Versions Compared

Old Version 6

changes.mady.by.user Ribbon Communications

Saved on

compared with

New Version 7

changes.mady.by.user Ribbon Communications

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Panel

In this section:

Table of Contents
maxLevel2

 

The ConnexIP Operating System jump start installation is required in cases such as, reverting to older releases, SSD drive replacement. To re-install ConnexIP OS, follow the procedure below:

Note

The ConnexIP ISO installation procedure automatically copies the SBC application package to the SBC platforms.

Note

The ConnexIP ISO installation procedure takes around 30 to 40 minutes to complete.

Downloading ConnexIP ISO Image

Download the following ConnexIP OS files bundled from the Sonus Salesforce customer portal:

  • sbc-V06.00.00R000-connexip-os_03.0204.00-R000_amd64.iso
  • sbc-V06.00.00R000-connexip-os_03.0204.00-R000_amd64.iso.md5

Refer to Downloading the Software from Salesforce to know more.

To determine the exact OS versions, refer the appropriate release notes at SBC Release Information.

Installing OS

 

Info

Reinstalling the OS will format your disk and erase all data. Sonus highly recommends saving the configuration data to a temporary directory on the remote server before reinstalling the OS in the event you need to restore the original configuration data after the re-installation.

The following procedure describes how to reinstall the ConnexIP OS:

  1. Launch the host remote console through the BMC. Refer to Launching the Remote Console from the BMC.

  2. Select Media in the JViewer and click Virtual Media Wizard.

    Caption
    0Figure
    1Virtual Media Wizard

  3. The Virtual Media screen appears. Select ISO Image from CD/DVD Media1 section of the screen.

    Caption
    0Figure
    1Virtual Media Screen

  4. Click Browse. From the Open dialog, browse to and select the connexip-os_<version>_amd64.iso file and click Open.

    Caption
    0Figure
    1Open Dialog Screen

  5. Click Connect CD/DVD. A message Device redirected in Read Only Mode appears on the screen. Click OK to continue. This mounts the ISO image from your local desktop or laptop.

    Caption
    0Figure
    1Mounting Virtual CD/DVD

  6. Click Close.

  7. Reboot the system from JViewer by executing the following command:
    # reboot

  8.  After few minutes, the splash screen appears. Press <Del> or <Esc> key immediately to enter into BIOS configuration screen.

    Caption
    0Figure
    1BIOS Splash Screen

  9. The BIOS setup utility screen displays. Use right arrow key to navigate to the Save & Exit menu.

    Caption
    0Figure
    1BIOS Setup Utility

  10. Select AMI Virtual CDROM0 1.00 from Save & Exit menu to boot from the virtual CD drive. This instructs the server to boot from the redirected ConnexIP OS ISO image.

    Caption
    0Figure
    1Booting from Virtual CD Drive

  11. Select Install and press <Enter> to start the installation.

    Caption
    0Figure
    1Sonus ConnexIP Installer Boot Menu

  12. Select American English and press <Enter>.

    Caption
    0Figure
    1Keymap Menu

  13. The automated installation process starts. This process takes approximately 30 to 40 minutes.

    Caption
    0Figure
    1Partitions Formatting Screen

    Caption
    0Figure
    1Installing the Base System

    Caption
    0Figure
    1Selecting and Installing Software

    Caption
    0Figure
    1Copying SBC Package

    Caption
    0Figure
    1Running Post Install


    Once the installation is complete, the disk partition upgrade starts. At this stage, DO NOT power off the system.

    Caption
    0Figure
    1Disk Partitioning


    Once the system reboots, the ConnexIP login screen appears on the screen.

    Caption
    0Figure
    1ConnexIP Login Screen

    This concludes the ConnexIP OS Installation/Re-installation process.

  14. Close the JViewer window.

Continue to install the desired SBC Application build. Refer to Installing SBC Application to know more.

 

Pagebreak