Versions Compared

Old Version 14

changes.mady.by.user Ribbon Communications

Saved on

compared with

New Version 15

changes.mady.by.user Ribbon Communications

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Comment: updated SIP JIP for SBX-69416

Add_workflow_for_techpubs
AUTH1eyoustra
REV5bscoggins
REV6bscoggins
REV3snagaraju
REV1pbala

 

Include Page
Transparency_Profile_Note
Transparency_Profile_Note

Use this object to specify parameters associated with various enhanced services and features for this SIP trunk group.

To View and Edit Services

On the SBC main screen, go to Configuration > System Provisioning > Category: Trunk Provisioning > Trunk Group > Sip Trunk Group > Services.

The Services window is displayed. Use the drop-down boxes to select the desired Address Context, Zone and SIP Trunk Group. The Edit Services window is displayed.

Caption
0Figure
1SIP Trunk Group - Services
 

The following fields are displayed:

Caption
0Table
1SIP Trunk Group - Services
 

Parameter

Description

DNS Support Type

Indicates whether to use the DNS server for just A-record lookups, or for full NAPTR/SRV/A lookup as specified in RFC3263.

  • A-only
  • A-srv-naptr

Preconditions

 Indicates level of preconditions support for incoming (only) requests. For precondition support of outgoing requests, see Transmit Preconditions below.
  • None – (default)
  • Required
  • Supported
  • Transparent

Multiexcerpt include
MultiExcerptNamepreconditions Notes
PageWithExcerptReserving Network Resources

Transmit Preconditions

Specifies the level of preconditions support for outgoing requests/responses.
  • None – When set to "none",  SBC does not add SIP precondition attributes in SDP of outgoing request even if attributes are present in the SDP of incoming requests.
  • Required – Use this option to add SIP precondition attributes in SDP of outgoing request even if attributes are NOT present in the SDP of incoming requests. If precondition attributes are added by SBC, the local preconditions are set to ‘met’ and remote preconditions are set to ‘not-met’.
  • Supported – (default) Use this option to ensure backward compatibility behavior. Use this option to add SIP precondition attributes in SDP of outgoing request only if attributes are present in the incoming request.

Precondition Intwk Using183

(This flag is for specific call flows and is not intended for generic use)

Enable this flag to locally generate first 183 responses for preconditions interworking before egressing INVITE. If disabled, these responses are dropped.

  • Disabled (default)
  • Enabled

Note: Do not enable Precondition Intwk Using183 when End-to-End Prack is configured.

Multiexcerpt include
MultiExcerptNamepreconditionIntwkUsing183 Notes
PageWithExcerptReserving Network Resources

Honor Sdp Clock Rate

Enable this flag to allow the mapping of up to five DTMF Payload Types (PT), each with a different clock rate of a preferred or selected payload type for audio.

If the flag is disabled, all DTMF PTs except 8 kHz (both send and receive) are dropped.

  • Disabled (default)
  • Enabled

Sip Ars Profile

Specifies the name of the SIP ARS (Address Reachability Service) profile.

Disconnect Treatment Profile

Specifies the name of the Disconnect Treatment Profile.

Emergency Call Profile

Specifies the name of the Emergency Call Profile.
Hplmn ProfileSpecifies the name of an HPLMN Profile to use in handling emergency calls from outbound roaming users when S8 Home Routing (S8HR) is in use. Refer to Emergency Call Handling for the Roaming Users in S8HR Model.
Vplmn ProfileSpecifies the name of a VPLMN Profile to use in handling emergency calls from outbound roaming users when S8 Home Routing (S8HR) is in use. Refer to Emergency Call Handling for the Roaming Users in S8HR Model.

Sip Security Profile

Specifies the name of the SIP Security Profile.
Dynamic Blacklist ProfileSpecifies the name of the Dynamic Blacklist Profile.

Emergency Call Handling Mode

Use this parameter to specify how to handle emergency calls.

Note: To use any of the first three options, Use Psx Route For Emergency Call must also be enabled.

  • Emergency Reg Required – Use this option to reject the emergency session establishment without an emergency registration.

  • Emergency Reg Supported – Use this option when emergency registrations are supported, but emergency session establishment is possible without an emergency registration.

  • None (default) – Use this option when not using emergency registrations to perform PSX dip for registered user for emergency calls.

  • Reject With 380 – Use this option to reject an INVITE request with ‘380 Alternate Service’ response code from Ingress leg when the request is identified as emergency request and redirection flag is set to redirection mode.

See Emergency Registration for emergency registration functionality.

JSRC Bandwidth Reservation

If disabled at the global level, the Trunk Group configuration will not be applied. The options are:

  • Disabled (default)
  • Enabled

Remote EPreservation

If disabled at the global level, the Trunk Group configuration will not be applied. The options are:

  • Disabled (default)
  • Enabled

SIP JIP Profile

Specifies the name of the SIP JIP Profile. defaultJipProfile is the name of the default SIP JIP profile assigned to SIP trunk groups. You can select the name of a custom profile you created. Refer to Service Profiles - SIP JIP Profile.

Note: This parameter is only supported when the SBC is configured to use an external PSX.

SIP Jurisdiction Support

Enable this flag to allow insertion of JIP parameter in SIP trunk group ingress and egress headerssending JIP information in SIP-SIP, SIP-SIP-I and SIP-I to SIP scenarios.

  • Disabled (default)
  • Enabled
Note: This parameter is only supported when the SBC is configured to use an external PSX.
Transparency ProfileSpecifies the name of the Transparency Profile to associate with this SIP Trunk Group.
SIP Rec Metadata ProfileSpecifies the name of a SIP Rec Metadata Profile to associate with the SIP Trunk Group. This type of profile should be assigned to the SIP Trunk Group for the SIP Session Recording Server. Refer to Services - SIP Rec Metadata Profile for more information.
SIP Param Filter ProfileSpecifies the name of the SIP Param Filter Profile (SPF). The SPF defines the Allowed, Supported and Required headers parameter is filter/passed.
Use Previous Learned IP Address

Enable this option to latch on Previous Learned IP Address before performing SRV DNS Lookups, while sending mid-dialog SIP requests.

  • Disabled (default)
  • Enabled
Hpc Call Profile

Specifies the name (1-23 characters) of the HPC Call Profile. The possible states are:

  • Disabled (default)
  • Enabled
Dialog Event Notification Supported

Use this flag to support notification for a SUBSCRIBE with dialog event in this Trunk Group.

  • Disabled (default)
  • Enabled

Include Page
PSX only
PSX only

Colocated Pand Ecscf

Use this flag to support co-locating P-CSCF and E-CSCF on the ingress Trunk Group.

  • Disabled (default)
  • Enabled

 

Include Page
PSX only
PSX only

Test Call Number Profile

The name (1-23 characters) of the Test Call Number Profile.

The

Spacevars
0product
 uses the Test Call Number Profile to verify PSX test data access. The
Spacevars
0product
 uses this profile to determine whether to send a PSX query to a test PSX or to the production PSX. When the
Spacevars
0product
 receives a call from one of the configured numbers in the Test Call Number Profile, the
Spacevars
0product
 sends the PSX query to the test PSX, if available. When the 
Spacevars
0product
 receives a call from a number not included in the Test Call Number Profile, the
Spacevars
0product
 sends the PSX query to the production PSX.

Privacy ProfileSelect the name of Privacy Profile to apply to the SIP trunk group. Refer to Services - Privacy Profile for information.

Make the required changes and click Save.

 

Additional topics:

Div
stylepadding-left:1%;
idindent

Children Display
depth2
styleh5

 

Pagebreak