...
| Deck of Cards |
|---|
|
| Card |
|---|
| Configure the public IP address 10.51.100.89 in the Sonus SBC 1000/2000. In the WebUI, access Tasks and select Modify Ethernet IP Address. | Panel |
|---|
| | Caption |
|---|
| 0 | Figure |
|---|
| 1 | Modify Ethernet IP |
|---|
|  Image Modified
|
|
Note that LAN Port 1 134.56.225.202 is already configured on the node which you'd be using to URL into WebUI. Following screenshot depicts the verification of LAN 1 configuration: |
| Card |
|---|
| Configure the public IP address of 10.51.100.89 in theSonus SBC 1000/2000. In the WebUI, access Tasks and select Modify Ethernet IP Address. | Panel |
|---|
| | Caption |
|---|
| 0 | Figure |
|---|
| 1 | Modify Ethernet IP |
|---|
| Image Modified |
|
|
|
Transformation Table
There are 4 different transformations used in this exercise:
Translation table for OCS (1xxx) extensions
| Panel |
|---|
|
| Caption |
|---|
| 0 | Figure |
|---|
| 1 | 1xxx Transformation |
|---|
|  Image Modified
|
|
Translation table for LAN-1 (2xxx) extensions
| Panel |
|---|
|
| Caption |
|---|
| 0 | Figure |
|---|
| 1 | 2xxx Transformation |
|---|
|  Image Modified
|
|
Translation table for LAN-2 (5xxx) extensions
| Panel |
|---|
|
| Caption |
|---|
| 0 | Figure |
|---|
| 1 | 5xxx Transformation |
|---|
|  Image Modified
|
|
Translation table for PSTN (3xxx) extensions
| Panel |
|---|
|
| Caption |
|---|
| 0 | Figure |
|---|
| 1 | 3xxx Transformation |
|---|
|  Image Modified
|
|
Call Routing Tables
There are 3 different Call Routing Table entries used in this exercise:
Routing Calls from OCS Endpoints
| Panel |
|---|
|
| Caption |
|---|
| 0 | Figure |
|---|
| 1 | Routing Calls From OCS Endpoints |
|---|
|  Image Modified
|
|
Routing Calls from Multiple IP Endpoints (LAN-1 and LAN-2 endpoints)
| Panel |
|---|
|
| Caption |
|---|
| 0 | Figure |
|---|
| 1 | Routing Calls From Multiple IP Endpoints |
|---|
|  Image Modified
|
|
Routing Calls from PSTN Endpoints
| Panel |
|---|
|
| Caption |
|---|
| 0 | Figure |
|---|
| 1 | Routing Calls From PSTN Endpoints |
|---|
|  Image Modified
|
|
Signaling Groups
Signaling Groups for OCS
| Panel |
|---|
|
| Caption |
|---|
| 0 | Figure |
|---|
| 1 | Signaling Groups For OCS |
|---|
|  Image Modified
|
|
Signaling Groups for LAN-1 endpoints
| Panel |
|---|
|
| Caption |
|---|
| 0 | Figure |
|---|
| 1 | Signaling Groups For LAN-1 Endpoints |
|---|
|  Image Modified
|
|
Signaling Groups for LAN-2 endpoints
...
If there is no NAT device between Sonus SBC 1000/2000 and the SIP-trunking peer, then NAT Traversal must be set to NONE as shown below:
| Panel |
|---|
|
| Caption |
|---|
| 0 | Figure |
|---|
| 1 | Signaling Groups For LAN-2 Endpoints |
|---|
|  Image Modified
|
|
Signaling Group for PSTN endpoints
| Panel |
|---|
|
| Caption |
|---|
| 0 | Figure |
|---|
| 1 | Signaling Group For PSTN Endpoints |
|---|
|  Image Modified
|
|