This object is used to configure Gateway Trunk Group parameters.
| Include Page |
|---|
| IP_IGs_ServedBySeperateProcessors |
|---|
| IP_IGs_ServedBySeperateProcessors |
|---|
|
To View Gw Trunk Group
On SBC main screen, navigate to All > Address Context > Zone > Gw Trunk Group. The Gw Trunk Group can be checked for each Address Context and Zone or for all the Address Contexts and Zones created. Use the drop-down box to select the desired Address Context and Zone.
| Caption |
|---|
| 0 | Figure |
|---|
| 1 | All - Address Context - Zone - Gw Trunk Group Main Field |
|---|
|
 Image Modified
|
The Gw Trunk Group window is displayed
| Caption |
|---|
| 0 | Figure |
|---|
| 1 | All - Address Context - Zone - Gw Trunk Group |
|---|
|
Image Modified |
To Edit Gw Trunk Group
To edit any of the Gw Trunk Group in the list, click the radio button next to the specific Gw Trunk Group name.
| Caption |
|---|
| 0 | Figure |
|---|
| 1 | All - Address Context - Zone - Gw Trunk Group Highlighted |
|---|
|
Image Modified |
The Edit Selected Gw Trunk Group window is displayed below.
| Caption |
|---|
| 0 | Figure |
|---|
| 1 | All - Address Context - Zone - Gw Trunk Group Edit Window |
|---|
|
Image Modified |
Make the required changes and click Save at the right hand bottom of the panel to save the changes made.
To Create Gw Trunk Group
To create a new Gw Trunk Group, click New Gw Trunk Group tab on the Gw Trunk Group List panel.
| Caption |
|---|
| 0 | Figure |
|---|
| 1 | All - Address Context - Zone - Gw Trunk Group Fields |
|---|
|
Image Modified |
The Create New Gw Trunk Group window is displayed.
| Caption |
|---|
| 0 | Figure |
|---|
| 1 | All - Address Context - Zone - Gw Trunk Group Create Window |
|---|
|
Image Modified |
The following fields are displayed:
| Caption |
|---|
| 0 | Table |
|---|
| 1 | Gw Sig Trunk Group Parameters |
|---|
|
Parameter | Description |
|---|
Name
| Specifies the name of the Gateway Trunk Group. | State
| The administrative state of the gateway trunk group: | Mode
| The operational mode of the gateway trunk group: | Action
| The action when putting this gateway trunk group out Of Service. This object controls whether calls are forced off or allowed to dry up upon a mode out-of-service. Select any one of the option: dryup (default) force undefined
| Dryup Timeout
| Dry up timeout (in minutes) when this gateway trunk group is out Of Service with dry up action. Enter a value in the range of 0-1440. Default is 5 minutes. | Acc MC1Percent
| The percentage of calls to continue to send to a remote congested gateway (in MC1). Enter value in range of 0-100 percent. Default is 90 percent. | ACC MC2Percent
| The percentage of calls to continue to send to a remote congested gateway (in MC2). Enter value in range of 0-100 percent. Default is 70 percent. | ACC Timer
| Specifies the automatic congestion control timer. Enter value in range of 0-10. Default is 0. | Packet Outage | Minumum Duration
| This is the outage (in milliseconds) on a call for that call to be counted as part of the packet outage detection algorithm. Enter value in range of 0-65535 in milliseconds. Default is 6000 milliseconds. | Calls
| The number of calls with outages required within the current interval to declare a packet outage event. Enter value in range of 0-65535. Default is 1000. | Bandwidth Limit Reduction
| The amount to reduce the bandwidth limit (as a percentage of the configured limit) when a packet outage is detected. Enter value in range of 0-100 percent. Default is
50 percent. | Detection State
| Used to enable automatic bandwidth reduction when a packet outage is detected. Select any one of the option: disabled (default)
enabled
| Detection Interval
| The size of the packet outage detection interval in minutes. Enter value in range of 5- 1440 minutes. Default is 15 minutes. | | Call Reservation | Inbound
| The percent of channels reserved for inbound calls in IP gateway trunk groups. Must be 0-100, in increments of 5. Default is 0. | State
| The administrative state of the packet outage: disabled (default) enabled
| Priority Call
| The number of priority call resources (circuits or IP calls) to be reserved for this trunk group. Must be 0-100, default is 1. | Incoming Call
| The number of incoming call resources (circuits or IP calls) to be reserved for this trunk group. Must be 0-128, default is 1. | Outgoing Call
| The percentage of outgoing call resources (circuits or IP calls) to be reserved for this trunk group. This percentage is applied to the total number of circuits less the circuits reserved for incoming calls less the circuits reserved for priority calls. Must be 0-100, default is 10%. | | SILC | State
| The Administrative state of the SILC traffic control. Select any one of the option: disabled (default) enabled
| MC1Percent
| The percentage of calls to accept when the machine congestion level is 1. Enter value in range of 0-100 percent. Default is 75. | MC2Percent
| The percentage of calls to accept when the machine congestion level is 2. Enter value in range of 0-100 percent. Default is 25. | | Media | Media IP Interface Group Name
| Interface group to be used for media. | Source Address Filtering
| If enabled, filter out incoming media packets which do not match the expected source IP address and UDP port. | Direct Media Allowed
| Specifies whether to enable the direct-media path so that media flows directly between endpoints in the same direct-media group or not. The options are: disabled (default) enabled
|
|
To Copy Gw Trunk Group
To copy any of the created Gw Trunk Group and to make any minor changes, click the radio button next to the specific Gw Trunk Group to highlight the row.
| Caption |
|---|
| 0 | Figure |
|---|
| 1 | All - Address Context - Zone - Gw Trunk Group Highlighted |
|---|
|
Image Modified |
Click Copy Gw Trunk Group tab on the Gw Trunk Group List panel.
| Caption |
|---|
| 0 | Figure |
|---|
| 1 | All - Address Context - Zone - Gw Trunk Group Fields |
|---|
|
Image Modified |
The Copy Selected Gw Trunk Group window is displayed along with the field details which can be edited.
| Caption |
|---|
| 0 | Figure |
|---|
| 1 | All - Address Context - Zone - Gw Trunk Group Copy Window |
|---|
|
Image Modified |
Make the required changes to the required fields and click Save to save the changes. The copied Gw Trunk Group is displayed at the bottom of the original Gw Trunk Group in the Gw Trunk Group List panel.
To Delete Gw Trunk Group
To delete any of the created Gw Trunk Group, click the radio button next to the specific Gw Trunk Group which you want to delete.
| Caption |
|---|
| 0 | Figure |
|---|
| 1 | All - Address Context - Zone - Gw Trunk Group Highlighted |
|---|
|
Image Modified |
Click Delete at the end of the highlighted row. A delete confirmation message appears seeking your decision.
| Caption |
|---|
| 0 | Table |
|---|
| 1 | All - Address Context - Zone - Gw Trunk Group Delete Confirmation |
|---|
|
Image Modified |
Click Yes to remove the specific Gw Trunk Group from the list.