Add_workflow_for_techpubs | ||||||||||
---|---|---|---|---|---|---|---|---|---|---|
|
This section describes upgrading the
Spacevars | ||
---|---|---|
|
Info | ||||
---|---|---|---|---|
| ||||
Prior to performing an application upgrade to the 7.0.0 release, upgrade the SBC Firmware firmware to the latest version on both Active active and Standby standby SBCs for in an HA pair.
|
Info | ||||
---|---|---|---|---|
| ||||
Ensure that the following requirements are met prior to performing an upgrade or LSWU to the 07.00.00R000 release:
|
Warning | ||
---|---|---|
| ||
This procedure is service impacting. |
Info | ||||
---|---|---|---|---|
| ||||
The BIOS firmware upgrade is not part of SBC application upgrade in
|
The following procedure describes the
Spacevars | ||
---|---|---|
|
LaunchEMALaunch EMA.
Navigate to Monitoring > Dashboard > System and Software Info to verify the software and HA peer status for both active and standby servers.
Caption | ||||
---|---|---|---|---|
| ||||
Caption | ||||
---|---|---|---|---|
| ||||
Navigate to Administration > System Administration > File Upload to upload the SBC application package to the active and standby SBC servers.
Click File Upload tab.
Caption | ||||
---|---|---|---|---|
| ||||
Click Add Files to Queue.
Browse for the SBC application package files in the File Upload screen and click Open.
Note |
---|
A new " For example: " |
Caption | ||||
---|---|---|---|---|
| ||||
The files are listed in the Upload Queue section. Click Upload All Files. The file upload starts.
Caption | ||||
---|---|---|---|---|
| ||||
Caption | ||||
---|---|---|---|---|
| ||||
|
Stop the application on Active on the active server using Administration > System Administration > Platform Management > Stop SBC Application.
Caption | ||||
---|---|---|---|---|
| ||||
The stop Stopping the application is a service-affecting operation. Click OK to continue the stop operation.
Caption | ||||
---|---|---|---|---|
| ||||
The application is stopped on the active server.
Launch the EMA Platform Mode on the Standby server.
Info | ||||
---|---|---|---|---|
| ||||
Once the Active active server (WFDSBC01a) is stopped, the Standby standby server (WFDSBC01b) automatically becomes active. |
Stop the application on the Standby server using Administration > System Administration > Platform Management > Stop SBC Application.
Caption | ||||
---|---|---|---|---|
| ||||
The stop application Stopping theapplication is a service-affecting operation. Click OK to continue the stop operation.
Caption | ||||
---|---|---|---|---|
| ||||
The application is stopped on the Standby server.
Caption | ||||
---|---|---|---|---|
| ||||
From the EMA of the initial active server (WFDSBC01a), Navigate to Administration > System Administration > Software Install/Upgrade tab.
Select the SBC Package Name to upgrade, and click Standalone Software Upgrade.
Info | ||||
---|---|---|---|---|
| ||||
Since, Because you are performing anona non-LSWU upgrade , and both the Active active and Standby standby SBCs are down, it is considered as Standalone Upgrade a standalone upgrade even for an HA pair. |
Caption | ||||
---|---|---|---|---|
| ||||
|
The signature file of the SBC package verifies the integrity of the package contents before proceeding with the SBC installation.
Caption | ||||
---|---|---|---|---|
| ||||
|
Click Start Upgrade.
Caption | ||||
---|---|---|---|---|
| ||||
|
The upgrade process starts on the Active active server (WFDSBC01a) and displays the upgrade status on in the Upgrade Log section.
Caption | ||||
---|---|---|---|---|
| ||||
Caption | ||||
---|---|---|---|---|
| ||||
Caption | ||||
---|---|---|---|---|
| ||||
Info | ||||
---|---|---|---|---|
| ||||
You may lose connectivity to the browser session as when the server goes for the rebootreboots. |
Info | ||||
---|---|---|---|---|
| ||||
This process takes approximately 45 minutes to complete on a single server. |
Warning |
---|
Once the upgrade is successful, clear the browser cache prior to accessing the SBC EMA. |
Log on to the EMA using the default credentials.
Caption | ||||
---|---|---|---|---|
| ||||
Caption | ||||
---|---|---|---|---|
| ||||
Verify the SBC installation status on the Administration > System Administration > Software Install/Upgrade screen.
Caption | ||||
---|---|---|---|---|
| ||||
Wait until the SBC upgrade is complete.
Caption | ||||
---|---|---|---|---|
| ||||
Verify the SBC application status on the Administration > System Administration > Platform Management screen.
Caption | ||||
---|---|---|---|---|
| ||||
Info | ||||
---|---|---|---|---|
| ||||
Once all the SBC process starts processes start running, continue upgrading the Standby SBC server. |
Follow the step 13 through step 18 to perform an upgrade on the Standby standby server (WFDSBC01b).
Verify the SBC application status on the Administration > System Administration > Platform Management screen.
Caption | ||||
---|---|---|---|---|
| ||||
Verify the Firmwarefirmware, ConnexIP OS and SBC application versions in Monitoring > Dashboard > System and Software Info.
Caption | ||||
---|---|---|---|---|
| ||||
Caption | ||||
---|---|---|---|---|
| ||||
Verify the system sync status is in Sync Completed state in All > System > Sync Status.
Caption | ||||
---|---|---|---|---|
| ||||
|
Pagebreak |
---|