Page History

Panel
In this section: Table of Contents maxLevel 2

Warning
Sonus-provided SFP modules must be used to guarantee proper operation of the external ports. Failure to follow this recommendation may cause permanent damage to the system.

Tooltip
tip Use ESD protective device

Overview

The 

Spacevars
0 series

supports the following Small Form-factor Pluggable (SFP) transceivers in all Management, Media, and HA ports. The SFPs are Customer Replaceable Units (CRU).

Div
class pdf8pttext
Caption 0 Table 1 SFP Characteristics 3 SFP Characteristics Transceiver Type Product Code SFP Type Manufacturers  Part Number Wavelength  (nm) Tx Power (dBM) Rx Power (dBM) Description Multi-mode fiber SBC‐5XXXSFPMM 1G Ethernet MM AVAGO TECHNOLOGIES AFBR‐5715PZSN1, BROADCOM AFBR‐5715PZ‐SN1, FINISAR FTLF8519P2BNL‐SS, FINISAR FTLF8519P3BNL‐SS 850 -9.5 (Min) -3 (Max) -17 0 GIG-E, MULTI-MODE, FIBER OPTIC TRANSCEIVER MODULE, LC, SMALL FORM PLUGGABLE (SFP), 300M Single-mode fiber SBC‐5XXXSFPSM 1G Ethernet  SM AVAGO TECHNOLOGIES AFCT‐5715PZSN1, BROADCOM AFCT‐5715PZSN1, FINISAR FTLF1318P2BTL‐SS, FINISAR FTLF1318P3BTL‐SS 1310 -9.5 (Min) -3 (Max) -19 -3 GIG-E, SINGLE MODE, FIBER OPTIC TRANSCEIVER MODULE, LC, SMALL FORM PLUGGABLE (SFP), 10KM 1310NM, DMI Copper SBC-5XXX-SFPCOPPER 1G Ethernet Copper  AVAGO TECHNOLOGIES ABCU-5740RZ-SN1, BROADCOM ABCU-5740RZ-SN1, FINISAR FCLF8521P2BTL-SS NA NA NA NA NA GIG-E, 1000 BASE-T SMALL FORM PLUGGABLE (SFP)

Note
These numbers are taken from Vendor Datasheets.

 

To replace SFPs, use the procedure Replacing the SFP below.

Caption
0 Figure 1 SFP Ports

Parts and Tools Required

• Electrostatic discharge (ESD) strap
• Replacement SFP transceivers.

Include Page
ESD_wriststrap_5K ESD_wriststrap_5K

Anchor
ReplacingSFP ReplacingSFP

Replacing the SFP

Perform the following procedure to replace the SFP:

1. Attach an ESD wrist strap using the ESD grounding point on the rear panel of the chassis (see Connecting Electrostatic Discharge Wrist Strap for details).

2. Disconnect the fiber optic and/or Cat 5 cables, as appropriate, from media ports (Media 0-4) and HA ports (HA 0-1).

3. Disengage the SFP transceiver from

   Spacevars
   0 series

   . The method used to disengage the SFP transceiver will vary according to the manufacturer. For example, hold the wire latch and move it downwards to the horizontal position and pull it outwards, as shown below.

   Note
   The  Spacevars 0 product   Spacevars 0 5200 chassis contains four media ports and the Spacevars 0 product   Spacevars 0 5100 chassis two media ports.

   Caption
   0 Figure 1 Removing SFP

   Caption
   0 Figure 1 Inserting SFP

4. Insert the Sonus-approved SFP transceiver into the desired socket and ensure that the latch mechanism engages.

5. Reconnect the fiber optic and/or Cat 5 cables, as appropriate, to media and HA ports.
6. Verify LEDs above the part are flashing indicating link status and data activity.
7. Verify port functionality using the application.

CRU Storage

Tooltip
tip ESD protective device

All 

Spacevars
0 series

CRUs are shipped in electrostatic discharge bags and should be handled using appropriate ESD precautions.

The storage environment for these CRUs are:

• Humidity must be less than 95% (non-condensing).
• Temperature must be between -40C and +70C.

 

Include Page
ESD_footnote ESD_footnote

Pagebreak