Versions Compared

Old Version 4

changes.mady.by.user Ribbon Communications

Saved on

compared with

New Version 5

changes.mady.by.user Ribbon Communications

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

Additional section:

Children Display
styleh6

Panel

In this section:

Table of Contents
maxLevel2

Panel

...

borderColorgreen
bgColortransparent
borderWidth2

In this section:

Table of Contents
maxLevel2

Info
iconfalse

Related articles:

Children Display

 

This object contains information about each SIP-to-CPC Cause Mapping Profile on the node.

Info

Spacevars
0series4
 supports up to 64 SIP-to-CPC and 64 CPC-to-SIP cause code mapping profiles.

To View Cpc To Sip Cause Map Profile

On SBC main screen, go to Configuration > Profile Management > Category: Signaling Profiles >Sip Cause Code Mapping > Cpc To Sip Cause Map Profile.

The Cpc To Sip Cause Map Profile window is displayed.

Caption
0Figure
1Profile Management - Signaling Profiles - Cpc To Sip Cause Map Profile
 

 Image Modified

To Edit Cpc To Sip Cause Map Profile

To edit any of the Cpc To Sip Cause Map Profile in the list, click the radio button next to the specific Cpc To Sip Cause Map Profile name.

Caption
0Figure
1Profile Management - Signaling Profiles - Cpc To Sip Cause Map ProfileProfile Management - Signaling Profiles - Cpc To Sip Cause Map Profile Highlighted
 

 Image Modified

The Edit Selected Cpc To Sip Cause Map Profile window is displayed below.

Caption
0Figure
1Profile Management - Signaling Profiles - Cpc To Sip Cause Map Profile Edit Window
 

 Image Modified

Make the required changes and click Save at the right hand bottom of the panel to save the changes made.

To Create Cpc To Sip Cause Map Profile

To create a new Cpc To Sip Cause Map Profile, click New Cpc To Sip Cause Map Profile tab on the Cpc To Sip Cause Map Profile List panel.

Caption
0Figure
1Profile Management - Signaling Profiles - Cpc To Sip Cause Map Profile Fields
 

 Image Modified

The Create New Cpc To Sip Cause Map Profile window is displayed.

Caption
0Figure
1Profile Management - Signaling Profiles - Cpc To Sip Cause Map Profile Create Window
 

 Image Modified

The following fields are displayed:

Caption
0Table
1CPC To SIP Cause Map Profile Parameters
 

Parameter

Description

Name

The name of a SIP_TO_CPC CAUSE MAP PROFILE. This name cannot start with the string "default".

Base Profile

The name of one of the three fixed, default CAUSEMAP PROFILEs that the new CAUSEMAP PROFILE that is being created will be based upon. These CPC-to-SIP base profiles are:

  • DefaultCpcSip—current Sonus Mappings.
  • DefaultQ1912CpcSip—based on Q1912.5.
  • DefaultRFC3398CpcSip—based on RFC3398.
  • DefaultTS29163CpcSip—based on 3GPP TS 29.163

The base profiles cannot be modified. The base profile that you designate will be copied to the profile that you create. Additions, modifications, and deletions may subsequently be applied to the new profile via the CONFIGURE command.

Cause Map

Specifies the SIP-to-CPC cause mapping values. Enter cause map value between 1-255 and specify the following reasons:

  • q850Reason – Q.850 reason for a given CPC cause value. Specifies the Reason Header Q.850 value to include in the SIP message (when the includeQ850Reason parameter is enabled). Also indicates the cause code value to include in MIME encapsulated ISUP, if the call uses SIP-I signaling. (range: 0- 127 / default = 0).

    A value of "0" indicates that the Reason Header Q.850 value should be equal to the predefined ISUP mapping associated with the cpcCause value. If no predefined ISUP mapping exists (as for internal cause codes 151-159), the ISDN mapping is used.

  • sipCause – SIP Cause value for a given CPC cause value. (range: 300-606).

Note

This parameter applies to Cpc To Sip CauseMap Profile only.

Unrec Action

Specifies the SIP cause value to use when an unrecognized ISUP cause value is received (a value that is not present in the CPC_TO_SIP CAUSEPROFILE):

  • q1912Procedure—Use the default value of the ISUP class of the unrecognized cause code and map that value to the SIP cause value, the default in DefaultQ1912CpcSip.
  • rfc3398Procedure—Use SIP 500 message (SERVER INTERNAL ERROR), the default in DefaultRFC3398CpcSip.

Include Q850
Reason

Specifies whether SIP error messages associated with this profile will include a
Reason Header Q.850 value taken from the Q850REASON parameter.

  • enabled—SIP error messages associated with this profile will include a Reason. Header Q.850 value taken from the Q850REASON parameter.
  • disabled (default)—the SIP error messages will not include a Q850REASON value.

To Delete Cpc To Sip Cause Map Profile

To delete any of the created Cpc To Sip Cause Map Profile, click the radio button next to the specific Cpc To Sip Cause Map Profile which you want to delete.

Caption
0Figure
1Profile Management - Signaling Profiles - Cpc To Sip Cause Map Profile Highlighted
 

 Image Modified

Click Delete at the end of the highlighted row. A delete confirmation message appears seeking your decision.

Caption
0Figure
1Profile Management - Signaling Profiles - Cpc To Sip Cause Map Profile Delete Confirmation
 

 Image Modified

Click Yes to remove the specific Cpc To Sip Cause Map Profile from the list.

...

Pagebreak