 characters | The Specifies the name of this Diameter Node. The value ranges up to 23 characters. | Origin Realm | 1-128 characters | The Specifies the description of the origin realm of this node. The value ranges up to 128 characters. | Primary Origin
HostHost | 1-128 characters | The Specifies the description of the primary origin of this node. The value ranges up to 128 characters. |
Secondary Origin Host | 1-128 characters | The Specifies the description of the secondary origin of this node. The value ranges up to 128 characters. | Transaction
TimeoutTimeout | 500-6000 | The Specifies the time out value in milli seconds. The value ranges from 500 to 6000 and the default value is milliseconds, with a default value of 1000. | State | N/A | The Specifies the state of the Diameter Node. The options are: - Disabled
enableddisabled (default)- Enabled
| Dump Pdu | N/A | When enabled, SBC logs the DIAMETER PDU sent and received on the Rx interface to the debug log. The options are: - Disabled
enableddisabled (default)- Enabled
| IP
Interface Group Name | N/A | The Specifies the name of the IP Interface group used by this node. | IP V4Address | N/A | The Specifies the IPv4 address used to create connections towards peer. | IP V6Address | N/A | The Specifies the IPv6 address used to create connections towards peer. |
|
To Delete Diam Node
To delete any of the created Diam Node, click the radio button next to the specific Diam Node which you want to delete.
| Caption |
|---|
| 0 | Figure |
|---|
| 1 | All - Address Context - Diam Node Highlighted |
|---|
|
|
Click Delete at the end of the highlighted row. A delete confirmation message appears seeking your decision.
| Caption |
|---|
| 0 | Figure |
|---|
| 1 | All - Address Context - Diam Node Delete Confirmation |
|---|
|
|
Click Yes to remove the specific Diam Node from the list.