Versions Compared

Old Version 5

changes.mady.by.user Ribbon Communications

Saved on

compared with

New Version 6

changes.mady.by.user Ribbon Communications

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

...

Multiexcerpt
MultiExcerptNamefilterAdmin
Caption
0Table
1Filter Admin Event Log Parameters
3Filter Admin Event Log Parameters

 

Parameter

Description

Mandatory parameters:

filterAdmin

Event Log Class Filter configuration table.

<node name>

SBC node name.

<event type>

The type of event log to configure:

  • audit – System audit data. These files contain a record of all management interactions that modify the state of the system, and includes all the changes made via the CLI and the Netconf interface. These files use .AUD extensions.
  • debug – System debugging data. These files have .DBG extensions.
  • security – Security level events. These files have .SEC extensions.
  • system – System level events. These files have .SYS extensions.
  • trace – System trace data. These files have .TRC extensions.

<event class>

For each event type, configure one of the following event:

  • audit – Audit subsystem.
  • callproc – Call Processing subsystem.
  • directory – Directory Services subsystem.
  • netmgmt – Network Management subsystem.
  • policy – Policy subsystem.
  • resmgmt – Resource Management subsystem.
  • routing – Network Routing subsystem.
  • security – Security subsystem.
  • signaling – Signaling subsystem.
  • sysmgmt – System Management subsystem.
  • trace – Call Trace subsystem.

level

Minimum severity level threshold for event logging:

  • critical – log only critical events.
  • info – log all events.
  • major – log major and critical events.
  • minor – log all events other than info.
  • noevents – do not log any events.
Note

 Info level logs which are traps or faults are always reported in the system logs.

state

Administrative state of event logging for this event type. Set to “on” if filter entry should take precedence over per-node settings.

  • off (default) – Logging is not activated.
  • on – Logging is activated.
Noprint

Back To Top

Anchor
FilterStatus
FilterStatus
Filter Status

...

Multiexcerpt
MultiExcerptNameinfoLevelLoggingEnable
Caption
0Table
1Info Level Logging Enable Event Log Parameter

 

Parameter

Description

clearInfoLevelLoggingDisabled

Use this command to re-enable info level logging after it becomes disabled due to system congestion. If this command is executed while the system is still congested, this may cause the system to become further congested.

Note

Only issue this command once system congestion dissipates. The system may become further congested if this command is executed while the system is still congested.

Anchor
PlatformAuditLogs
PlatformAuditLogs
Platform Audit Logs

...

The subsystem's maximum event ID to not filter
Multiexcerpt
MultiExcerptNamesubsystemAdmin
Caption
0Table
1Subsystem Admin Event Log Parameters

 

Parameter

Length/Range

Description

subsystemAdmin

N/A

Subsystem event logging configuration.

Mandatory parameters:

<system_name>

N/A

Name of system.

<subsys_ID>

N/A

The subsystem/task ID. See table below for a list of subsystem IDs. 

Non-mandatory parameters:

infoLogState

N/A

Use this flag to enable/disable event logging of INFO level messages to DBG and SYS logs for   the specified subsystem. By default, infoLogSate is enabled for all subsystems.

  • disabled
  • enabled (default)
Note
  • If infoLogState is disabled for CHM, nothing is written to AUD logs.
  • If infoLogState is disabled for CPX, request commands are not recorded to AUD logs
.

maxEventId

N/A

  • .
minEventId

N/A

The subsystem's minimum event ID to not filter.

Caption
0Table
1Subsystem IDs
3ids

acm     

arma    

asg     

atmrm  

brm    

cam     

cassg   

cc      

chm 

cli     

cmtsg    

cnh     

cpx    

dbug   

diamc     

dnsc    

drm 

ds 

ema     

enm 

fm      

frm    

grm    

gwfe      

gwsg    

h323sg  

icmsvc   

ike     

im     

ipacl  

ipm       

lvm   

mgsg 

mtp2    

mtrm     

ncm    

ncomm  

nim   

nrm     

nrma      

nrs 

ntp     

pathchk  

pes     

pfa    

pipe   

pipehook  

prm     

reserved  

rtcp 

rtm     

scpa     

sec     

sfm    

sg 

sgisdn    

sgisup  

sipfe     

sipsg 

sm      

sma      

ssa     

trm    

xrm 

 

 

...

Multiexcerpt
MultiExcerptNametypeAdmin1
Caption
0Table
1Type Admin Event Log Parameters (set command)

 

Parameter

Length/Range

Description

typeAdmin

N/A

Event Log configuration table for configuration items related to each Event Log type.

<event_type>

N/A

Specifies the type of event log being configured:

  • acct – System account data. These files have .ACT extensions.
  • audit – System audit data. These files contain a record of all management interactions that modify the state of the system. These files have .AUD extensions. It  includes   all the changes made via the CLI and the Netconf interface. (This attribute is only available to an Administrator)
  • debug – System debugging data. These files have .DBG extensions.
  • packet – Packet information details. These files have .PKT extensions. If enabled, stores the packet details to .PKT files.
  • security – Security level events. These files have .SEC extensions. (This attribute is only available to an Administrator)
  • system – System   level events. These files have .SYS extensions.
  • trace – System trace data. These files have .TRC extensions.
Note

Syslog is not supported for acct and packet event types.

fileCount

1-1024

Specifies the number of event log files that will be maintained for this event type. (default = 32).

fileSize

256-65535

Maximum size (in KB) that a single event log file will ever grow to. (default = 2048).

fileWriteMode

N/A

Event log NFS write mode. Options are:

  • default – Log data is written as a 1344-byte packet.
  • optimize – Log data is written as a 8000-byte packet. Optimize write mode results in IP fragmentation but yields better throughput.

filterLevel

N/A

Events that are at least as severe as the designated level will be logged. Options are:

  • critical – log only events of this threshold.
  • info – log every possible event.
  • major – log major and critical events only.
  • minor – log all events other than information.
  • noevents – do not log any events.
Note
The command to set the filterLevel for the acct event type is no longer applicable.

messageQueueSize

2-32

The number of event log message entries to buffer before writing to disk. (default = 10).

renameOpenFiles

N/A

Enable this flag to rename the most recent accounting file with “.ACT.OPEN” extension.

  • disabled (default)
  • enabled

rolloverAction

N/A

Event log rollover actions. Options are:

  • start – Start rollover action.
  • stop – Stop rollover action.

rolloverInterval

0-31536000

Event log rollover interval, in seconds.

rolloverStartTime

N/A

Specifies the start time for event log rollover. The format is CCYY-MM-DDTHH:MM:SS. For example: 2010-01-01T01:01:01

rolloverType

N/A

Event log rollover type. Options are:

  • nonrepetitive (default) – The rollover will occur once at the specified single instance.
  • repetitive – The rollover will occur repeatedly at the specified intervals.

saveTo

N/A

Use flag to specify that the events are saved to disk or not saved.

  • disk (default)
  • none

state

N/A

Specifies the requested state of the given Event Log type.

  • disabled – Logging is not activated.
  • enabled – (default) Logging is activated.
  • rollfile

 Accounting logs cannot be disabled.

syslogRemoteHost

0-255

The remote host where the messages are written to the syslog.

syslogRemotePort

1-65535

Specifies the port to use to send messages to the remote syslog. Default value is 514.

syslogRemoteProtocol

N/A

The protocol to use to send messages to the remote syslog. Options are:

  • relp
  • tcp (default)
  • udp

syslogState

N/A

Enable flag to log events of specified type to syslog.

  • disabled (default)
  • enabled
Multiexcerpt
MultiExcerptNametypeAdmin2
Caption
0Table
1Type Admin Event Log Parameters (request command)

Parameter

Length/Range

Description

typeAdmin

N/A

Event Log configuration table for configuration items related to each Event Log type.

<event_type>

N/A

Specifies the type of event log to roll over:

  • acct – System account data. These files have .ACT extensions.
  • audit – System audit data. These files contain a record of all management interactions that modify the state of the system. These files have .AUD extensions. It  includes   all the changes made via the CLI and the Netconf interface. (This attribute is only available to an Administrator)
  • debug – System debugging data. These files have .DBG extensions.
  • packet – Packet information details. These files have .PKT extensions. If enabled, stores the packet details to .PKT files.
  • security – Security level events. These files have .SEC extensions. (This attribute is only available to an Administrator)
  • system – System   level events. These files have .SYS extensions.
  • trace – System trace data. These files have .TRC extensions.

rolloverLogNow

N/A

This control is used with request command to perform a roll-over of the specified log immediately.

...

Code Block
languagenone
% set oam eventLog typeAdmin packetsystem fileCount 1 fileSize 256 rolloverInterval 2 state enabled syslogState disabled
% show oam eventLog typeAdmin packetsystem
   state enabled;
   fileCount 1;
   fileSize 256;
   rolloverInterval 2;
   syslogState disabled;

...

Code Block
languagenone
% request oam eventLog typeAdmin packetsystem rolloverLogNow

This example displays typeAdmin event log details. It has been shortened for brevity.

Code Block
languagenone
% show details oam eventLog typeAdmin

typeAdmin system {
    state                enabled;
    fileCount            32;
    fileSize             2048;
    messageQueueSize     10;
    saveTo               disk;
    filterLevel          major;
    rolloverInterval     0;
    rolloverType         nonrepetitive;
    rolloverAction       stop;
    fileWriteMode        default;
    syslogState          disabled;
    syslogRemoteHost     0.0.0.0;
    syslogRemoteProtocol tcp;
    syslogRemotePort     514;
    renameOpenFiles      disabled;
}
typeAdmin debug {
    state                enabled;
    fileCount            32;
    fileSize             2048;
    messageQueueSize     10;
    saveTo               disk;
    filterLevel          info;
    rolloverInterval     0;
    rolloverType         nonrepetitive;
    rolloverAction       stop;
    fileWriteMode        default;
    syslogState          disabled;
    syslogRemoteHost     0.0.0.0;
    syslogRemoteProtocol tcp;
    syslogRemotePort     514;
    renameOpenFiles      disabled;
}
typeAdmin trace {
    state                enabled;
    fileCount            32;
    fileSize             2048;
    messageQueueSize     10;
    saveTo               disk;
    filterLevel          info;
    rolloverInterval     0;
    rolloverType         nonrepetitive;
    rolloverAction       stop;
    fileWriteMode        default;
    syslogState          disabled;
    syslogRemoteHost     0.0.0.0;
    syslogRemoteProtocol tcp;
    syslogRemotePort     514;
    renameOpenFiles      disabled;
}
typeAdmin acct {
    state                enabled;
    fileCount            32;
    fileSize             2048;
    messageQueueSize     10;
    saveTo               disk;
    filterLevel          info;
    rolloverInterval     0;
    rolloverType         nonrepetitive;
    rolloverAction       stop;
    fileWriteMode        default;
    syslogState          disabled;
    syslogRemoteHost     0.0.0.0;
    syslogRemoteProtocol tcp;
    syslogRemotePort     514;
    renameOpenFiles      disabled;
}...
Noprint

Back To Top