Page History

...

Warning
Sonus-provided SFP modules must be used to guarantee proper operation of the external ports. Failure to follow this recommendation may cause permanent damage to the system.

...

1Gb SFP Parts

The following 1G 1Gb SFP transceivers are compatible with 

Spacevars
0 model5

in all Management, Media, and HA ports:

...

10Gb SFP Parts

Optionally, MEDIA0 can be used as a single 10G 10Gb port, with the remaining MEDIA ports empty. The parts for the 10G SFP 10Gb SFPs are:

...

Follow these steps to install SFPs for the first time. To replace an SFP, see the CRU document.:

1. Attach an Electrostatic Discharge (ESD) wrist strap (provided in the 

   Spacevars
   0 model5

   kit) using the ESD grounding point on the rear panel of the chassis (see Connecting ESD Wrist Strap). 
2. Insert the Sonus-approved SFP transceiver into the desired socket and ensure that the proper orientation when inserting, and that you will hear a "click-in " sound when the SFP is seated latched correctly.
3. Connect/reconnect the fiber optic and/or CAT 5 cables, as appropriate, to media and HA ports.
4. Verify LEDs above the part are flashing indicating that indicates link status and data activity.
5. Verify port functionality using the CLI show status system commands, once the SBC application software is installed and the system is up and running (for details, see show status system from the 5.0.x documentation).

   1. Verify management and packet port functionality:

      Code Block
      language none
      > show status system ethernetPort

   2. Verify HA port functionality:

      Code Block
      language none
      > show status system highAvailabilityPort

Note
If an unsupported SFP module is inserted, an error message similar to the following displays: PNPS: pkt1 SFP detected not supported by Sonus! Turning pkt1 off! PNPS: Replace pkt1 SFP with an approved Sonus part to ensure NEBS. Replace the SFP modules to resolve issue.

Connecting Serial Port

When For connecting a serial cable to the rear serial port of the 

Spacevars
0 model5

server for communication to communicate with a host PC, refer to the figure below for the serial port locationconnection image.

Caption
0 Figure 1 SBC Serial Port Connection

...

To establish the Management port connections, connect the CAT5e cable to the Mgmt 0Mgmt0, Mgmt 1Mgmt1, Mgmt 2Mgmt2, and Mgmt 3Mgmt3 ports. The CAT5e cable may be connected to a switch, router, LAN or WAN as per the customer requirements.

...

The physical connection between two 

Spacevars
0 model5

systems consists of a pair of GigE GIG-E cables (Use the Single mode or Multi mode fiber optic CAT5e cable (NON-CROSSOVER TYPE ONLY), directly connected between each HA ports.

The HA connections provides both box-Level and port-level redundancy system. The HA pair system consists of four management ports; two ports each per system. When a switchover occurs, the logical management address follows the currently active server. For the Media ports, the MAC and IP addresses float (are replicated from active to standby on failover switchover).

Caption
0 Figure 1 Management and HA Port Connections for SBC 5400

...

Note
The Alarm port is not supported by the  Spacevars 0 model5 application software in this release.

The 

Spacevars
0 model5

Alarm ports , allow you to sense (Alarm In) and issue (Alarm Out) external signal. The Alarm Port utilizes a HD15 pin connector and supports 4 output alarms and 2 input alarms. You must create the remainder of the cable, wiring the appropriate sensor or alarm leads to the screw terminator on the connector. 

Caption
0 Figure 1 SBC 5400 Series Alarm Ports

...