This article describes the steps necessary to configure the
(SBC) for SIP Trunking using
Multiple IP Interface support – available in since
UX Release 1.0.2:
...
LAN Port 2/Ethernet 2 IP
Deck of Cards |
---|
|
Card |
---|
| Configure the public IP address 10.51.100.89 in the SBC. In the WebUI, access Tasks and select Modify Ethernet IP Address. Caption |
---|
0 | Figure |
---|
1 | Modify Ethernet IP |
---|
|
| Note that LAN Port 1 134.56.225.202 is already configured on the node which you'd be using to URL into WebUI. Following screenshot depicts the verification of LAN 1 configuration: |
Card |
---|
| Configure the public IP address of 10.51.100.89 in theSBCthe SBC. In the WebUI, access Tasks and select Modify Ethernet IP Address. Caption |
---|
0 | Figure |
---|
1 | Modify Ethernet IP |
---|
|
|
|
|
Transformation Table
There are 4 different transformations used in this exercise:
...
Panel |
---|
|
Caption |
---|
0 | Figure |
---|
1 | 1xxx Transformation |
---|
| Image Modified |
|
Translation table for LAN-1 (2xxx) extensions
Panel |
---|
|
Caption |
---|
0 | Figure |
---|
1 | 2xxx Transformation |
---|
| Image Modified |
|
...
Translation table for LAN-2 (5xxx) extensions
Panel |
---|
|
Caption |
---|
0 | Figure |
---|
1 | 5xxx Transformation |
---|
| Image Modified |
|
Translation table for PSTN (3xxx) extensions
Panel |
---|
|
Caption |
---|
0 | Figure |
---|
1 | 3xxx Transformation |
---|
| Image Modified |
|
Call Routing Tables
There are 3 different Call Routing Table entries used in this exercise:
...
Panel |
---|
|
Caption |
---|
0 | Figure |
---|
1 | Routing Calls From OCS Endpoints |
---|
| Image Modified |
|
Routing Calls from Multiple IP Endpoints (LAN-1 and LAN-2 endpoints)
Panel |
---|
|
Caption |
---|
0 | Figure |
---|
1 | Routing Calls From Multiple IP Endpoints |
---|
| Image Modified |
|
Routing Calls from PSTN Endpoints
Panel |
---|
|
Caption |
---|
0 | Figure |
---|
1 | Routing Calls From PSTN Endpoints |
---|
| Image Modified |
|
Signaling Groups
Signaling Groups for OCS
Panel |
---|
|
Caption |
---|
0 | Figure |
---|
1 | Signaling Groups for OCS |
---|
| Image Modified |
|
Signaling Groups for LAN-1 endpoints
Panel |
---|
|
Caption |
---|
0 | Figure |
---|
1 | Signaling Groups for LAN-1 Endpoints |
---|
|
|
|
Signaling Groups for LAN-2 endpoints
...
Panel |
---|
|
Caption |
---|
0 | Figure |
---|
1 | Signaling Groups for LAN-2 Endpoints |
---|
|
|
|
Signaling Group for PSTN endpoints
Panel |
---|
|
Caption |
---|
0 | Figure |
---|
1 | Signaling Group for PSTN Endpoints |
---|
|
|
|
Additional Configuration step for
SBC SWe Lite
Adding Static IP Routes
...
The previous steps complete the necessary configuration requirements for implementing the Multiple IP feature on the
. However, if deploying on the , in addition to previous steps, perform the following step to complete the Multiple IP feature support on the . Panel |
---|
Note |
---|
|
All end-points located in a private or public network must be reachable through a next-hop gateway, as driven by the network environment. |
Panel |
---|
Caption |
---|
0 | Figure |
---|
1 | Modifying Ethernet IP |
---|
3 | Modifying Ethernet IP |
---|
| Image Modified |
|