Page History

Specifies the state of this filter. The options are:

• Enabled: If enabled, this filter can be used for Call Trace.

• Disabled (default): If disabled, it is not used for Call Trace.


Specifies the type of logs that need to be captured while running the Call Trace. The options are:

• TRC logs: Capture trace information (.trc logs) only.
• TRC and PKT logs: Capture trace information (.trc logs) and media information (.pkt logs).

Specifies the level of details that need to be capture in the log file when the trace is complete. The options are:

• Level 1 - Everything
• Level 2 - Everything but raw hex dump.
• Level 3 - Only external message information and errors.
• Level 4 - Only SIP PDU events.

Specifies the criteria that need to be captured in the logs in a Call Trace (these are optional). The options are:

• Called Number: Specifies the called party number to trace. An X or x means accept anything in that digit position. For example, 617xxx1212 would filter for all numbers 6170001212 through 6179991212. The % symbol acts as a wildcard for all remaining digits. For example, use 978% to trace all calls with a 978 prefix. Field Length is upto 30 characters.
• Calling Number: Specifies the calling party number to trace. An X or x means accept anything in that digit position. For example, 617xxx1212 would filter for all numbers 6170001212 through 6179991212. The % symbol acts as a wildcard for all remaining digits. For example, use 978% to trace all calls with a 978 prefix. Field Length is upto 30 characters.
  NOTE: The following characters are accepted by the SBC when specifying the Call Filter search criteria :

  • Digits 0-9

  • Plus (+) symbol

  • Wilcard characters (“x” or “X”) to match any single digit within the search string

  • Wilcard symbol (%) to match any digits from that point forward

• Contractor Number: Specifies the contractor number to trace. An X or x means accept anything in that digit position. For example, 617xxx1212 would filter for all numbers 6170001212 through 6179991212. The % symbol acts as a wildcard for all remaining digits. For example, use 978% to trace all calls with a 978 prefix. Field Length is upto 30 characters.


  Note
  For the above parameters, use "X" or "x" wildcard characters to match any single digit and "%" symbol to match any digits from that point forward.

• Redirecting Number:  Specifies the redirecting number to trace. An X or x means accept anything in that digit position. For example, 617xxx1212 would filter for all numbers 6170001212 through 6179991212. The % symbol acts as a wildcard for all remaining digits. For example, use 978% to trace all calls with a 978 prefix. Field Length is upto 30 characters.
• CDDN number: Specifies the Called Directory Number to trace. Field Length is upto 30 characters.

Transfer capability: Specifies the transfer capability of the call trace filter. Options are:

• • Audio31Khz - 3.1 kHz Audio - ITC 3.1 kHz audio calls are traced. The default setting is disabled.
  • Speech - ITC Speech based calls are traced. The default setting is disabled.
  • Unrestricted - Calls with ITC Unrestricted are traced. The default setting is disabled.
  • Unrestricted With Tones - Unrestricted Digital Information With Tones Announcements - Calls with ITC Unrestricted Digital Information With Tones Announcements are traced. The default setting is disabled.
  • video - Calls with ITC Video are traced. The default setting is disabled.

• Trunk Group: The name of a trunk group to trace. This string must match the trunk group name exactly. You cannot use wildcard characters for this argument. Field Length is upto 23 characters.
• Peer IP Address: Specifies the peer IpV4 or IpV6 Address for call tracing.
  

Specifies the criteria to stop the Call Trace. The options are:

• When a match occurs in this filter, stop trying to match the other filters
• Continue to try to match up to two other filters after a match is found in this filter (default)


Specifies the duration for the Call Trace to run on the selected filter. The options are:

• Run trace until stopped (by clicking the Stop Trace button): If selected, the trace will keep running till it is stopped manually (by clicking the Stop Trace button).

• Stop trace after __ minutes: If selected, add the number of minutes for the Call Trace to run. The value ranges from 1 to 360 minutes and the default value is 360 minutes.


Use this object to specify the system-wide call trace error filter trigger criteria.

• none (default)—No SIP PDU logging for this error filter.
• Any—Log all SIP PDUs that meet the requirement of the Parse Error, Out of Dialog, and Early Attempt options below.
• Parse Error—Log received SIP PDUs that fail parsing. If an error is detected by SIP signaling, the accompanying PDUs will not be associated with any dialog, including an existing dialog. Hence all in dialog and out of dialog PDUs are assigned to this category. If an error is detected at the front end pre-parser, the PDU is logged by this software and not forwarded to SIP signaling. This prevents an offending PDU from being logged by both the pre-parser and SIP signaling.
• Out of Dialog—Log incoming syntactically correct SIP PDUs (except INVITE) that do not belong to an existing dialog.
• Early Attempt—Logs incoming SIP PDUs that result in early termination of the call (by either the pre-parser or SIP signaling).

For further details on error logs, see the section Call Trace Log Messages.

Displays the current status of the Call Trace.

• When there are no trace running, the application states Call trace stopped with a red dot.
• when a trace is running, the application states Call trace running with a green dot.