Page History

Enable flag to send additional CDR information within Sonus vendor-specific Attribute Value Pairs (AVPs) in Accounting-Request (ACR) messages over the existing Rf Interface.

• disabled (default)
• enabled

Use this flag to enable the Rf Accounting application at the system level to send accounting information over Rf Interface. See Rf Interface for feature details.

• disabled (default)
• enabled

Enable flag to prevent failed call ACR event from being sent.

• disabled (default)
• enabled

Use this parameter to specify the interim account interval value to send when no interval is received in ACA. Set value to “0” to not send interim record (default = 30).

congRelDelay

N/A

Amount of time (in seconds) that a call which is rejected due to congestion will be delayed before the release is issued. (default = 0).

displaylevel

1-64

To display different levels of output information in show commands.

establish

N/A

The Gateway Signal Channel Establishment Timer (in seconds.) This value applies to all signal channels. (default = 10).

idle

N/A

Amount of time (in hours) a GW Signaling Link May be idle before it is taken down. (default = 0).

keepalive

N/A

The Gateway Signal Channel Keep-alive Timer (in seconds.) This value applies to all signal channels. (default = 3).

retry

N/A

Amount of time (in minutes) the SBC will continue to attempt to recover a GW Signaling Link as long as there are stable calls up. (default = 60).

displaylevel

1-64

To display different levels of output information in show commands.

establish

0-127

The H225 signal channel establishment timer (in seconds). Default value is 4.

t301

0-65535

The T301 call timer (in seconds). Default value is 180 seconds.

t302

0-127

The T302 call timer (in seconds). Default value is 15 seconds.

t303

0-127

The T303 call timer (in seconds). Default value is 4 seconds.

t304

0-127

The T304 call timer (in seconds). Default value is 20 seconds.

t310

0-127

The T310 call timer (in seconds). Default value is 10 seconds.

tcpConnect

0-127

The TCP connect timer (in seconds). Default value is 3 seconds.

discardPeriod

1-10

Discard period (in seconds) for the Peer Overload back-off algorithm. (default = 2).

rejectThreshold

0-50

Specifies the reject threshold (in rejects/sec) for the Peer Overload backoff algorithm. (default = 1).

samplingPeriod

1-10

Specifies the sampling period (in seconds) for the Peer Overload back-off algorithm. (default = 2).

stepDownGain

1-200

Specifies the step down gain for the Peer Overload back-off algorithm. (default = 100).

displaylevel

1-64

To display different levels of output information in show commands.

egressRNParam

N/A

The egress RN parameter. Specifies whether the 

• disabled
• enabled (default)

loopDetectionFeature

N/A

When enabled, the SIP Stack performs loop detection on incoming INVITE messages.

• disabled – The SIP signaling group processes the INVITE message.
• enabled (default)

maxPduSizeValue

N/A

The maximum PDU size recognized by the

• pdusize2kb – 2,048 bytes
• pdusize3kb – 3,072 bytes
• pdusize6kb – 6,000 bytes
• pdusize15kb (default) – 15,000 bytes
• pdusize32kb – 32,000 bytes
• pdusize60kb – 60,000 bytes

multipleContactsPerAor

N/A

This flag enables support of multiple contacts per Address Of Record (AoR).

• disabled – SBC maintains a single RCB per Address of Record (AoR). Any existing binding information is overwritten on receipt of REGISTER from a new contact for the same AoR.
• enabled (default) – SBC maintains different RCBs for each new registration. A registration is considered new when the source IP port of the REGISTER request is different from earlier registration for the same AoR. If a registered UE initiates a communication on behalf of the AoR, SBC fetches the corresponding RCB based on source IP port of the UE.

 See Multiple Contacts per AoR for additional details.

registrarSupportContactParam

N/A

Enable flag to support parameters in the Contact header:

• disabled – Parameters in the Contact header are not supported. This value is provided only for backwards compatibility.
• enabled (default) – Parameters in the Contact header are supported.

suppressErrorInfoHdr

N/A

Enable flag to suppress Error-Info header in a response to a request message with syntax error.

• disabled (default) – SBC includes Error-info header in the response.
• enabled –  SBC does not include Error-Info header in an error status. 

Use this parameter to specify the time gap, in milliseconds, between a final response of surrogate register and the next surrogate register message sent across all peers. (default = 0, disabled)

If surrogate registration is active and you wish to disable pacing, first disable surrogate registration for all Peers using following command syntax:

% set addressContext <AC name> zone <zone name> ipPeer <peer name> surrogateRegistration state disabled

ucidNodeId

1-32767

UCID Node Id used to generate the UCID in the User-to-User Header. (default = 0)

stnSr

1-32 characters

Request URI for a transfer call sent by MSC on PS to CS call hand-off.