Versions Compared

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

Anchor
BackToTop
BackToTop

Noprint

 

...

Include Page
IP_for_MGMT_and_Media_on_diff_subnets
IP_for_MGMT_and_Media_on_diff_subnets

 Click

Click here

...

to download sample spreadsheet.


SBC SWe System Information

Description

Example/Recommendation
SBC System Name

This is the name of the overall SBC system, and is used as the designation of all servers within HA pair. See System Name and Hostname Conventions for naming conventions.

If external routing is used, the system name is referred to by the PSX.

You MUST use the same name on the Active and Standby system installation.

DALVSBC01
Local Host/Node name (ceName)

Name of the primary server. Typical naming convention is "<system name>a".

A best practice is to include the "a" suffix even for stand-alone systems to facilitate easy upgrade to HA in the future.

DALVSBC01a
Peer Host/Node name (ceName)

(HA only) Name of the secondary server. Typical naming convention is "<system name>b".

DALVSBC01b, or none
Server RoleSpecifies the role of the SBC VM.

Active/Standby

Time zone

The time zone used in your billing records. Can be the time zone of the location of the SBC system.

Note
Changing the time zone will cause the application to restart.
gmtMinus06-Central- US
SBC SWe System ContactContact name and phone number to use for physical support.

Joe Smith 888-555-1212

SBC SWe System LocationPhysical location of the system.Dallas, TX
NTP Primary IP AddressThe primary IPv4 or IPv6 address of the NTP server. A NTP source is necessary for correct system operation.10.11.12.2/24
or
fd00:10:6b50:4130:1
NTP Secondary IP AddressThe optional secondary IPv4 or IPv6 address of the NTP server.10.11.12.3/24
or
fd00:10:6b50:4130:2
TIPC NETID

Specifies unique Transparent Inter-process Communication (TIPC) network communications protocol network identity. This network identity must be same in both active and standby VMs for inter-process communication.

Recommendation is to use default value when configured for single HA pair on HA subnet (subnet for HA ports of active/standby).

Note
TIPC NETID must be unique for a given HA pair in any given cluster.
1500 (default)
Logical Management IP Address

This IP address can be used to access the active unit, it is not tied to a particular physical unit. When a unit becomes active, this IP address “moves” to that unit.

Logical management IP address should be from same subnet as the physical management IPs. 

10.11.13.3 (or any IP address within the Management IP subnet)
Logical Management IP Address NameThe name of the Logical Management IP (used for reference purposes only).DALNBS01_MGMT


Unit A and Unit B Information


Configure these details on Unit A only (IP address information moves from Unit A to B on a fail-over)

Packet Ports
Packet Port 0 IP Address

The IP address of the pkt0 interface. SIP and RTP traffic use this physical interface. This IP address is used for RTP traffic (SIP traffic uses a different IP address).

10.11.14.1
Packet Port 0 VLANThe VLAN tag of the pkt0 interface (optional).100
Packet Port 0 NetmaskThe Netmask of the pkt0 interface (in “prefix” format)./24
Packet Port 1 IP AddressThe IP address of the pkt1 interface. SIP and RTP traffic use this physical interface. This IP address is used for RTP traffic (SIP traffic uses a different IP address).10.11.15.1
Packet Port 1 VLANThe VLAN tag of the pkt1 interface (optional).200
Packet Port 1 NetmaskThe Netmask of the pkt1 interface (in “prefix” format)./24

HA Ports (not applicable for stand-alone configuration)

Info

The HA ports of active and standby SBC nodes should be on the same subnet when the boxes are not directly connected.

Active CE IP

Specifies the active VM IP address in HA pair. The Active CE uses this IP which is configured to the HA port to communicate/synchronize/mirror the data with the Standby CE.

These Inter CE IP addresses should be in a different network from the management network.

Recommendation is to use default value when configured for single HA pair on HA subnet (subnet for HA ports of active/standby).

169.254.99.1 (default)

Note

Active and Standby CE IP addresses must be in the same subnet.

Standby CE IP

Specifies the standby VM IP address in HA pair. The Standby CE uses this IP which is configured to the HA port to communicate/synchronize/mirror the data with the Active CE.

These Inter CE IP addresses should be in a different network from the management network.

Recommendation is to use default value when configured for single HA pair on HA subnet (subnet for HA ports of active/standby).

169.254.88.1 (default)
HA Interface Mask (Inter CE Prefix)

Netmask of the network in which the Active/Standby IPs are configured.

Note

If default Active and Standby CE IP addresses are not used, use Inter CE prefix as '255.255.255.0'.

255.255.0.0 (default)
Management Ports
Info

The configuration of the IP management interface is performed as part of the initial-bootscript, and is not meant to be re-configured through the EMA. Each SBC SWe has a redundant pair of physical ports for managing traffic.

Primary Management IPv4 AddressThis specifies the physical management IPv4 address associated with the primary management network.10.11.13.10
Primary Management Network MaskThis specifies the Netmask of the primary management network.255.255.255.0

Primary Management  Gateway IPv4 Address

This specifies the default gateway IPv4 address associated with the primary management network.

10.11.13.1

Primary Management IPv6 AddressThis specifies the physical management IPv6 address associated with the primary management network.fd00:10:6b50:4300::10b
Primary Management IPv6 Prefix Length (0-128)This specifies the prefix of the primary management network.60
Primary Management  Gateway IPv6 AddressThis specifies the default gateway IPv6 address associated with the primary management network.fd00:10:6b50:4300::1

...