Versions Compared

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

 

Panel

In this section:

Table of Contents
maxLevel3

 

Include Page
Transparency_Profile_Note
Transparency_Profile_Note

This object specifies the values associated with the flags of Egress IP Attributes.

To View and Edit Flags

On SBC main screen, go to Configuration > System Provisioning > Category: Trunk Provisioning > Ip Signaling Profile > Egress Ip Attributes > Flags. The Flags window is displayed.

DEFAULT_H323

On the Flags window, choose the Ip Signaling Profile as DEFAULT_H323 to view the Flags for H323 Trunk Group.

Caption
0Figure
1Trunk Provisioning - Egress Ip Attributes H323 Flags
 

The following fields are displayed:

Caption
0Table
1Egress IP Attributes - Flags Parameters
 

Parameter

Description

Delay Cut Through

Specifies whether to enable the Delay Cut Through flag or not. The options are:

  • Disable
  • Enable

Dont Send Fast Start Proposal

Specifies whether to send the fast start proposal or not. The options are:

  • Disable
  • Enable

Insert In Band Indication

Specifies whether to enable the Insert In Band Indications flag or not. The options are:

  • Disable
  • Enable

Wait Till Connect Before Abandon Fast Start

Specifies whether to wait to connect before the abandon fast start or not. The options are:

  • Disable
  • Enable

Qos Based Routing

Specifies whether to enable the Qos based Routing or not. The options are:

  • Disable
  • Enable

DEFAULT_SIP

On the Flags window, choose the Ip Signaling Profile as DEFAULT_SIP to view the Flags for SIP Trunk Group.

Caption
0Figure
1Trunk Provisioning - Egress Ip Attributes SIP Flags
 

The following fields are displayed:

Caption
0Table
1Egress Ip Attributes SIP Flags Parameters
 

Parameter

Description

Bgcf Target Scheme Transparency

When enabled, the

Spacevars
0series
preserves the scheme used by the SIP INVITE Request-URI when the INVITE is routed by the
Spacevars
0series
, acting as a BGCF supporting Tel-URL. When disabled, the
Spacevars
0series
changes the scheme used by the Request-URI parameter to SIP in the egress INVITE message (this is the default).

The options are:

  • Enable
  • Disable (default)
Convert Inactive To Sendrecv

This flag is used by the

Spacevars
0series
to control the a-line in the SDP of an egress SIP INVITE message. When enabled, the
Spacevars
0series
converts a=inactive to a=sendrecv in the egress INVITE message. When disabled, the
Spacevars
0series
continues to use a=inactive, when appropriate, in the egress INVITE message.

The options are:

  • Enable
  • Disable (default) 
Note
iconfalse
titleNote

If 'onhold' is received on ingress leg and ‘sendrecv’ is sent to egress leg, then the peer egress must respond with 18x/2xx with ‘sendrecv’. Only the ingress leg can trigger ‘offhold’. Other behavior is not supported.


Disable 2806 ComplianceDisable2806Compliance

If enabled, the 2806 Compliance Code is disabled, and no phone context or user=phone parameters are signaled in egress messages.

The options are:

  • Enable Disable (default) 
  • EnableDisable
Disable Optional Register Parameters

Controls whether the

Spacevars
0series
sends the DTG (Destination Trunk Group) parameter in the Contact header  of egress REGISTER messages. When enabled, the
Spacevars
0series
does not send the DTG parameter. When disabled, the
Spacevars
0series
sends the DTG parameter.

The options are:

  • Enable
  • Disable (default) 
Map181Or182Message To 183

This parameter is used by the

Spacevars
0series
to control SIP response processing. When enabled, the
Spacevars
0series
maps 181 or 182 response messages to 183. When disabled, the
Spacevars
0series
handles 1xx response messages normally.

The options are:

  • Enable
  • Disable (default) 
Map Contractor Number In PSig Info Header

When enabled, the Contractor Number parameter will be mapped into the outgoing SIP P-Sig-Info header. The P-Sig-Info header is a customer-specific SIP header used to convey ISUP information in SIP messages.

The options are:

  • Enable
  • Disable (default) 
Same call Id For Required Authorization

Enable this flag to support sending an INVITE with credentials on receiving a 401 (Unauthorized) or 407 (Proxy Authentication Required) response to initial INVITE with the same call ID as in the original INVITE. 

The options are:

  • Enable
  • Disable (default) 
Note
iconfalse
titleNote

To view and configure this flag, you must first enable both 'Auth Code Headers' transparency flag and 'Status Code 4xx6xx' relay flag.


Suppress Unregister

When enabled, the

Spacevars
0series
does not send an unregister message (Register=0) to the registrar upon expiration of a SIP UA registration. When deselected (default), the
Spacevars
0series
generates unregister messages on the egress leg if the UA does not refresh the registration on time.

The options are:

  • Enable
  • Disable (default) 
Ttc Isup Mapping

When enabled, and when the IP protocol type of the IP signaling profile entry is SIP or SIP-I, the application that receives the

Spacevars
0series
policy response (which can be either the SIP signaling gateway application on the
Spacevars
0series
or the SIP core proxy on the
Spacevars
0series
) applies the mapping necessary for TTC-ISUP signaling.

The options are:

  • Enable
  • Disable (default) 
Use Called Party In Request Uri

When enabled, the

Spacevars
0series
copies the username that has been selected for the "To" header to the Request URI instead of the registered username. When disabled, the
Spacevars
0series
includes the registered username in the Request URI. This flag is used by the
Spacevars
0series
when interoperating with IP-PBXs that require the real end station number in the Request URI in order to do proper routing of calls terminating on them.

The options are:

  • Enable
  • Disable (default) 
Use Colon In Sdp Media Type Parameter

When enabled, a colon ":"  is used as the separator between the SDP Media Type parameter key and value. When disabled, an equal sign (=) is used as the separator between the SDP Media Type parameter key and value.

The options are:

  • Enable
  • Disable (default) 
Validate Isub Address

When enabled, the

Spacevars
0series
validates ISUB digits for called and calling parties. When disabled, the
Spacevars
0series
will not validate ISUB digits.

The options are:

  • Enable
  • Disable (default) 
Qos Based Routing

Specifies whether to enable Qos Based Routing or not.

The options are:

  • Enable
  • Disable (default)
Ignore SDP After Offer Answer Completed

If enabled, SBC ignores the new SDP at egress leg in subsequent 1xx-rel or final 200 OK after Offer Answer for the initial Invite dialog have been completed and would not trigger a new offer or answer.

The options are:

  • Enable
  • Disable (default)
Include Enum Parameters

If enabled, SBC sends ENUM parameters in the outgoing INVITE. If disabled, SBC drops ENUM parameters received from ENUM server.

The options are:

  • Enable
  • Disable (default)
Note
iconfalse
titleNote

If Include Enum Parameters flag is enabled, other flags for standard parameters such as cic, npdi should not be configured.

Make the required changes and click Save at the right hand bottom of the panel to save the changes made.