| Parameter Name | Required | Service Affecting | Data Type | Default Value | Possible Values | Description |
|---|
| ConfigIEState | No | Yes | Enum | 1 | Possible values: - 0 - esDISABLED
- 1 - esENABLED
| Specifies the Administrative State of the resource. |
|---|
| ApplyToPortName | Yes | Yes | string | none | 128 - Max Length | Specifies which physical T1/E1 Port this signaling group is for. |
|---|
| Description | No | No | string | none | 64 - Max Length | Describes the Signaling Group so that it is easily identifiable when selected for a Call Route Table |
|---|
| IsdnSgSwitchVariant | Yes | Yes | Enum | 3 | Possible values: - 0 - isvATT4ESS
- 1 - isvATT5ESS
- 2 - isvDMS100
- 3 - isvNI2
- 4 - isvETSI
- 5 - isvQSIG
- 6 - isvINET1500
| Specifies the ISDN variant for this signaling group |
|---|
| IsdnSgSideOrientation | Yes | Yes | Enum | 0 | Possible values: - 0 - isoUser
- 1 - isoNetwork
- 2 - isoNone
| Specifies the ISDN user/network side for this signaling group |
|---|
| IsdnSgOverlapRxMode | Yes | Yes | Enum | 0 | Possible values: - 0 - iorDisable
- 1 - iorEnable
| Specifies if overlap receiving is enabled on the signaling group. Only valid for Euro ISDN (ETSI) and QSIG Switch Variants. |
|---|
| IsdnSgOverlapTxMode | Yes | Yes | Enum | 0 | Possible values: - 0 - iosDisable
- 1 - iosEnable
| Specifies if overlap sending is enabled on the signaling group. Only valid for Euro ISDN (ETSI) and QSIG Switch Variants. |
|---|
| IsdnSgIndicatedChannel | Yes | Yes | Enum | 1 | Possible values: - 0 - iicPreferred
- 1 - iicExclusive
| Specifies the setting of the Indicated Channel field for the Channel Identification IE in the SETUP message sent to the far end for this signaling group. |
|---|
| IsdnServiceMessageCapability | Yes | Yes | Enum | 1 | Possible values: - 0 - iscDisable
- 1 - iscEnable
| Specifies if service messaging is used on the signaling group. Only valid for ATT 4ESS, ATT 5ESS, NI2 and INS NET 1500 Switch Variants. |
|---|
| IsdnStopFarEndT310UponTryingFromSip | Yes | Yes | Enum | 0 | Possible values: - 0 - isfDisable
- 1 - isfEnable
| Specifies if a Q.931 PROGRESS message is sent to the far-end so that it does not timeout (T310) while SIP response is pending from the SIP leg, causing the call to release. This setting typically enabled only for testing scenarios and should not used in a production system. |
|---|
| IsdnAllowCallingNameDisplayToSwitch | Yes | Yes | Enum | 0 | Possible values: - 0 - iacDisable
- 1 - iacEnable
| Specifies if the Q.931 SETUP message is sent to the far-end should include the DISPLAY Information Element (IE). If this option is enabled, the DISPLAY IE is populated for NI2 or Euro-ISDN switch types, otherwise the DISPLAY IE is not populated for these switch types. | Info |
|---|
This setting is available when ISDN Side is set to User and Switch Variant is either NI2 or Euro-ISDN. |
| Info |
|---|
In general, the DISPLAY IE is populated according to ISDN communication standards. The NI2 and Euro-ISDN specifications state that the DISPLAY IE _should not_ be populated. This option allows you to override that configuration for your environment. |
|
|---|
| IsdnSgHuntMethod | Yes | Yes | Enum | 4 | Possible values: - 0 - sghmStandard
- 1 - sghmReverseStandard
- 2 - sghmRoundRobin
- 3 - sghmLeastIdle
- 4 - sghmMostIdle
- 5 - sghmOwnNumber
| Method that Call Control uses to allocate ISDN channels. This is only valid for Outbound or Bidirectional Direction settings. - Standard - This option assigns the first available low numbered channel.
- Reverse Standard - This option assigns the last available high numbered channel.
- Round Robin - This option assigns channels based on next available from low numbered to high numbered.
- Least Idle - This option chooses channels based on the least idle channel.
- Most Idle - This option chooses channels based on the most idle channel.
|
|---|
| IsdnSgDirection | Yes | Yes | Enum | 2 | Possible values: - 0 - sgdirInbound
- 1 - sgdirOutbound
- 2 - sgdirBidirectional
| Indicates the direction of calls supported - Inbound - Support only incoming calls from ISDN endpoints.
- Outbound - Support only outgoing call to ISDN endpoints.
- Bidirectional - Support both incoming or outgoing calls to ISDN endpoints.
|
|---|
| IsdnSgRingbackPlayPolicy | Yes | Yes | Enum | 0 | Possible values: - 0 - sgrbpAuto
- 1 - sgrbpAlways
- 2 - sgrbpNever
| Specifies when to generate local ring back - Auto - Depends if inband audio is available
- Always - always generate inband ringback
- Never - never generate inband ringback
|
|---|
| ToneTableNumber | Yes | Yes | int | 1 | Possible values: - 1 - Minimum
- 65534 - Maximum
| Specifies the Tone Table to use on this signaling group. This option is only available for Inbound and Bidirectional. |
|---|
| ActionsetTableNumber | No | No | int | 0 | Possible values: - 0 - Minimum
- 65534 - Maximum
| Specifies the Action Set Table to use on this signaling group. This option is only available for Inbound and Bidirectional. |
|---|
| RouteTableNumber | Yes | Yes | int | 1 | Possible values: - 1 - Minimum
- 65534 - Maximum
| Specifies the Call Route Table to use on the signaling group to route calls with. This option is only available for Inbound and Bidirectional. |
|---|
| NoChannelAvailableId | No | No | int | 34 | Possible values: | In case of "No Channel/Circuit available" release cause code, CCC is going to map this to the value configured against this entry in the signaling group. This cause code will be sent to the relevant protocol module. |
|---|
| TimerSanitySetup | No | No | int | 255000 | Possible values: - 180000 - Minimum
- 750000 - Maximum
| Specifies the sanity timer for setup message, in milliseconds. A Call that has not received a response from the peer switch will be released after this time. This is for all call types. The duration of this timer should be equal to or greater than the T301 timer. |
|---|
| IsdnSgTimerT301 | Yes | Yes | int | 180 | Possible values: | Specifies the timeout after the ISDN call enters Ringing before clearing the call if the call is not answered. The duration of this timer should not exceed the Call Setup Response Timer (TimerSanitySetup) |
|---|
| IsdnSgTimerT302 | Yes | Yes | int | 15 | Possible values: | Specifies the inter digit timeout before proceeding with the call in overlapped dialing |
|---|
| IsdnSgTimerT303 | Yes | Yes | int | 4 | Possible values: | Specifies the timeout after a SETUP is sent to wait for a proceeding response |
|---|
| IsdnSgTimerT305 | Yes | Yes | int | 30 | Possible values: | Specifies the timeout after a DISCONNECT is sent to wait for a response |
|---|
| IsdnSgTimerT308 | Yes | Yes | int | 4 | Possible values: | Specifies the timeout after a RELEASE is sent to wait for a response |
|---|
| IsdnSgTimerT309 | Yes | Yes | int | 6 | Possible values: | Specifies the timeout after the D channel goes down to release active calls |
|---|
| IsdnSgTimerT310 | Yes | Yes | int | 30 | Possible values: | Specifies the timeout after CALL PROCEEDING to wait for a call progress response |
|---|
| IsdnSgTimerT313 | Yes | Yes | int | 4 | Possible values: | Specifies the timeout for Network side ISDN after sending a CONNECT to wait for the response |
|---|
| IsdnSgTimerT314 | Yes | Yes | int | 4 | Possible values: | Specifies the timeout for QSIG to wait between SEGMENT messages for a segmented message |
|---|
| IsdnSgTimerT316 | Yes | Yes | int | 120 | Possible values: | Specifies the timeout after sending a RESTART message for a response |
|---|
| IsdnSgTimerT322 | Yes | Yes | int | 4 | Possible values: | Specifies the timeout after sending a STATUS ENQUIRY to wait for a response |
|---|
| IsdnSgTimerT3M1 | Yes | Yes | int | 120 | Possible values: | Specifies the timeout after sending a SERVICE for a response |
|---|
| ProtocolIdentifier | No | No | Enum | 1 | Possible values: - 0 - apiNetworkExtensions
- 1 - apiROSE
| Specifies the Protocol Identifier to use within ASN.1 for QSIG. |
|---|
| AsnNumberingSpace | No | No | Enum | 0 | Possible values: - 0 - ansLocal
- 1 - ansGlobal
| Specifies the ASN.1 numbering space for QSIG. |
|---|
| IncludeNFEIAPDU | No | No | Enum | 1 | Possible values: | Specifies whether or not to include the Network Facility Extension and Interpretation APDU in ASN.1 for QSIG. |
|---|
| IncludeInterfaceIdentifier | No | No | Enum | 0 | Possible values: | Specifies whether or not to include the interface identifier in out going channel identification information elements. |
|---|
| ChannelNumberBit | No | No | Enum | 1 | Possible values: | Specifies whether or not to set the high bit in the channel number byte in channel identification information elements. |
|---|
| SendRNInFacility | No | No | Enum | 0 | Possible values: | Controls how the redirecting number is sent for Euro ISDN (ETSI). When enabled, redirecting number is passed into the Facility IE. |
|---|
| PortChannelCountFull | Yes | Yes | Enum | 1 | Possible values: | Specifies whether or not every channel is being used for the signaling group. When set to 1 ApplyToChannelList is not used. Only applicable for PRI signaling groups. |
|---|
| ApplyToChannelList | Yes | Yes | string | none | 512 - Max Length | Apply to Channel List used to store the channel list from user. Comma seperated values of type "card.port:channel" E.g. 1.1:1,1.1:2,1.1:3,... if Channels selected and NULL, if no channels are selected. Only applicable for PRI signaling groups. |
|---|
| DelayChannelClearing | Yes | Yes | Enum | 0 | Possible values: | Specifies whether or not a channel should be kept open post Disconnect, when PI=8 received. |
|---|
| ChannelClearingDelay | Yes | Yes | int | 10 | | Delay in Seconds channel is kept open after receiving the DISCONNECT with PI=8. |
|---|
| TEIAssignment | No | Yes | int | -1 | Possible values: | Specifies the TEI to use for TE/User side BRI. 0 through 63 are absolute values and -1 is automatic assignment. If signaling group is set for PRI or NT/Network side BRI this is not used. |
|---|
| SGType | Yes | Yes | Enum | 0 | Possible values: - 0 - dstDS1
- 1 - dstBRI
- 2 - dstNone
| Specifies the type of ISDN signaling group. |
|---|
| SendFacilityPassthrough | No | No | Enum | 1 | Possible values: | Specifies if the Signaling Group should transmit a Facility message passed through from another ISDN Signaling Group. If set then Facility message is sent, if not set then the Facility message is dropped. |
|---|
| AddSetupProgress | No | No | Enum | 0 | Possible values: - 0 - apiNone
- 1 - apiNotEndToEnd
- 2 - apiDestISDN
- 3 - apiOrigISDN
- 4 - apiReturnISDN
- 5 - apiInterworking
- 6 - apiInbandInfo
- 7 - apiDelayEncountered
| Specifies if an outgoing SETUP message should have a Progress Indicator IE added to it with the configured value. Only adds the IE if one is not already present. |
|---|
| AddNetworkSpecificFacility | No | No | Enum | 0 | Possible values: | Specifies if an outgoing SETUP message should have a Network Specific Facility IE added to it. Only adds the IE if one is not already present. Only valid for ATT 4ESS and ATT 5ESS ISDN variants. |
|---|
| NSFIdentification | No | No | Enum | 0 | Possible values: - 0 - nidNone
- 1 - nidUser
- 2 - nidNational
- 3 - nidInternational
| Sets the Network Specific Facility IE identification if the IE is not present but does not modify an existing IE. Only valid when AddNetworkSpecificFacility is Enabled. |
|---|
| NSFInformation | No | No | Enum | 0 | Possible values: - 0 - ninSDN
- 1 - ninTollFree
- 2 - ninMEGACOM
- 3 - ninACCUNET
- 4 - ninInternationalTollFree
- 5 - ninMultiQuest
- 6 - ninLongDistance
- 7 - ninCallRedirection
| Sets the Network Specific Facility IE information if the IE is not present but does not modify an existing IE. Only valid when AddNetworkSpecificFacility is Enabled. |
|---|