Page History

Add_workflow_for_techpubs

AUTH2	bscoggins
AUTH1	pmohan
REV5	dalves
REV6	radaikalam
REV3	dsevigny
REV4	aacharjya
REV1	wkwak
REV2	scgupta

Panel

In this section:

Table of Contents

maxLevel	2

Info

icon	false

To View IP Interface

On the

Spacevars

0	product

main screen, go to Configuration > System Provisioning > Category: Base Provisioning >IP Interface Group > IP Interface. The IP Interface window displays.
Caption
0 Figure
1 IP Interface
3 IP Interface

This window can display a listing of IP Interfaces for each Address Context, for each IP Interface Group or for all existing Address Contexts and IP Interface Groups. Use the drop-down menus at the top of the page to select the Address Contexts and/or IP Interface Groups of interest.
Caption
0 Figure
1 IP Interface Main Fields

To Edit IP Interface
To edit an IP Interface in the list, click the radio button next to the IP Interface name of interest.
Caption
0 Figure
1 IP Interface Highlight

The Edit Selected IP Interface window is displayed below.
Caption
0 Figure
1 IP Interface Edit Window

Make the required changes and click Save at the right hand bottom of the panel to save the changes made.
To Create IP Interface
To create a new IP Interface, click New IP Interface tab on the IP Interface List panel.
Caption
0 Figure
1 New IP Interface Button

The Create New IP Interface window is displayed.
Caption
0 Figure
1 IP Interface Create Window

The following fields are displayed:
Caption
0 Table
1 IP Interface Parameters

Parameter
Description
Name
The IP interface name.
Mode
The operational state of the IP Interface:
Out of Service—Set this state before changing admin-state to disabled.
In Service-— (default) This state is set by default when admin-state is enabled.
Note
When setting Mode to 'Out of Service', be sure to also set State to 'disabled'.
State The administrative state of the IP Interface:
disabled (default)—in this state the IP Interface is inactive, it does not respond to a ping.
enabled —in this state the IP Interface is active and it responds to a ping if the Ethernet cable is plugged in.
CE Name
The name of the computing element (1 - 255 characters) that hosts the port used by the IP interface.
Port Name
The physical port name (example: pkt0, ..., pkt3) used by this IP interface.
IP Address
The IP address of the Interface.

• IPv4—This is V4 IP address in dotted decimal form (for example 128.127.50.224).
• IPv6—This is V6 IP address in hexadecimal/colon form (for example, 1280:1276:3350:2224:2222:3333:8888:1245 or fd00:21:445:128::7880).
Prefix
The IP subnet prefix of this Interface.
Alt IP Address
Specifies alternative (secondary) IP address for the configured packet IP interface. The alternative IP address is optional.

The following IP address types are supported:
IPv4—This is V4 IP address in dotted decimal form (for example 128.127.50.224).
IPv6—This is V6 IP address in hexadecimal/colon form (for example, 1280:1276:3350:2224:2222:3333:8888:1245 or fd00:21:445:128::7880).
Note
Modify an alternative IP address only after changing the Packet IP interface to disabled state.
Alt Media Ip Address
Use this parameter to specify up to 14 additional IPv4 and/or IPv6 media IP addresses on this IP interface. Any combination of IPv4 and IPv6 is allowed. The following rules apply when configuring alternate media IP addresses:
An IPv4/IPv6 alternate media IP address is only allowed if an IPv4/IPv6 address is defined in the primary or alternate (main) address.
An alternate media IP address must be in the same network as the primary media address (of the same IP version). Hence, CPX needs to determine the subnet based on the primary/alt IP address and primary/alt prefix, and then verify that the given alternate media address is on the same subnet.
An alternate media IP address may be added while the IP interface is enabled and in-service. However, the IP can only be deleted when the IP interface state is set to "disabled".
Alt Prefix
The alternative IP subnet prefix of this Interface. It should be between 0-128.
Action
The method by which calls are torn down when operational state goes to out of service:
dryup (default)—calls remain active until the tear downtime interval expires.
force—calls are dropped immediately.
Dryup Timeout
The time (in minutes) to wait for all calls to complete before placing the GATEWAY service in out Of Service oper-state. Must be 0-1440 (minutes), default is 0. A value of 0 means wait indefinitely.
Bw Contingency
The percentage of maximum bandwidth that is reserved for contingency (that is, non-media). Value must be 0-100 percent.

The maximum bandwidth is the bandwidth normally available for media on the interface. (This is based on the configured bandwidth limit or the physical port bandwidth limit minus approximately 5% for signaling traffic.) The contingency factor effectively reserves a portion of this bandwidth for non-media.
Vlan Tag
Assign a VLAN ID to each IP Interface which will include one or more SUBINTERFACEs. When the parent IP Interface is created, this parameter is assigned the NULL (0) tag. When the IP Interface is enabled for VLAN TAG STATE, in order to provision a SUBINTERFACE, this parameter must already be set to a value in the 2-4094 range or the enable command will fail.

The parent IP Interface will receive non-tagged or NULL (0) tagged frames. A VLAN ID in the range cited above must also be assigned to each IP Interface when it is configured. This value must be unique on a physical port.
Include Page
VLAN_limitation_on_5100
VLAN_limitation_on_5100
Bandwidth
Specifies the maximum amount of bandwidth allowed in units of bytes per second. Must be 0-118750000 as follows:

• 0—Allow bandwidth subscriptions up to the maximum supported on the physical port.
• non-zero—Allow up to the specified number of bytes per second on this IP interface. The aggregate of this number and all previously provisioned IP interfaces must not exceed the physical port bandwidth.
Enter all the required fields.
Tip
title Tip
Click Show only required fields at the bottom left-hand portion of the panel to view and enter only the required fields to create a IP Interface.

To Delete IP Interface
To delete any of the created IP Interface, click the radio button next to the specific IP Interface which you want to delete.
Caption
0 Figure
1 IP Interface Highlight

Click Delete at the end of the highlighted row. A delete confirmation message appears seeking your decision.
Caption
0 Figure
1 IP Interface Delete Confirmation

Click Yes to remove the specific Ip Interface from the list.
Pagebreak

Space shortcuts

Page tree

Versions Compared

Old Version 8

New Version Current

Key

To View IP Interface

To Edit IP Interface

To Create IP Interface

To Delete IP Interface