Versions Compared

Old Version 3

changes.mady.by.user Ribbon Communications

Saved on

compared with

New Version 4

changes.mady.by.user Ribbon Communications

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

Add_workflow_for_techpubs
AUTH1UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26ccb8089c, userName='null'}
JIRAIDAUTHSYM-20961
REV5UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26ccb8089c, userName='null'}
REV6UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26ccb8089c, userName='null'}
REV3UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26cc1e0755, userName='null'}
REV1UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26ce5f0b8d, userName='null'}

Feature Overview

This feature extends the number of T1/E1 spans supported by SBC 1000 from 2 to 4 spans with the addition of a second T1/E1 line card. Previously the SBC 1000 supported one 2-port T1/E1 line card with the first T1/E1 port being licensed by default and the second port controlled by a software license. In this release, the first port is licensed by default, and the next three ports are configurable through software licensing.

...

Configuration and WebUI Changes

The Inventory Report tab shows the new Telco Module 8 in the location column.

Caption
0Figure
1Inventory Report
3Inventory Report
Image Removed

Access the Inventory Report (System > Inventory Report) to view the modules.

System Overview

The SBC 1000 Overview tab (System > Overview) shows the status of the 2-port DS1 line card in the front slot (Module 8).  Caption0
Figure1SBC 1000 Overview Module Status3SBC 1000 Overview Module Status

Image Removed

 

Port View

 SBC 1000 Ports view (Settings > Node Interfaces > Ports) shows the new DS1 port 8:1 and 8:2 along with configured port type, port status and port counters. Caption

0Figure
1SBC 1000 System Port View
3SBC 1000 System Port View

Image Removed

Configuration

Although there are no new configurable items added to SBC 1000 as a result of this feature, the existing applicable configuration elements are extended to include Port Configuration for module 8.

The SBC 1000 Set DS1 Port Type window of the Web UI (Settings > Node Interfaces > Ports>) window is modified to include module 8 as shown below. This window is used to set the port type of module 8 to T1 or E1 for both ports.    Caption

0Figure
1DS1 Port Type
3DS1 Port Type
Image Removed

Relay Configuration

 

The DS1 Relay Configuration object (Settings> Node Interfaces > Ports > Relay Config) allows the user to choose a relay configuration state on modules 7 and 8 of Online, Passthrough or Poweredown Passthrough. The SBC 1000 does not support choosing different settings between the two modules. Caption

0Figure
1Relay Configuration
3Relay Configuration
Image Removed

Limitations

  • Support for four DS1 ports will be available only on the SBC 1000 chassis running firmware release 6.1.0 or higher.
  • SBC 1000 does not do companding law conversion if the ports on one line card is configure as E1 and on the other as T1.
    • The companding law set in the system branch of the Web UI is applied to all the TDM ports in the system.
  • A software license is required for each port of the DS1 line card in the front slot (slot 8) of the SBC 1000 chassis.
  • Certain SKUs like SBC-1K-R-4P-FXSFXO-E may not able to support full call capacity if CAS is used on T1/E1 interfaces or silence based disconnect is enabled on the FXO ports.

...