Versions Compared

Old Version 10

changes.mady.by.user Ribbon Communications

Saved on

compared with

New Version 11

changes.mady.by.user Ribbon Communications

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

...

On the SBC main screen, go to Configuration > System Provisioning > Category: Trunk Provisioning > Trunk Group > Sip Trunk Group > Services > Nat NAT Traversal. The Nat NAT Traversal window is displayed.

Use the Nat NAT Traversal window to check NAT Traversal settings for each Address Context, Zone and Sip Trunk Group created, or for all Address Contexts, Zones and Sip Trunk Groups created. Use the drop-down boxes to select the desired Address Context, Zone and Sip Trunk Group. The Edit Nat Edit NAT Traversal window is displayed.

...

Caption
0Table
1Sip Trunk Group - Services - Nat Traversal parameters
 

Parameter

Description

Signaling NatNAT

Indicates whether or not NAT/NAPT support is required for signaling. 

  • disabled (default)
  • enabled

Include Page
No_NAT_for_IPv6
No_NAT_for_IPv6

Media NatNAT

Specifies the whether or not NAT/NAPT support is required for media. 
  • disabled (default) 
  • enabled
Panel
borderColor#fff2cc
bgColor#fffdf6

Note

Do not configure Media NatNAT and Ice Support flags flags on the same Trunk Group.

Include Page
No_NAT_for_IPv6
No_NAT_for_IPv6

Learn Nat NAT For Rtp Only

Enable flag to learn media NAT from the first RTP packet only. If disabled, media NAT is learned from any first packet received. For egress trunk groups, this flag is applicable only if Dynamic LRBT flag is disabled. If Dynamic LRBT is enabled, NAPT learning occurs on arrival of RTP packet until the call is connected, at which point point Learn Nat NAT For Rtp Only applies even even for egress Trunk Groups. The options are:

  • disabled (default) 

  • enabled

Panel
borderColor#fff2cc
bgColor#fffdf6

Note

The action of this flag does not apply to ICE Nat NAT traversal.

Ice Support

This parameter indicates the type of ICE method used for STUN packet check. The values are:

  • Ice Webrtc - This setting is used when inter-working with Webrtc Gateways, for example the Sonus WRTC Gateway or in situations when the SBC is presented with an ICE SDP from a WebRTC Enabled Endpoint.

    Panel
    borderColor#fff2cc
    bgColor#fffdf6

    Note

    When configured for this mode, SBC acts as a generic ICE-Lite agent.

  • Ice Lync - This is used when inter-working with a Microsoft Lync 2010 or 2013 client.
  • Ice Full - This is used when inter-working with a full ICE client which requires a STUN connectivity check to be generated by the SBC in response to its own STUN connectivity check.
Panel
borderColor#fff2cc
bgColor#fffdf6

Note

For MS Lync ICE (iceLync setting), keep-alive messages are sent only to RTP port.

Include Page
ICE_note
ICE_note

Panel
borderColor#fff2cc
bgColor#fffdf6

Note

The parameterparameter, Learn Nat NAT For Rtp Only, does not not apply to ICE and should not be enabled for the Trunk Group with ICE Support enabled.

Refer to SDP Support for a detailed description on Ice Support.

Ice Keepalive Timer

Specifies the keep alive timer in full-ICE and MS-Lync ICE. The value ranges from 0 to 60 seconds and the default value is 15 seconds.

Panel
borderColor#fff2cc
bgColor#fffdf6

Note

Ice Keepalive Timer appears only when Ice Support flag is set to Ice Full or Ice Lync.

Tcp TCP Keepalive Timer

Specifies the NAT keepalive timer This NAT TCP keep-alive timer sets the registration refresh rate (in seconds) for SIP over TCP. The value ranges from 15 to 65535 seconds and the default value is 240 seconds. (default = 240).

UDP Udp Keepalive Timer

Specifies the NAT keepalive timer This NAT UDP keep-alive timer sets the registration refresh rate (in seconds) for SIP over UDP. The value ranges from 15 to 65535 seconds and the default value is 60 seconds. (default = 60).

Outbound Tcp Keepalive Timer

Specifies the NAT outbound keepalive timer (in seconds) for SIP over TCP. The value ranges from 0 to 32767 and the default value is 240. 

Outbound Udp Keepalive Timer

Specifies the NAT outbound keepalive timer (in seconds) for SIP over UDP. The value ranges from 0 to 32767and the default value is 60. 

Secure Media Nat NAT Prefix

Use this parameter to match up to 'N' bits of the network IPv4 address obtained from signaling. If set to "0", feature is disabled, and no match of network IP address will occur.  The value ranges from 0 to 32 and the default value is 0.
Ice TCP Role

Use this flag to specify if SBC initiates the TCP connection for ICE Lync.The options are:

  • Passive (default): The SBC waits for the peer to initiate the TCP connection. Use this option when working directly with Lync endpoints.
  • Active:  Use this option for the SBC to initiate initiate the TCP connection when connected to internal-facing trunk groups where the peer is not behind the NAT. Also, use this option when working with certain Unified Communication (UC) servers such as Acano which expect the peer to initiate the TCP connection. This is only supported when there are no NATs between the SBC and the UC server.
Panel
borderColor#fff2cc
bgColor#fffdf6

Note

Ice TCP Role appears only when Ice Support flag is set to Ice Full or Ice Lync.

Refer to Configuring SBC and LYNC in Media Environment for configuration details.

...